diff --git a/target/linux/mediatek/patches-5.4/0603-net-dsa-mt7530-Extend-device-data-ready-for-adding-a.patch b/target/linux/mediatek/patches-5.4/0603-net-dsa-mt7530-Extend-device-data-ready-for-adding-a.patch
new file mode 100644
index 0000000..84579ac
--- /dev/null
+++ b/target/linux/mediatek/patches-5.4/0603-net-dsa-mt7530-Extend-device-data-ready-for-adding-a.patch
@@ -0,0 +1,458 @@
+From: Landen Chao <landen.chao@mediatek.com>
+Date: Fri, 4 Sep 2020 22:21:57 +0800
+Subject: [PATCH] net: dsa: mt7530: Extend device data ready for adding a
+ new hardware
+
+Add a structure holding required operations for each device such as device
+initialization, PHY port read or write, a checker whether PHY interface is
+supported on a certain port, MAC port setup for either bus pad or a
+specific PHY interface.
+
+The patch is done for ready adding a new hardware MT7531, and keep the
+same setup logic of existing hardware.
+
+Signed-off-by: Landen Chao <landen.chao@mediatek.com>
+Signed-off-by: Sean Wang <sean.wang@mediatek.com>
+---
+
+--- a/drivers/net/dsa/mt7530.c
++++ b/drivers/net/dsa/mt7530.c
+@@ -373,8 +373,9 @@ mt7530_fdb_write(struct mt7530_priv *pri
+ 		mt7530_write(priv, MT7530_ATA1 + (i * 4), reg[i]);
+ }
+ 
++/* Setup TX circuit including relevant PAD and driving */
+ static int
+-mt7530_pad_clk_setup(struct dsa_switch *ds, int mode)
++mt7530_pad_clk_setup(struct dsa_switch *ds, phy_interface_t interface)
+ {
+ 	struct mt7530_priv *priv = ds->priv;
+ 	u32 ncpo1, ssc_delta, trgint, i, xtal;
+@@ -388,7 +389,7 @@ mt7530_pad_clk_setup(struct dsa_switch *
+ 		return -EINVAL;
+ 	}
+ 
+-	switch (mode) {
++	switch (interface) {
+ 	case PHY_INTERFACE_MODE_RGMII:
+ 		trgint = 0;
+ 		/* PLL frequency: 125MHz */
+@@ -410,7 +411,8 @@ mt7530_pad_clk_setup(struct dsa_switch *
+ 		}
+ 		break;
+ 	default:
+-		dev_err(priv->dev, "xMII mode %d not supported\n", mode);
++		dev_err(priv->dev, "xMII interface %d not supported\n",
++			interface);
+ 		return -EINVAL;
+ 	}
+ 
+@@ -1333,12 +1335,11 @@ mt7530_setup(struct dsa_switch *ds)
+ 	return 0;
+ }
+ 
+-static void mt7530_phylink_mac_config(struct dsa_switch *ds, int port,
+-				      unsigned int mode,
+-				      const struct phylink_link_state *state)
++static bool
++mt7530_phy_mode_supported(struct dsa_switch *ds, int port,
++			  const struct phylink_link_state *state)
+ {
+ 	struct mt7530_priv *priv = ds->priv;
+-	u32 mcr_cur, mcr_new;
+ 
+ 	switch (port) {
+ 	case 0: /* Internal phy */
+@@ -1347,33 +1348,114 @@ static void mt7530_phylink_mac_config(st
+ 	case 3:
+ 	case 4:
+ 		if (state->interface != PHY_INTERFACE_MODE_GMII)
+-			return;
++			goto unsupported;
+ 		break;
+ 	case 5: /* 2nd cpu port with phy of port 0 or 4 / external phy */
+-		if (priv->p5_interface == state->interface)
+-			break;
+ 		if (!phy_interface_mode_is_rgmii(state->interface) &&
+ 		    state->interface != PHY_INTERFACE_MODE_MII &&
+ 		    state->interface != PHY_INTERFACE_MODE_GMII)
+-			return;
++			goto unsupported;
++		break;
++	case 6: /* 1st cpu port */
++		if (state->interface != PHY_INTERFACE_MODE_RGMII &&
++		    state->interface != PHY_INTERFACE_MODE_TRGMII)
++			goto unsupported;
++		break;
++	default:
++		dev_err(priv->dev, "%s: unsupported port: %i\n", __func__,
++			port);
++		goto unsupported;
++	}
++
++	return true;
++
++unsupported:
++	return false;
++}
++
++static bool
++mt753x_phy_mode_supported(struct dsa_switch *ds, int port,
++			  const struct phylink_link_state *state)
++{
++	struct mt7530_priv *priv = ds->priv;
++
++	return priv->info->phy_mode_supported(ds, port, state);
++}
++
++static int
++mt753x_pad_setup(struct dsa_switch *ds, const struct phylink_link_state *state)
++{
++	struct mt7530_priv *priv = ds->priv;
++
++	return priv->info->pad_setup(ds, state->interface);
++}
++
++static int
++mt7530_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
++		  phy_interface_t interface)
++{
++	struct mt7530_priv *priv = ds->priv;
++
++	/* Only need to setup port5. */
++	if (port != 5)
++		return 0;
++
++	mt7530_setup_port5(priv->ds, interface);
++
++	return 0;
++}
++
++static int
++mt753x_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
++		  const struct phylink_link_state *state)
++{
++	struct mt7530_priv *priv = ds->priv;
++
++	return priv->info->mac_port_config(ds, port, mode, state->interface);
++}
++
++static void
++mt753x_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
++			  const struct phylink_link_state *state)
++{
++	struct mt7530_priv *priv = ds->priv;
++	u32 mcr_cur, mcr_new;
++
++	if (!mt753x_phy_mode_supported(ds, port, state))
++		goto unsupported;
++
++	switch (port) {
++	case 0: /* Internal phy */
++	case 1:
++	case 2:
++	case 3:
++	case 4:
++		if (state->interface != PHY_INTERFACE_MODE_GMII)
++			goto unsupported;
++		break;
++	case 5: /* 2nd cpu port with phy of port 0 or 4 / external phy */
++		if (priv->p5_interface == state->interface)
++			break;
++
++		if (mt753x_mac_config(ds, port, mode, state) < 0)
++			goto unsupported;
+ 
+-		mt7530_setup_port5(ds, state->interface);
+ 		break;
+ 	case 6: /* 1st cpu port */
+ 		if (priv->p6_interface == state->interface)
+ 			break;
+ 
+-		if (state->interface != PHY_INTERFACE_MODE_RGMII &&
+-		    state->interface != PHY_INTERFACE_MODE_TRGMII)
+-			return;
++		mt753x_pad_setup(ds, state);
+ 
+-		/* Setup TX circuit incluing relevant PAD and driving */
+-		mt7530_pad_clk_setup(ds, state->interface);
++		if (mt753x_mac_config(ds, port, mode, state) < 0)
++			goto unsupported;
+ 
+ 		priv->p6_interface = state->interface;
+ 		break;
+ 	default:
+-		dev_err(ds->dev, "%s: unsupported port: %i\n", __func__, port);
++unsupported:
++		dev_err(ds->dev, "%s: unsupported %s port: %i\n",
++			__func__, phy_modes(state->interface), port);
+ 		return;
+ 	}
+ 
+@@ -1441,61 +1523,44 @@ static void mt7530_phylink_mac_link_up(s
+ 	mt7530_set(priv, MT7530_PMCR_P(port), mcr);
+ }
+ 
+-static void mt7530_phylink_validate(struct dsa_switch *ds, int port,
+-				    unsigned long *supported,
+-				    struct phylink_link_state *state)
++static void
++mt7530_mac_port_validate(struct dsa_switch *ds, int port,
++			 unsigned long *supported)
+ {
++	if (port == 5)
++		phylink_set(supported, 1000baseX_Full);
++}
++
++static void
++mt753x_phylink_validate(struct dsa_switch *ds, int port,
++			unsigned long *supported,
++			struct phylink_link_state *state)
++{
++	struct mt7530_priv *priv = ds->priv;
+ 	__ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
+ 
+-	switch (port) {
+-	case 0: /* Internal phy */
+-	case 1:
+-	case 2:
+-	case 3:
+-	case 4:
+-		if (state->interface != PHY_INTERFACE_MODE_NA &&
+-		    state->interface != PHY_INTERFACE_MODE_GMII)
+-			goto unsupported;
+-		break;
+-	case 5: /* 2nd cpu port with phy of port 0 or 4 / external phy */
+-		if (state->interface != PHY_INTERFACE_MODE_NA &&
+-		    !phy_interface_mode_is_rgmii(state->interface) &&
+-		    state->interface != PHY_INTERFACE_MODE_MII &&
+-		    state->interface != PHY_INTERFACE_MODE_GMII)
+-			goto unsupported;
+-		break;
+-	case 6: /* 1st cpu port */
+-		if (state->interface != PHY_INTERFACE_MODE_NA &&
+-		    state->interface != PHY_INTERFACE_MODE_RGMII &&
+-		    state->interface != PHY_INTERFACE_MODE_TRGMII)
+-			goto unsupported;
+-		break;
+-	default:
+-		dev_err(ds->dev, "%s: unsupported port: %i\n", __func__, port);
+-unsupported:
++	if (state->interface != PHY_INTERFACE_MODE_NA &&
++	    !mt753x_phy_mode_supported(ds, port, state)) {
+ 		linkmode_zero(supported);
+ 		return;
+ 	}
+ 
+ 	phylink_set_port_modes(mask);
+-	phylink_set(mask, Autoneg);
+ 
+-	if (state->interface == PHY_INTERFACE_MODE_TRGMII) {
+-		phylink_set(mask, 1000baseT_Full);
+-	} else {
++	if (state->interface != PHY_INTERFACE_MODE_TRGMII) {
+ 		phylink_set(mask, 10baseT_Half);
+ 		phylink_set(mask, 10baseT_Full);
+ 		phylink_set(mask, 100baseT_Half);
+ 		phylink_set(mask, 100baseT_Full);
+-
+-		if (state->interface != PHY_INTERFACE_MODE_MII) {
+-			/* This switch only supports 1G full-duplex. */
+-			phylink_set(mask, 1000baseT_Full);
+-			if (port == 5)
+-				phylink_set(mask, 1000baseX_Full);
+-		}
++		phylink_set(mask, Autoneg);
+ 	}
+ 
++	/* This switch only supports 1G full-duplex. */
++	if (state->interface != PHY_INTERFACE_MODE_MII)
++		phylink_set(mask, 1000baseT_Full);
++
++	priv->info->mac_port_validate(ds, port, mask);
++
+ 	phylink_set(mask, Pause);
+ 	phylink_set(mask, Asym_Pause);
+ 
+@@ -1591,12 +1656,45 @@ static int mt7530_set_mac_eee(struct dsa
+ 	return 0;
+ }
+ 
++static int
++mt753x_phylink_mac_link_state(struct dsa_switch *ds, int port,
++			      struct phylink_link_state *state)
++{
++	struct mt7530_priv *priv = ds->priv;
++
++	return priv->info->mac_port_get_state(ds, port, state);
++}
++
++static int
++mt753x_setup(struct dsa_switch *ds)
++{
++	struct mt7530_priv *priv = ds->priv;
++
++	return priv->info->sw_setup(ds);
++}
++
++static int
++mt753x_phy_read(struct dsa_switch *ds, int port, int regnum)
++{
++	struct mt7530_priv *priv = ds->priv;
++
++	return priv->info->phy_read(ds, port, regnum);
++}
++
++static int
++mt753x_phy_write(struct dsa_switch *ds, int port, int regnum, u16 val)
++{
++	struct mt7530_priv *priv = ds->priv;
++
++	return priv->info->phy_write(ds, port, regnum, val);
++}
++
+ static const struct dsa_switch_ops mt7530_switch_ops = {
+ 	.get_tag_protocol	= mtk_get_tag_protocol,
+-	.setup			= mt7530_setup,
++	.setup			= mt753x_setup,
+ 	.get_strings		= mt7530_get_strings,
+-	.phy_read		= mt7530_phy_read,
+-	.phy_write		= mt7530_phy_write,
++	.phy_read		= mt753x_phy_read,
++	.phy_write		= mt753x_phy_write,
+ 	.get_ethtool_stats	= mt7530_get_ethtool_stats,
+ 	.get_sset_count		= mt7530_get_sset_count,
+ 	.port_enable		= mt7530_port_enable,
+@@ -1613,18 +1711,43 @@ static const struct dsa_switch_ops mt753
+ 	.port_vlan_del		= mt7530_port_vlan_del,
+ 	.port_mirror_add	= mt7530_port_mirror_add,
+ 	.port_mirror_del	= mt7530_port_mirror_del,
+-	.phylink_validate	= mt7530_phylink_validate,
+-	.phylink_mac_link_state = mt7530_phylink_mac_link_state,
+-	.phylink_mac_config	= mt7530_phylink_mac_config,
++	.phylink_validate	= mt753x_phylink_validate,
++	.phylink_mac_link_state	= mt753x_phylink_mac_link_state,
++	.phylink_mac_config	= mt753x_phylink_mac_config,
+ 	.phylink_mac_link_down	= mt7530_phylink_mac_link_down,
+ 	.phylink_mac_link_up	= mt7530_phylink_mac_link_up,
+ 	.get_mac_eee		= mt7530_get_mac_eee,
+ 	.set_mac_eee		= mt7530_set_mac_eee,
+ };
+ 
++static const struct mt753x_info mt753x_table[] = {
++	[ID_MT7621] = {
++		.id = ID_MT7621,
++		.sw_setup = mt7530_setup,
++		.phy_read = mt7530_phy_read,
++		.phy_write = mt7530_phy_write,
++		.pad_setup = mt7530_pad_clk_setup,
++		.phy_mode_supported = mt7530_phy_mode_supported,
++		.mac_port_validate = mt7530_mac_port_validate,
++		.mac_port_get_state = mt7530_phylink_mac_link_state,
++		.mac_port_config = mt7530_mac_config,
++	},
++	[ID_MT7530] = {
++		.id = ID_MT7530,
++		.sw_setup = mt7530_setup,
++		.phy_read = mt7530_phy_read,
++		.phy_write = mt7530_phy_write,
++		.pad_setup = mt7530_pad_clk_setup,
++		.phy_mode_supported = mt7530_phy_mode_supported,
++		.mac_port_validate = mt7530_mac_port_validate,
++		.mac_port_get_state = mt7530_phylink_mac_link_state,
++		.mac_port_config = mt7530_mac_config,
++	},
++};
++
+ static const struct of_device_id mt7530_of_match[] = {
+-	{ .compatible = "mediatek,mt7621", .data = (void *)ID_MT7621, },
+-	{ .compatible = "mediatek,mt7530", .data = (void *)ID_MT7530, },
++	{ .compatible = "mediatek,mt7621", .data = &mt753x_table[ID_MT7621], },
++	{ .compatible = "mediatek,mt7530", .data = &mt753x_table[ID_MT7530], },
+ 	{ /* sentinel */ },
+ };
+ MODULE_DEVICE_TABLE(of, mt7530_of_match);
+@@ -1662,8 +1785,21 @@ mt7530_probe(struct mdio_device *mdiodev
+ 	/* Get the hardware identifier from the devicetree node.
+ 	 * We will need it for some of the clock and regulator setup.
+ 	 */
+-	priv->id = (unsigned int)(unsigned long)
+-		of_device_get_match_data(&mdiodev->dev);
++	priv->info = of_device_get_match_data(&mdiodev->dev);
++	if (!priv->info)
++		return -EINVAL;
++
++	/* Sanity check if these required device operations are filled
++	 * properly.
++	 */
++	if (!priv->info->sw_setup || !priv->info->pad_setup ||
++	    !priv->info->phy_read || !priv->info->phy_write ||
++	    !priv->info->phy_mode_supported ||
++	    !priv->info->mac_port_validate ||
++	    !priv->info->mac_port_get_state || !priv->info->mac_port_config)
++		return -EINVAL;
++
++	priv->id = priv->info->id;
+ 
+ 	if (priv->id == ID_MT7530) {
+ 		priv->core_pwr = devm_regulator_get(&mdiodev->dev, "core");
+--- a/drivers/net/dsa/mt7530.h
++++ b/drivers/net/dsa/mt7530.h
+@@ -11,7 +11,7 @@
+ #define MT7530_NUM_FDB_RECORDS		2048
+ #define MT7530_ALL_MEMBERS		0xff
+ 
+-enum {
++enum mt753x_id {
+ 	ID_MT7530 = 0,
+ 	ID_MT7621 = 1,
+ };
+@@ -451,6 +451,40 @@ static const char *p5_intf_modes(unsigne
+ 	}
+ }
+ 
++/* struct mt753x_info -	This is the main data structure for holding the specific
++ *			part for each supported device
++ * @sw_setup:		Holding the handler to a device initialization
++ * @phy_read:		Holding the way reading PHY port
++ * @phy_write:		Holding the way writing PHY port
++ * @pad_setup:		Holding the way setting up the bus pad for a certain
++ *			MAC port
++ * @phy_mode_supported:	Check if the PHY type is being supported on a certain
++ *			port
++ * @mac_port_validate:	Holding the way to set addition validate type for a
++ *			certan MAC port
++ * @mac_port_get_state: Holding the way getting the MAC/PCS state for a certain
++ *			MAC port
++ * @mac_port_config:	Holding the way setting up the PHY attribute to a
++ *			certain MAC port
++ */
++struct mt753x_info {
++	enum mt753x_id id;
++
++	int (*sw_setup)(struct dsa_switch *ds);
++	int (*phy_read)(struct dsa_switch *ds, int port, int regnum);
++	int (*phy_write)(struct dsa_switch *ds, int port, int regnum, u16 val);
++	int (*pad_setup)(struct dsa_switch *ds, phy_interface_t interface);
++	bool (*phy_mode_supported)(struct dsa_switch *ds, int port,
++				   const struct phylink_link_state *state);
++	void (*mac_port_validate)(struct dsa_switch *ds, int port,
++				  unsigned long *supported);
++	int (*mac_port_get_state)(struct dsa_switch *ds, int port,
++				  struct phylink_link_state *state);
++	int (*mac_port_config)(struct dsa_switch *ds, int port,
++			       unsigned int mode,
++			       phy_interface_t interface);
++};
++
+ /* struct mt7530_priv -	This is the main data structure for holding the state
+  *			of the driver
+  * @dev:		The device pointer
+@@ -476,6 +510,7 @@ struct mt7530_priv {
+ 	struct regulator	*core_pwr;
+ 	struct regulator	*io_pwr;
+ 	struct gpio_desc	*reset;
++	const struct mt753x_info *info;
+ 	unsigned int		id;
+ 	bool			mcm;
+ 	phy_interface_t		p6_interface;