target/linux/ath79/dts/qca9558_openmesh_om5p-ac-v2.dts

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT

#include "qca955x.dtsi"

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>

/ {
	compatible = "openmesh,om5p-ac-v2", "qca,qca9558";
	model = "OpenMesh OM5P-AC v2";

	chosen {
		/delete-property/ bootargs;
	};

	aliases {
		serial0 = &uart;
		led-boot = &led_power_blue;
		led-failsafe = &led_power_blue;
		led-running = &led_power_blue;
		led-upgrade = &led_power_blue;
		label-mac-device = &eth0;
	};

	leds {
		compatible = "gpio-leds";

		wifi_green {
			label = "green:wifi";
			gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
			linux,default-trigger = "phy0tpt";
		};

		led_power_blue: power_blue {
			label = "blue:power";
			gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
			default-state = "on";
		};

		wifi_yellow {
			label = "yellow:wifi";
			gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
		};

		wifi_red {
			label = "red:wifi";
			gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
		};
	};

	keys {
		compatible = "gpio-keys";

		reset {
			label = "reset";
			linux,code = <KEY_RESTART>;
			gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
		};
	};

	i2c {
		compatible = "i2c-gpio";
		gpios = <&gpio 19 GPIO_ACTIVE_HIGH /* sda */
			 &gpio 18 GPIO_ACTIVE_HIGH /* scl */
			>;
		#address-cells = <1>;
		#size-cells = <0>;

		i2c-gpio,scl-open-drain;
		i2c-gpio,sda-open-drain;

		tmp423a@4e {
			compatible = "ti,tmp423";
			reg = <0x4e>;
		};
	};

	watchdog {
		compatible = "linux,wdt-gpio";
		gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
		hw_algo = "toggle";
		/* hw_margin_ms is actually 300s but driver limits it to 60s */
		hw_margin_ms = <60000>;
		always-running;
	};

	gpio-export {
		compatible = "gpio-export";
		#size-cells = <0>;

		gpio_pa_dcdc {
			gpio-export,name = "om5pac:pa_dcdc";
			gpio-export,output = <1>;
			gpios = <&gpio 2 GPIO_ACTIVE_HIGH>;
		};
		gpio_pa_high {
			gpio-export,name = "om5pac:pa_high";
			gpio-export,output = <1>;
			gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
		};
	};
};

&pinmux {
	pinmux_pa_dcdc_pins {
		pinctrl-single,bits = <0x0 0x0 0xff0000>;
	};

	pinmux_pa_high_pins {
		pinctrl-single,bits = <0x10 0x0 0xff>;
	};
};

&pcie0 {
	status = "okay";
};

&spi {
	status = "okay";

	flash@0 {
		compatible = "jedec,spi-nor";
		reg = <0>;
		spi-max-frequency = <25000000>;

		/* partitions are passed via bootloader */
		partitions {
			compatible = "fixed-partitions";
			#address-cells = <1>;
			#size-cells = <1>;

			partition@0 {
				label = "u-boot";
				reg = <0x000000 0x040000>;
				read-only;
			};

			partition@40000 {
				label = "u-boot-env";
				reg = <0x040000 0x010000>;
			};

			partition@50000 {
				label = "custom";
				reg = <0x050000 0x060000>;
				read-only;
			};

			partition@b0000 {
				label = "inactive";
				reg = <0x0b0000 0x7a0000>;
			};

			partition@850000 {
				label = "inactive2";
				reg = <0x850000 0x7a0000>;
			};

			art: partition@ff0000 {
				label = "ART";
				reg = <0xff0000 0x010000>;
				read-only;
			};
		};
	};
};

&mdio0 {
	status = "okay";

	phy-mask = <0x10>;

	phy4: ethernet-phy@4 {
		reg = <4>;
		eee-broken-100tx;
		eee-broken-1000t;
	};
};

&mdio1 {
	status = "okay";

	phy-mask = <0x2>;

	phy1: ethernet-phy@1 {
		reg = <1>;
		eee-broken-100tx;
		eee-broken-1000t;
		at803x-override-sgmii-link-check;
	};
};

&eth0 {
	status = "okay";

	pll-data = <0x82000101 0x80000101 0x80001313>;

	mtd-mac-address = <&art 0x0>;

	phy-mode = "rgmii-id";
	phy-handle = <&phy4>;

	gmac-config {
		device = <&gmac>;
		rgmii-enabled = <1>;
		rxd-delay = <2>;
		rxdv-delay = <2>;
		txd-delay = <0>;
		txen-delay = <0>;
	};
};

&eth1 {
	status = "okay";

	pll-data = <0x03000101 0x80000101 0x80001313>;

	mtd-mac-address = <&art 0x6>;

	qca955x-sgmii-fixup;

	phy-handle = <&phy1>;
};

&wmac {
	status = "okay";

	mtd-cal-data = <&art 0x1000>;
	mtd-mac-address = <&art 0x0>;
	mac-address-increment = <2>;
};