target/linux/ipq806x/patches-5.4/083-ipq8064-dtsi-additions.patch

--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
@@ -8,6 +8,8 @@
 #include <dt-bindings/reset/qcom,gcc-ipq806x.h>
 #include <dt-bindings/soc/qcom,gsbi.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/mfd/qcom-rpm.h>
+#include <dt-bindings/clock/qcom,rpmcc.h>
 
 / {
 	#address-cells = <1>;
@@ -28,6 +30,16 @@
 			next-level-cache = <&L2>;
 			qcom,acc = <&acc0>;
 			qcom,saw = <&saw0>;
+			clocks = <&kraitcc 0>, <&kraitcc 4>;
+			clock-names = "cpu", "l2";
+			clock-latency = <100000>;
+			cpu-supply = <&smb208_s2a>;
+			operating-points-v2 = <&opp_table0>;
+			voltage-tolerance = <5>;
+			cooling-min-state = <0>;
+			cooling-max-state = <10>;
+			#cooling-cells = <2>;
+			cpu-idle-states = <&CPU_SPC>;
 		};
 
 		cpu1: cpu@1 {
@@ -38,11 +50,458 @@
 			next-level-cache = <&L2>;
 			qcom,acc = <&acc1>;
 			qcom,saw = <&saw1>;
+			clocks = <&kraitcc 1>, <&kraitcc 4>;
+			clock-names = "cpu", "l2";
+			clock-latency = <100000>;
+			cpu-supply = <&smb208_s2b>;
+			operating-points-v2 = <&opp_table0>;
+			voltage-tolerance = <5>;
+			cooling-min-state = <0>;
+			cooling-max-state = <10>;
+			#cooling-cells = <2>;
+			cpu-idle-states = <&CPU_SPC>;
 		};
 
 		L2: l2-cache {
 			compatible = "cache";
 			cache-level = <2>;
+			qcom,saw = <&saw_l2>;
+		};
+
+		qcom,l2 {
+			qcom,l2-rates = <384000000 1000000000 1200000000>;
+			qcom,l2-cpufreq = <384000000 600000000 1200000000>;
+			qcom,l2-volt = <1100000 1100000 1150000>;
+			qcom,l2-supply = <&smb208_s1a>;
+		};
+
+		idle-states {
+			CPU_SPC: spc {
+				compatible = "qcom,idle-state-spc", "arm,idle-state";
+				status = "disabled";
+				entry-latency-us = <400>;
+				exit-latency-us = <900>;
+				min-residency-us = <3000>;
+			};
+		};
+	};
+
+	opp_table0: opp_table0 {
+		compatible = "operating-points-v2-kryo-cpu";
+		nvmem-cells = <&speedbin_efuse>;
+
+		opp-384000000 {
+			opp-hz = /bits/ 64 <384000000>;
+			opp-microvolt-speed0-pvs0-v0 = <1000000>;
+			opp-microvolt-speed0-pvs1-v0 = <925000>;
+			opp-microvolt-speed0-pvs2-v0 = <875000>;
+			opp-microvolt-speed0-pvs3-v0 = <800000>;
+			opp-supported-hw = <0x1>;
+			clock-latency-ns = <100000>;
+		};
+
+		opp-600000000 {
+			opp-hz = /bits/ 64 <600000000>;
+			opp-microvolt-speed0-pvs0-v0 = <1050000>;
+			opp-microvolt-speed0-pvs1-v0 = <975000>;
+			opp-microvolt-speed0-pvs2-v0 = <925000>;
+			opp-microvolt-speed0-pvs3-v0 = <850000>;
+			opp-supported-hw = <0x1>;
+			clock-latency-ns = <100000>;
+		};
+
+		opp-800000000 {
+			opp-hz = /bits/ 64 <800000000>;
+			opp-microvolt-speed0-pvs0-v0 = <1100000>;
+			opp-microvolt-speed0-pvs1-v0 = <1025000>;
+			opp-microvolt-speed0-pvs2-v0 = <995000>;
+			opp-microvolt-speed0-pvs3-v0 = <900000>;
+			opp-supported-hw = <0x1>;
+			clock-latency-ns = <100000>;
+		};
+
+		opp-1000000000 {
+			opp-hz = /bits/ 64 <1000000000>;
+			opp-microvolt-speed0-pvs0-v0 = <1150000>;
+			opp-microvolt-speed0-pvs1-v0 = <1075000>;
+			opp-microvolt-speed0-pvs2-v0 = <1025000>;
+			opp-microvolt-speed0-pvs3-v0 = <950000>;
+			opp-supported-hw = <0x1>;
+			clock-latency-ns = <100000>;
+		};
+
+		opp-1200000000 {
+			opp-hz = /bits/ 64 <1200000000>;
+			opp-microvolt-speed0-pvs0-v0 = <1200000>;
+			opp-microvolt-speed0-pvs1-v0 = <1125000>;
+			opp-microvolt-speed0-pvs2-v0 = <1075000>;
+			opp-microvolt-speed0-pvs3-v0 = <1000000>;
+			opp-supported-hw = <0x1>;
+			clock-latency-ns = <100000>;
+		};
+
+		opp-1400000000 {
+			opp-hz = /bits/ 64 <1400000000>;
+			opp-microvolt-speed0-pvs0-v0 = <1250000>;
+			opp-microvolt-speed0-pvs1-v0 = <1175000>;
+			opp-microvolt-speed0-pvs2-v0 = <1125000>;
+			opp-microvolt-speed0-pvs3-v0 = <1050000>;
+			opp-supported-hw = <0x1>;
+			clock-latency-ns = <100000>;
+		};
+	};
+
+	thermal-zones {
+		tsens_tz_sensor0 {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 0>;
+
+			trips {
+				cpu-critical-hi {
+					temperature = <125000>;
+					hysteresis = <2000>;
+					type = "critical_high";
+				};
+
+				cpu-config-hi {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "configurable_hi";
+				};
+
+				cpu-config-lo {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "configurable_lo";
+				};
+
+				cpu-critical-low {
+					temperature = <0>;
+					hysteresis = <2000>;
+					type = "critical_low";
+				};
+			};
+		};
+
+		tsens_tz_sensor1 {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 1>;
+
+			trips {
+				cpu-critical-hi {
+					temperature = <125000>;
+					hysteresis = <2000>;
+					type = "critical_high";
+				};
+
+				cpu-config-hi {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "configurable_hi";
+				};
+
+				cpu-config-lo {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "configurable_lo";
+				};
+
+				cpu-critical-low {
+					temperature = <0>;
+					hysteresis = <2000>;
+					type = "critical_low";
+				};
+			};
+		};
+
+		tsens_tz_sensor2 {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 2>;
+
+			trips {
+				cpu-critical-hi {
+					temperature = <125000>;
+					hysteresis = <2000>;
+					type = "critical_high";
+				};
+
+				cpu-config-hi {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "configurable_hi";
+				};
+
+				cpu-config-lo {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "configurable_lo";
+				};
+
+				cpu-critical-low {
+					temperature = <0>;
+					hysteresis = <2000>;
+					type = "critical_low";
+				};
+			};
+		};
+
+		tsens_tz_sensor3 {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 3>;
+
+			trips {
+				cpu-critical-hi {
+					temperature = <125000>;
+					hysteresis = <2000>;
+					type = "critical_high";
+				};
+
+				cpu-config-hi {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "configurable_hi";
+				};
+
+				cpu-config-lo {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "configurable_lo";
+				};
+
+				cpu-critical-low {
+					temperature = <0>;
+					hysteresis = <2000>;
+					type = "critical_low";
+				};
+			};
+		};
+
+		tsens_tz_sensor4 {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 4>;
+
+			trips {
+				cpu-critical-hi {
+					temperature = <125000>;
+					hysteresis = <2000>;
+					type = "critical_high";
+				};
+
+				cpu-config-hi {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "configurable_hi";
+				};
+
+				cpu-config-lo {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "configurable_lo";
+				};
+
+				cpu-critical-low {
+					temperature = <0>;
+					hysteresis = <2000>;
+					type = "critical_low";
+				};
+			};
+		};
+
+		tsens_tz_sensor5 {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 5>;
+
+			trips {
+				cpu-critical-hi {
+					temperature = <125000>;
+					hysteresis = <2000>;
+					type = "critical_high";
+				};
+
+				cpu-config-hi {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "configurable_hi";
+				};
+
+				cpu-config-lo {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "configurable_lo";
+				};
+
+				cpu-critical-low {
+					temperature = <0>;
+					hysteresis = <2000>;
+					type = "critical_low";
+				};
+			};
+		};
+
+		tsens_tz_sensor6 {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 6>;
+
+			trips {
+				cpu-critical-hi {
+					temperature = <125000>;
+					hysteresis = <2000>;
+					type = "critical_high";
+				};
+
+				cpu-config-hi {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "configurable_hi";
+				};
+
+				cpu-config-lo {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "configurable_lo";
+				};
+
+				cpu-critical-low {
+					temperature = <0>;
+					hysteresis = <2000>;
+					type = "critical_low";
+				};
+			};
+		};
+
+		tsens_tz_sensor7 {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 7>;
+
+			trips {
+				cpu-critical-hi {
+					temperature = <125000>;
+					hysteresis = <2000>;
+					type = "critical_high";
+				};
+
+				cpu-config-hi {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "configurable_hi";
+				};
+
+				cpu-config-lo {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "configurable_lo";
+				};
+
+				cpu-critical-low {
+					temperature = <0>;
+					hysteresis = <2000>;
+					type = "critical_low";
+				};
+			};
+		};
+
+		tsens_tz_sensor8 {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 8>;
+
+			trips {
+				cpu-critical-hi {
+					temperature = <125000>;
+					hysteresis = <2000>;
+					type = "critical_high";
+				};
+
+				cpu-config-hi {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "configurable_hi";
+				};
+
+				cpu-config-lo {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "configurable_lo";
+				};
+
+				cpu-critical-low {
+					temperature = <0>;
+					hysteresis = <2000>;
+					type = "critical_low";
+				};
+			};
+		};
+
+		tsens_tz_sensor9 {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 9>;
+
+			trips {
+				cpu-critical-hi {
+					temperature = <125000>;
+					hysteresis = <2000>;
+					type = "critical_high";
+				};
+
+				cpu-config-hi {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "configurable_hi";
+				};
+
+				cpu-config-lo {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "configurable_lo";
+				};
+
+				cpu-critical-low {
+					temperature = <0>;
+					hysteresis = <2000>;
+					type = "critical_low";
+				};
+			};
+		};
+
+		tsens_tz_sensor10 {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 10>;
+
+			trips {
+				cpu-critical-hi {
+					temperature = <125000>;
+					hysteresis = <2000>;
+					type = "critical_high";
+				};
+
+				cpu-config-hi {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "configurable_hi";
+				};
+
+				cpu-config-lo {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "configurable_lo";
+				};
+
+				cpu-critical-low {
+					temperature = <0>;
+					hysteresis = <2000>;
+					type = "critical_low";
+				};
+			};
 		};
 	};
 
@@ -93,6 +552,15 @@
 		};
 	};
 
+	fab-scaling {
+		compatible = "qcom,fab-scaling";
+		clocks = <&rpmcc RPM_APPS_FABRIC_A_CLK>, <&rpmcc RPM_EBI1_A_CLK>;
+		clock-names = "apps-fab-clk", "ddr-fab-clk";
+		fab_freq_high = <533000000>;
+		fab_freq_nominal = <400000000>;
+		cpu_freq_threshold = <1000000000>;
+	};
+
 	firmware {
 		scm {
 			compatible = "qcom,scm-ipq806x", "qcom,scm";
@@ -120,6 +588,84 @@
 			reg-names = "lpass-lpaif";
 		};
 
+		qfprom: qfprom@700000 {
+			compatible = "qcom,qfprom", "syscon";
+			reg = <0x700000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "okay";
+			tsens_calib: calib@400 {
+				reg = <0x400 0xb>;
+			};
+			tsens_backup: backup@410 {
+				reg = <0x410 0xb>;
+			};
+			speedbin_efuse: speedbin@0c0 {
+				reg = <0x0c0 0x4>;
+			};
+		};
+
+		rpm: rpm@108000 {
+			compatible = "qcom,rpm-ipq8064";
+			reg = <0x108000 0x1000>;
+			qcom,ipc = <&l2cc 0x8 2>;
+
+			interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+					 <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+					 <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "ack", "err", "wakeup";
+
+			clocks = <&gcc RPM_MSG_RAM_H_CLK>;
+			clock-names = "ram";
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			rpmcc: clock-controller {
+				compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc";
+				#clock-cells = <1>;
+			};
+
+			regulators {
+				compatible = "qcom,rpm-smb208-regulators";
+
+				smb208_s1a: s1a {
+					regulator-min-microvolt = <1050000>;
+					regulator-max-microvolt = <1150000>;
+
+					qcom,switch-mode-frequency = <1200000>;
+				};
+
+				smb208_s1b: s1b {
+					regulator-min-microvolt = <1050000>;
+					regulator-max-microvolt = <1150000>;
+
+					qcom,switch-mode-frequency = <1200000>;
+				};
+
+				smb208_s2a: s2a {
+					regulator-min-microvolt = < 800000>;
+					regulator-max-microvolt = <1250000>;
+
+					qcom,switch-mode-frequency = <1200000>;
+				};
+
+				smb208_s2b: s2b {
+					regulator-min-microvolt = < 800000>;
+					regulator-max-microvolt = <1250000>;
+
+					qcom,switch-mode-frequency = <1200000>;
+				};
+			};
+		};
+
+		rng@1a500000 {
+			compatible = "qcom,prng";
+			reg = <0x1a500000 0x200>;
+			clocks = <&gcc PRNG_CLK>;
+			clock-names = "core";
+		};
+
 		qcom_pinmux: pinmux@800000 {
 			compatible = "qcom,ipq8064-pinctrl";
 			reg = <0x800000 0x4000>;
@@ -159,6 +705,15 @@
 				};
 			};
 
+			i2c4_pins: i2c4_pinmux {
+				mux {
+					pins = "gpio12", "gpio13";
+					function = "gsbi4";
+					drive-strength = <12>;
+					bias-disable;
+				};
+			};
+
 			spi_pins: spi_pins {
 				mux {
 					pins = "gpio18", "gpio19", "gpio21";
@@ -168,6 +723,53 @@
 				};
 			};
 
+			nand_pins: nand_pins {
+				disable {
+					pins = "gpio34", "gpio35", "gpio36",
+					       "gpio37", "gpio38";
+					function = "nand";
+					drive-strength = <10>;
+					bias-disable;
+				};
+
+				pullups {
+					pins = "gpio39";
+					function = "nand";
+					drive-strength = <10>;
+					bias-pull-up;
+				};
+
+				hold {
+					pins = "gpio40", "gpio41", "gpio42",
+					       "gpio43", "gpio44", "gpio45",
+					       "gpio46", "gpio47";
+					function = "nand";
+					drive-strength = <10>;
+					bias-bus-hold;
+				};
+			};
+
+			mdio0_pins: mdio0_pins {
+				mux {
+					pins = "gpio0", "gpio1";
+					function = "mdio";
+					drive-strength = <8>;
+					bias-disable;
+				};
+			};
+
+			rgmii2_pins: rgmii2_pins {
+				mux {
+					pins = "gpio27", "gpio28", "gpio29",
+					       "gpio30", "gpio31", "gpio32",
+					       "gpio51", "gpio52", "gpio59",
+					       "gpio60", "gpio61", "gpio62";
+					function = "rgmii2";
+					drive-strength = <8>;
+					bias-disable;
+				};
+			};
+
 			leds_pins: leds_pins {
 				mux {
 					pins = "gpio7", "gpio8", "gpio9",
@@ -229,6 +831,17 @@
 			clock-output-names = "acpu1_aux";
 		};
 
+		l2cc: clock-controller@2011000 {
+			compatible = "qcom,kpss-gcc", "syscon";
+			reg = <0x2011000 0x1000>;
+			clock-output-names = "acpu_l2_aux";
+		};
+
+		kraitcc: clock-controller {
+			compatible = "qcom,krait-cc-v1";
+			#clock-cells = <1>;
+		};
+
 		saw0: regulator@2089000 {
 			compatible = "qcom,saw2", "qcom,apq8064-saw2-v1.1-cpu", "syscon";
 			reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
@@ -241,6 +854,17 @@
 			regulator;
 		};
 
+		saw_l2: regulator@02012000 {
+			compatible = "qcom,saw2", "syscon";
+			reg = <0x02012000 0x1000>;
+			regulator;
+		};
+
+		sic_non_secure: sic-non-secure@12100000 {
+			compatible = "syscon";
+			reg = <0x12100000 0x10000>;
+		};
+
 		gsbi2: gsbi@12480000 {
 			compatible = "qcom,gsbi-v1.0.0";
 			cell-index = <2>;
@@ -436,6 +1060,15 @@
 			#power-domain-cells = <1>;
 		};
 
+		tsens: thermal-sensor@900000 {
+			compatible = "qcom,ipq8064-tsens";
+			reg = <0x900000 0x3680>;
+			nvmem-cells = <&tsens_calib>, <&tsens_backup>;
+			nvmem-cell-names = "calib", "calib_backup";
+			interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
+			#thermal-sensor-cells = <1>;
+		};
+
 		tcsr: syscon@1a400000 {
 			compatible = "qcom,tcsr-ipq8064", "syscon";
 			reg = <0x1a400000 0x100>;
@@ -448,6 +1081,95 @@
 			#reset-cells = <1>;
 		};
 
+		sfpb_mutex_block: syscon@1200600 {
+			compatible = "syscon";
+			reg = <0x01200600 0x100>;
+		};
+
+		hs_phy_0: hs_phy_0 {
+			compatible = "qcom,ipq806x-usb-phy-hs";
+			reg = <0x110f8800 0x30>;
+			clocks = <&gcc USB30_0_UTMI_CLK>;
+			clock-names = "ref";
+			#phy-cells = <0>;
+		};
+
+		ss_phy_0: ss_phy_0 {
+			compatible = "qcom,ipq806x-usb-phy-ss";
+			reg = <0x110f8830 0x30>;
+			clocks = <&gcc USB30_0_MASTER_CLK>;
+			clock-names = "ref";
+			#phy-cells = <0>;
+		};
+
+		usb3_0: usb3@110f8800 {
+			compatible = "qcom,dwc3", "syscon";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x110f8800 0x8000>;
+			clocks = <&gcc USB30_0_MASTER_CLK>;
+			clock-names = "core";
+
+			ranges;
+
+			resets = <&gcc USB30_0_MASTER_RESET>;
+			reset-names = "master";
+
+			status = "disabled";
+
+			dwc3_0: dwc3@11000000 {
+				compatible = "snps,dwc3";
+				reg = <0x11000000 0xcd00>;
+				interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+				phys = <&hs_phy_0>, <&ss_phy_0>;
+				phy-names = "usb2-phy", "usb3-phy";
+				dr_mode = "host";
+				snps,dis_u3_susphy_quirk;
+			};
+		};
+
+		hs_phy_1: hs_phy_1 {
+			compatible = "qcom,ipq806x-usb-phy-hs";
+			reg = <0x100f8800 0x30>;
+			clocks = <&gcc USB30_1_UTMI_CLK>;
+			clock-names = "ref";
+			#phy-cells = <0>;
+		};
+
+		ss_phy_1: ss_phy_1 {
+			compatible = "qcom,ipq806x-usb-phy-ss";
+			reg = <0x100f8830 0x30>;
+			clocks = <&gcc USB30_1_MASTER_CLK>;
+			clock-names = "ref";
+			#phy-cells = <0>;
+		};
+
+		usb3_1: usb3@100f8800 {
+			compatible = "qcom,dwc3", "syscon";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x100f8800 0x8000>;
+			clocks = <&gcc USB30_1_MASTER_CLK>;
+			clock-names = "core";
+
+			ranges;
+
+			resets = <&gcc USB30_1_MASTER_RESET>;
+			reset-names = "master";
+
+			status = "disabled";
+
+			dwc3_1: dwc3@10000000 {
+				compatible = "snps,dwc3";
+				reg = <0x10000000 0xcd00>;
+				interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>;
+				phys = <&hs_phy_1>, <&ss_phy_1>;
+				phy-names = "usb2-phy", "usb3-phy";
+				dr_mode = "host";
+				snps,dis_u3_susphy_quirk;
+			};
+		};
+
 		pcie0: pci@1b500000 {
 			compatible = "qcom,pcie-ipq8064";
 			reg = <0x1b500000 0x1000
@@ -601,6 +1323,167 @@
 			perst-gpio = <&qcom_pinmux 63 GPIO_ACTIVE_LOW>;
 		};
 
+		adm_dma: dma@18300000 {
+			compatible = "qcom,adm";
+			reg = <0x18300000 0x100000>;
+			interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+
+			clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>;
+			clock-names = "core", "iface";
+
+			resets = <&gcc ADM0_RESET>,
+				 <&gcc ADM0_PBUS_RESET>,
+				 <&gcc ADM0_C0_RESET>,
+				 <&gcc ADM0_C1_RESET>,
+				 <&gcc ADM0_C2_RESET>;
+			reset-names = "clk", "pbus", "c0", "c1", "c2";
+			qcom,ee = <0>;
+
+			status = "disabled";
+		};
+
+		nand_controller: nand-controller@1ac00000 {
+			compatible = "qcom,ipq806x-nand";
+			reg = <0x1ac00000 0x800>;
+
+			clocks = <&gcc EBI2_CLK>,
+				 <&gcc EBI2_AON_CLK>;
+			clock-names = "core", "aon";
+
+			dmas = <&adm_dma 3>;
+			dma-names = "rxtx";
+			qcom,cmd-crci = <15>;
+			qcom,data-crci = <3>;
+
+			status = "disabled";
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		nss_common: syscon@03000000 {
+			compatible = "syscon";
+			reg = <0x03000000 0x0000FFFF>;
+		};
+
+		qsgmii_csr: syscon@1bb00000 {
+			compatible = "syscon";
+			reg = <0x1bb00000 0x000001FF>;
+		};
+
+		stmmac_axi_setup: stmmac-axi-config {
+			snps,wr_osr_lmt = <7>;
+			snps,rd_osr_lmt = <7>;
+			snps,blen = <16 0 0 0 0 0 0>;
+		};
+
+		mdio0: mdio@37000000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			compatible = "qcom,ipq8064-mdio", "syscon";
+			reg = <0x37000000 0x200000>;
+			resets = <&gcc GMAC_CORE1_RESET>;
+			reset-names = "stmmaceth";
+			clocks = <&gcc GMAC_CORE1_CLK>;
+			clock-names = "stmmaceth";
+
+			status = "disabled";
+		};
+
+		gmac0: ethernet@37000000 {
+			device_type = "network";
+			compatible = "qcom,ipq806x-gmac";
+			reg = <0x37000000 0x200000>;
+			interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+
+			snps,axi-config = <&stmmac_axi_setup>;
+			snps,pbl = <32>;
+			snps,aal = <1>;
+
+			qcom,nss-common = <&nss_common>;
+			qcom,qsgmii-csr = <&qsgmii_csr>;
+
+			clocks = <&gcc GMAC_CORE1_CLK>;
+			clock-names = "stmmaceth";
+
+			resets = <&gcc GMAC_CORE1_RESET>;
+			reset-names = "stmmaceth";
+
+			status = "disabled";
+		};
+
+		gmac1: ethernet@37200000 {
+			device_type = "network";
+			compatible = "qcom,ipq806x-gmac";
+			reg = <0x37200000 0x200000>;
+			interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+
+			snps,axi-config = <&stmmac_axi_setup>;
+			snps,pbl = <32>;
+			snps,aal = <1>;
+
+			qcom,nss-common = <&nss_common>;
+			qcom,qsgmii-csr = <&qsgmii_csr>;
+
+			clocks = <&gcc GMAC_CORE2_CLK>;
+			clock-names = "stmmaceth";
+
+			resets = <&gcc GMAC_CORE2_RESET>;
+			reset-names = "stmmaceth";
+
+			status = "disabled";
+		};
+
+		gmac2: ethernet@37400000 {
+			device_type = "network";
+			compatible = "qcom,ipq806x-gmac", "snps,dwmac";
+			reg = <0x37400000 0x200000>;
+			interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+
+			snps,axi-config = <&stmmac_axi_setup>;
+			snps,pbl = <32>;
+			snps,aal = <1>;
+
+			qcom,nss-common = <&nss_common>;
+			qcom,qsgmii-csr = <&qsgmii_csr>;
+
+			clocks = <&gcc GMAC_CORE3_CLK>;
+			clock-names = "stmmaceth";
+
+			resets = <&gcc GMAC_CORE3_RESET>;
+			reset-names = "stmmaceth";
+
+			status = "disabled";
+		};
+
+		gmac3: ethernet@37600000 {
+			device_type = "network";
+			compatible = "qcom,ipq806x-gmac", "snps,dwmac";
+			reg = <0x37600000 0x200000>;
+			interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+
+			snps,axi-config = <&stmmac_axi_setup>;
+			snps,pbl = <32>;
+			snps,aal = <1>;
+
+			qcom,nss-common = <&nss_common>;
+			qcom,qsgmii-csr = <&qsgmii_csr>;
+
+			clocks = <&gcc GMAC_CORE4_CLK>;
+			clock-names = "stmmaceth";
+
+			resets = <&gcc GMAC_CORE4_RESET>;
+			reset-names = "stmmaceth";
+
+			status = "disabled";
+		};
+
 		vsdcc_fixed: vsdcc-regulator {
 			compatible = "regulator-fixed";
 			regulator-name = "SDCC Power";
@@ -676,4 +1559,17 @@
 			};
 		};
 	};
+
+	sfpb_mutex: sfpb-mutex {
+		compatible = "qcom,sfpb-mutex";
+		syscon = <&sfpb_mutex_block 4 4>;
+
+		#hwlock-cells = <1>;
+	};
+
+	smem {
+		compatible = "qcom,smem";
+		memory-region = <&smem>;
+		hwlocks = <&sfpb_mutex 3>;
+	};
 };