mbtk/rootfs/etc/init.d/mbtk_boot_eary

#!/bin/sh

#MBTK_ADB=`getprop persist.mbtk.adb 2> /dev/null`
project=`cat /etc/mbtk_project`

mbtk_start() {
	echo "start : $1" > /dev/kmsg
	
	DEBUG_ENABLE=`getprop persist.mbtk.appdump 2> /dev/null`
	if [ "$DEBUG_ENABLE" == "1" ];then
		ulimit -c unlimited
	fi
	
	if [ -e $1 ];then
		# stdout and stderr > /dev/null
		#$@ &> /dev/null &
		(while ! $@ &> /dev/null;           do echo "Restarting $@ ...";               done) &
	fi
}

start_service() {
	echo "--mbtk eary boot start--" > /dev/kmsg
#	mbtk_start /bin/mbtk_test
#	mbtk_start /bin/mbtk_test "eary" 123
    # ɾ³ýÉÏ´Îgnss ÐÇÀú
    if [ -f /etc/mbtk/rtm.bin ]
    then
	    echo "--mbtk eary boot rtm.bin " > /dev/kmsg
        rm /etc/mbtk/rtm.bin
    fi

	mbtk_start /bin/mbtk_rild
	uci set persist.mbtk.sdk__state='-1'
	if [ -f /bin/mbtk_sdk_ready ]
	then
		mbtk_start /bin/mbtk_sdk_ready
		echo "--mbtk platform mbtk_sdk_ready start--" > /dev/kmsg
	fi

	if [ "$project" == "T108_2" ];then
		i2cset -y -f 2 0x31 0x15 0x00
		[ -e /bin/mbtk_gnssd ] && mbtk_start /bin/mbtk_gnssd 8122 /dev/ttyS3 0
	elif [ "$project" == "L508_X6" ];then
		[ -e /bin/mbtk_gnssd ] && mbtk_start /bin/mbtk_gnssd 5311 /dev/ttyS3 255
	else
		# Only auto open gnss but not open any port.
		[ -e /bin/mbtk_gnssd ] && mbtk_start /bin/mbtk_gnssd 5311 /dev/ttyS2 255
	fi

	if [ "$project" == "L508_X6" -o "$project" == "L509" ]
	then
		#echo "$project"
		i2cset -y -f 2 0x32 0x0d 0x00
	fi
	echo "--mbtk eary boot end--" > /dev/kmsg
}

sleep_init()
{
	if [ -e /sys/devices/soc.0/d4000000.apb/mbtk-dev-op/gps_power ]
	then
		echo off  > /sys/devices/soc.0/d4000000.apb/mbtk-dev-op/gps_power
	else
		echo "/sys/devices/soc.0/d4000000.apb/mbtk-dev-op/gps_power can not write." > /dev/kmsg
	fi
	
	if [ -e /sys/kernel/debug/spk_shdn_gpio ]
	then
		echo 0 > /sys/kernel/debug/spk_shdn_gpio
	else
		echo "/sys/kernel/debug/spk_shdn_gpio can not write." > /dev/kmsg
	fi
	
	if [ -e /sys/devices/asr-rfkill.0/pwr_ctrl ]
	then
		echo 1 > /sys/devices/asr-rfkill.0/pwr_ctrl
		sleep 1
		echo 0 > /sys/devices/asr-rfkill.0/pwr_ctrl
	else
		echo "/sys/devices/asr-rfkill.0/pwr_ctrl can not write." > /dev/kmsg
	fi

	case "$project" in
		PN1803)
			echo 4 > /sys/class/gpio/export
			echo out > /sys/class/gpio/gpio4/direction
			echo 0 > /sys/class/gpio/gpio4/value
			;;
		L509)
			echo 5 > /sys/class/gpio/export
			echo out > /sys/class/gpio/gpio5/direction
			echo 0 > /sys/class/gpio/gpio5/value
			
			echo 8 > /sys/class/gpio/export
			echo out > /sys/class/gpio/gpio8/direction
			echo 1 > /sys/class/gpio/gpio8/value
			;;
	esac
	
	if [ "$project" == "PN1803" -o "$project" == "L508" -o "$project" == "L509"]
	then
		echo 118 > /sys/class/gpio/export
		echo out > /sys/class/gpio/gpio118/direction
		echo 0 > /sys/class/gpio/gpio118/value
	fi
}

start_service
sleep_init