| b.liu | e958203 | 2025-04-17 19:18:16 +0800 | [diff] [blame] | 1 | #!/bin/bash |
| 2 | # |
| 3 | # tftp flash script for wireless routers |
| 4 | # |
| 5 | # Copyright (C) 2004 by Oleg I. Vdovikin <oleg@cs.msu.su> |
| 6 | # Copyright (C) 2005 by Waldemar Brodkorb <wbx@openwrt.org> |
| 7 | # |
| 8 | # This program is free software; you can redistribute it and/or modify |
| 9 | # it under the terms of the GNU General Public License as published by |
| 10 | # the Free Software Foundation; either version 2 of the License, or |
| 11 | # (at your option) any later version. |
| 12 | # |
| 13 | # This program is distributed in the hope that it will be useful, |
| 14 | # but WITHOUT ANY WARRANTY; without even the implied warranty of |
| 15 | # MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU |
| 16 | # General Public License for more details. |
| 17 | # |
| 18 | # You should have received a copy of the GNU General Public License |
| 19 | # along with this program; if not, write to the Free Software |
| 20 | # Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA |
| 21 | # |
| 22 | |
| 23 | if [ -z "$1" ] || [ ! -f "$1" ] || [ -z "$2" ]; then |
| 24 | echo Usage: "$0" firmware vendor |
| 25 | cat << EOF |
| 26 | IMPORTANT: |
| 27 | Notes for Linksys / Asus WL500gx router: |
| 28 | be sure you have set boot_wait to yes. Power on your router |
| 29 | after executing this script. |
| 30 | |
| 31 | Notes for Asus WL500g router: |
| 32 | be sure POWER led is flashing (If this is not the case |
| 33 | poweroff the device, push the reset button & power on |
| 34 | it again, then release button) |
| 35 | |
| 36 | 1) connect your pc to the LAN port |
| 37 | 2) be sure your link is up and has an address in the |
| 38 | 192.168.1.0/24 address range (and not the 192.168.1.1) |
| 39 | |
| 40 | Notes for Toshiba router: |
| 41 | boot_wait is enabled by default on these units. |
| 42 | |
| 43 | 1) connect your pc to any of the four LAN ports |
| 44 | 2) be sure your link is up and has an address in the |
| 45 | 192.168.10.1/24 address range (and not the 192.168.10.1) |
| 46 | 3) run this script (unit will only accept .trx images) |
| 47 | 4) Turn unit power on. |
| 48 | |
| 49 | EOF |
| 50 | exit 0 |
| 51 | fi |
| 52 | if [ "$2" = "asus" ]; then |
| 53 | echo Confirming IP address setting... |
| 54 | echo -en "get ASUSSPACELINK\x01\x01\xa8\xc0 /dev/null\nquit\n" | tftp 192.168.1.1 |
| 55 | echo Flashing 192.168.1.1 using "$1"... |
| 56 | echo -en "binary\nput $1 ASUSSPACELINK\nquit\n" | tftp 192.168.1.1 |
| 57 | echo Please wait until leds stops flashing. |
| 58 | elif [ "$2" = "linksys" ]; then |
| 59 | echo Flashing 192.168.1.1 using "$1"... |
| 60 | echo -en "rexmt 1\ntrace\nbinary\nput $1\nquit\n" | tftp 192.168.1.1 |
| 61 | echo Please wait until power led stops flashing. Do not poweroff! Then you can login via telnet 192.168.1.1. |
| 62 | elif [ "$2" = "toshiba" ]; then |
| 63 | echo Flashing 192.168.10.1 using "$1"... |
| 64 | echo -en "rexmt 1\ntrace\nbinary\nput $1\nquit\n" | tftp 192.168.10.1 |
| 65 | echo Unit will automatically reboot within 5 minutes. Do not power off. Then you can login via telnet 192.168.10.1. |
| 66 | fi |