| b.liu | e958203 | 2025-04-17 19:18:16 +0800 | [diff] [blame] | 1 | // SPDX-License-Identifier: GPL-2.0 |
| 2 | #include "qcom-ipq8064.dtsi" |
| 3 | #include <dt-bindings/input/input.h> |
| 4 | |
| 5 | / { |
| 6 | model = "Qualcomm Technologies, Inc. IPQ8064-v1.0"; |
| 7 | |
| 8 | aliases { |
| 9 | serial0 = &gsbi4_serial; |
| 10 | }; |
| 11 | |
| 12 | chosen { |
| 13 | stdout-path = "serial0:115200n8"; |
| 14 | }; |
| 15 | |
| 16 | soc { |
| 17 | gsbi@16300000 { |
| 18 | qcom,mode = <GSBI_PROT_I2C_UART>; |
| 19 | status = "ok"; |
| 20 | |
| 21 | serial@16340000 { |
| 22 | status = "ok"; |
| 23 | }; |
| 24 | }; |
| 25 | |
| 26 | gsbi5: gsbi@1a200000 { |
| 27 | qcom,mode = <GSBI_PROT_SPI>; |
| 28 | status = "ok"; |
| 29 | |
| 30 | spi4: spi@1a280000 { |
| 31 | status = "ok"; |
| 32 | spi-max-frequency = <50000000>; |
| 33 | |
| 34 | pinctrl-0 = <&spi_pins>; |
| 35 | pinctrl-names = "default"; |
| 36 | |
| 37 | cs-gpios = <&qcom_pinmux 20 0>; |
| 38 | |
| 39 | flash: m25p80@0 { |
| 40 | compatible = "s25fl256s1"; |
| 41 | #address-cells = <1>; |
| 42 | #size-cells = <1>; |
| 43 | spi-max-frequency = <50000000>; |
| 44 | reg = <0>; |
| 45 | |
| 46 | partition@0 { |
| 47 | label = "rootfs"; |
| 48 | reg = <0x0 0x1000000>; |
| 49 | }; |
| 50 | |
| 51 | partition@1 { |
| 52 | label = "scratch"; |
| 53 | reg = <0x1000000 0x1000000>; |
| 54 | }; |
| 55 | }; |
| 56 | }; |
| 57 | }; |
| 58 | |
| 59 | sata-phy@1b400000 { |
| 60 | status = "ok"; |
| 61 | }; |
| 62 | |
| 63 | sata@29000000 { |
| 64 | ports-implemented = <0x1>; |
| 65 | status = "ok"; |
| 66 | }; |
| 67 | |
| 68 | gpio_keys { |
| 69 | compatible = "gpio-keys"; |
| 70 | pinctrl-0 = <&buttons_pins>; |
| 71 | pinctrl-names = "default"; |
| 72 | |
| 73 | button@1 { |
| 74 | label = "reset"; |
| 75 | linux,code = <KEY_RESTART>; |
| 76 | gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; |
| 77 | linux,input-type = <1>; |
| 78 | debounce-interval = <60>; |
| 79 | }; |
| 80 | button@2 { |
| 81 | label = "wps"; |
| 82 | linux,code = <KEY_WPS_BUTTON>; |
| 83 | gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; |
| 84 | linux,input-type = <1>; |
| 85 | debounce-interval = <60>; |
| 86 | }; |
| 87 | }; |
| 88 | |
| 89 | leds { |
| 90 | compatible = "gpio-leds"; |
| 91 | pinctrl-0 = <&leds_pins>; |
| 92 | pinctrl-names = "default"; |
| 93 | |
| 94 | led@7 { |
| 95 | label = "led_usb1"; |
| 96 | gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; |
| 97 | linux,default-trigger = "usbdev"; |
| 98 | default-state = "off"; |
| 99 | }; |
| 100 | |
| 101 | led@8 { |
| 102 | label = "led_usb3"; |
| 103 | gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; |
| 104 | linux,default-trigger = "usbdev"; |
| 105 | default-state = "off"; |
| 106 | }; |
| 107 | |
| 108 | led@9 { |
| 109 | label = "status_led_fail"; |
| 110 | gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; |
| 111 | default-state = "off"; |
| 112 | }; |
| 113 | |
| 114 | led@26 { |
| 115 | label = "sata_led"; |
| 116 | gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; |
| 117 | default-state = "off"; |
| 118 | }; |
| 119 | |
| 120 | led@53 { |
| 121 | label = "status_led_pass"; |
| 122 | gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; |
| 123 | default-state = "off"; |
| 124 | }; |
| 125 | }; |
| 126 | }; |
| 127 | }; |