| b.liu | e958203 | 2025-04-17 19:18:16 +0800 | [diff] [blame^] | 1 | // SPDX-License-Identifier: GPL-2.0 |
| 2 | #include "qcom-msm8974.dtsi" |
| 3 | #include "qcom-pm8841.dtsi" |
| 4 | #include "qcom-pm8941.dtsi" |
| 5 | #include <dt-bindings/gpio/gpio.h> |
| 6 | #include <dt-bindings/input/input.h> |
| 7 | #include <dt-bindings/pinctrl/qcom,pmic-gpio.h> |
| 8 | |
| 9 | / { |
| 10 | model = "LGE MSM 8974 HAMMERHEAD"; |
| 11 | compatible = "lge,hammerhead", "qcom,msm8974"; |
| 12 | |
| 13 | aliases { |
| 14 | serial0 = &blsp1_uart1; |
| 15 | }; |
| 16 | |
| 17 | chosen { |
| 18 | stdout-path = "serial0:115200n8"; |
| 19 | }; |
| 20 | |
| 21 | smd { |
| 22 | rpm { |
| 23 | rpm_requests { |
| 24 | pm8841-regulators { |
| 25 | s1 { |
| 26 | regulator-min-microvolt = <675000>; |
| 27 | regulator-max-microvolt = <1050000>; |
| 28 | }; |
| 29 | |
| 30 | s2 { |
| 31 | regulator-min-microvolt = <500000>; |
| 32 | regulator-max-microvolt = <1050000>; |
| 33 | }; |
| 34 | |
| 35 | s3 { |
| 36 | regulator-min-microvolt = <1050000>; |
| 37 | regulator-max-microvolt = <1050000>; |
| 38 | }; |
| 39 | |
| 40 | s4 { |
| 41 | regulator-min-microvolt = <815000>; |
| 42 | regulator-max-microvolt = <900000>; |
| 43 | }; |
| 44 | }; |
| 45 | |
| 46 | pm8941-regulators { |
| 47 | vdd_l1_l3-supply = <&pm8941_s1>; |
| 48 | vdd_l2_lvs1_2_3-supply = <&pm8941_s3>; |
| 49 | vdd_l4_l11-supply = <&pm8941_s1>; |
| 50 | vdd_l5_l7-supply = <&pm8941_s2>; |
| 51 | vdd_l6_l12_l14_l15-supply = <&pm8941_s2>; |
| 52 | vdd_l8_l16_l18_l19-supply = <&vreg_vph_pwr>; |
| 53 | vdd_l9_l10_l17_l22-supply = <&vreg_boost>; |
| 54 | vdd_l13_l20_l23_l24-supply = <&vreg_boost>; |
| 55 | vdd_l21-supply = <&vreg_boost>; |
| 56 | |
| 57 | s1 { |
| 58 | regulator-min-microvolt = <1300000>; |
| 59 | regulator-max-microvolt = <1300000>; |
| 60 | |
| 61 | regulator-always-on; |
| 62 | regulator-boot-on; |
| 63 | }; |
| 64 | |
| 65 | s2 { |
| 66 | regulator-min-microvolt = <2150000>; |
| 67 | regulator-max-microvolt = <2150000>; |
| 68 | |
| 69 | regulator-boot-on; |
| 70 | }; |
| 71 | |
| 72 | s3 { |
| 73 | regulator-min-microvolt = <1800000>; |
| 74 | regulator-max-microvolt = <1800000>; |
| 75 | |
| 76 | regulator-always-on; |
| 77 | regulator-boot-on; |
| 78 | }; |
| 79 | |
| 80 | l1 { |
| 81 | regulator-min-microvolt = <1225000>; |
| 82 | regulator-max-microvolt = <1225000>; |
| 83 | |
| 84 | regulator-always-on; |
| 85 | regulator-boot-on; |
| 86 | }; |
| 87 | |
| 88 | l2 { |
| 89 | regulator-min-microvolt = <1200000>; |
| 90 | regulator-max-microvolt = <1200000>; |
| 91 | }; |
| 92 | |
| 93 | l3 { |
| 94 | regulator-min-microvolt = <1225000>; |
| 95 | regulator-max-microvolt = <1225000>; |
| 96 | }; |
| 97 | |
| 98 | l4 { |
| 99 | regulator-min-microvolt = <1225000>; |
| 100 | regulator-max-microvolt = <1225000>; |
| 101 | }; |
| 102 | |
| 103 | l5 { |
| 104 | regulator-min-microvolt = <1800000>; |
| 105 | regulator-max-microvolt = <1800000>; |
| 106 | }; |
| 107 | |
| 108 | l6 { |
| 109 | regulator-min-microvolt = <1800000>; |
| 110 | regulator-max-microvolt = <1800000>; |
| 111 | |
| 112 | regulator-boot-on; |
| 113 | }; |
| 114 | |
| 115 | l7 { |
| 116 | regulator-min-microvolt = <1800000>; |
| 117 | regulator-max-microvolt = <1800000>; |
| 118 | |
| 119 | regulator-boot-on; |
| 120 | }; |
| 121 | |
| 122 | l8 { |
| 123 | regulator-min-microvolt = <1800000>; |
| 124 | regulator-max-microvolt = <1800000>; |
| 125 | }; |
| 126 | |
| 127 | l9 { |
| 128 | regulator-min-microvolt = <1800000>; |
| 129 | regulator-max-microvolt = <2950000>; |
| 130 | }; |
| 131 | |
| 132 | l10 { |
| 133 | regulator-min-microvolt = <1800000>; |
| 134 | regulator-max-microvolt = <2950000>; |
| 135 | }; |
| 136 | |
| 137 | l11 { |
| 138 | regulator-min-microvolt = <1300000>; |
| 139 | regulator-max-microvolt = <1300000>; |
| 140 | }; |
| 141 | |
| 142 | l12 { |
| 143 | regulator-min-microvolt = <1800000>; |
| 144 | regulator-max-microvolt = <1800000>; |
| 145 | |
| 146 | regulator-always-on; |
| 147 | regulator-boot-on; |
| 148 | }; |
| 149 | |
| 150 | l13 { |
| 151 | regulator-min-microvolt = <1800000>; |
| 152 | regulator-max-microvolt = <2950000>; |
| 153 | |
| 154 | regulator-boot-on; |
| 155 | }; |
| 156 | |
| 157 | l14 { |
| 158 | regulator-min-microvolt = <1800000>; |
| 159 | regulator-max-microvolt = <1800000>; |
| 160 | }; |
| 161 | |
| 162 | l15 { |
| 163 | regulator-min-microvolt = <2050000>; |
| 164 | regulator-max-microvolt = <2050000>; |
| 165 | }; |
| 166 | |
| 167 | l16 { |
| 168 | regulator-min-microvolt = <2700000>; |
| 169 | regulator-max-microvolt = <2700000>; |
| 170 | }; |
| 171 | |
| 172 | l17 { |
| 173 | regulator-min-microvolt = <2850000>; |
| 174 | regulator-max-microvolt = <2850000>; |
| 175 | }; |
| 176 | |
| 177 | l18 { |
| 178 | regulator-min-microvolt = <2850000>; |
| 179 | regulator-max-microvolt = <2850000>; |
| 180 | }; |
| 181 | |
| 182 | l19 { |
| 183 | regulator-min-microvolt = <3000000>; |
| 184 | regulator-max-microvolt = <3300000>; |
| 185 | }; |
| 186 | |
| 187 | l20 { |
| 188 | regulator-min-microvolt = <2950000>; |
| 189 | regulator-max-microvolt = <2950000>; |
| 190 | |
| 191 | regulator-boot-on; |
| 192 | regulator-system-load = <200000>; |
| 193 | regulator-allow-set-load; |
| 194 | }; |
| 195 | |
| 196 | l21 { |
| 197 | regulator-min-microvolt = <2950000>; |
| 198 | regulator-max-microvolt = <2950000>; |
| 199 | |
| 200 | regulator-boot-on; |
| 201 | }; |
| 202 | |
| 203 | l22 { |
| 204 | regulator-min-microvolt = <3000000>; |
| 205 | regulator-max-microvolt = <3300000>; |
| 206 | }; |
| 207 | |
| 208 | l23 { |
| 209 | regulator-min-microvolt = <3000000>; |
| 210 | regulator-max-microvolt = <3000000>; |
| 211 | }; |
| 212 | |
| 213 | l24 { |
| 214 | regulator-min-microvolt = <3075000>; |
| 215 | regulator-max-microvolt = <3075000>; |
| 216 | |
| 217 | regulator-boot-on; |
| 218 | }; |
| 219 | }; |
| 220 | }; |
| 221 | }; |
| 222 | }; |
| 223 | |
| 224 | vreg_wlan: wlan-regulator { |
| 225 | compatible = "regulator-fixed"; |
| 226 | |
| 227 | regulator-name = "wl-reg"; |
| 228 | regulator-min-microvolt = <3300000>; |
| 229 | regulator-max-microvolt = <3300000>; |
| 230 | |
| 231 | gpio = <&msmgpio 26 GPIO_ACTIVE_HIGH>; |
| 232 | enable-active-high; |
| 233 | |
| 234 | pinctrl-names = "default"; |
| 235 | pinctrl-0 = <&wlan_regulator_pin>; |
| 236 | }; |
| 237 | }; |
| 238 | |
| 239 | &soc { |
| 240 | serial@f991d000 { |
| 241 | status = "ok"; |
| 242 | }; |
| 243 | |
| 244 | pinctrl@fd510000 { |
| 245 | sdhc1_pin_a: sdhc1-pin-active { |
| 246 | clk { |
| 247 | pins = "sdc1_clk"; |
| 248 | drive-strength = <16>; |
| 249 | bias-disable; |
| 250 | }; |
| 251 | |
| 252 | cmd-data { |
| 253 | pins = "sdc1_cmd", "sdc1_data"; |
| 254 | drive-strength = <10>; |
| 255 | bias-pull-up; |
| 256 | }; |
| 257 | }; |
| 258 | |
| 259 | sdhc2_pin_a: sdhc2-pin-active { |
| 260 | clk { |
| 261 | pins = "sdc2_clk"; |
| 262 | drive-strength = <6>; |
| 263 | bias-disable; |
| 264 | }; |
| 265 | |
| 266 | cmd-data { |
| 267 | pins = "sdc2_cmd", "sdc2_data"; |
| 268 | drive-strength = <6>; |
| 269 | bias-pull-up; |
| 270 | }; |
| 271 | }; |
| 272 | |
| 273 | i2c1_pins: i2c1 { |
| 274 | mux { |
| 275 | pins = "gpio2", "gpio3"; |
| 276 | function = "blsp_i2c1"; |
| 277 | |
| 278 | drive-strength = <2>; |
| 279 | bias-disable; |
| 280 | }; |
| 281 | }; |
| 282 | |
| 283 | i2c2_pins: i2c2 { |
| 284 | mux { |
| 285 | pins = "gpio6", "gpio7"; |
| 286 | function = "blsp_i2c2"; |
| 287 | |
| 288 | drive-strength = <2>; |
| 289 | bias-disable; |
| 290 | }; |
| 291 | }; |
| 292 | |
| 293 | i2c3_pins: i2c3 { |
| 294 | mux { |
| 295 | pins = "gpio10", "gpio11"; |
| 296 | function = "blsp_i2c3"; |
| 297 | drive-strength = <2>; |
| 298 | bias-disable; |
| 299 | }; |
| 300 | }; |
| 301 | |
| 302 | i2c11_pins: i2c11 { |
| 303 | mux { |
| 304 | pins = "gpio83", "gpio84"; |
| 305 | function = "blsp_i2c11"; |
| 306 | |
| 307 | drive-strength = <2>; |
| 308 | bias-disable; |
| 309 | }; |
| 310 | }; |
| 311 | |
| 312 | i2c12_pins: i2c12 { |
| 313 | mux { |
| 314 | pins = "gpio87", "gpio88"; |
| 315 | function = "blsp_i2c12"; |
| 316 | drive-strength = <2>; |
| 317 | bias-disable; |
| 318 | }; |
| 319 | }; |
| 320 | |
| 321 | mpu6515_pin: mpu6515 { |
| 322 | irq { |
| 323 | pins = "gpio73"; |
| 324 | function = "gpio"; |
| 325 | bias-disable; |
| 326 | input-enable; |
| 327 | }; |
| 328 | }; |
| 329 | |
| 330 | touch_pin: touch { |
| 331 | int { |
| 332 | pins = "gpio5"; |
| 333 | function = "gpio"; |
| 334 | |
| 335 | drive-strength = <2>; |
| 336 | bias-disable; |
| 337 | input-enable; |
| 338 | }; |
| 339 | |
| 340 | reset { |
| 341 | pins = "gpio8"; |
| 342 | function = "gpio"; |
| 343 | |
| 344 | drive-strength = <2>; |
| 345 | bias-pull-up; |
| 346 | }; |
| 347 | }; |
| 348 | |
| 349 | panel_pin: panel { |
| 350 | te { |
| 351 | pins = "gpio12"; |
| 352 | function = "mdp_vsync"; |
| 353 | |
| 354 | drive-strength = <2>; |
| 355 | bias-disable; |
| 356 | }; |
| 357 | }; |
| 358 | }; |
| 359 | |
| 360 | sdhci@f9824900 { |
| 361 | status = "ok"; |
| 362 | |
| 363 | vmmc-supply = <&pm8941_l20>; |
| 364 | vqmmc-supply = <&pm8941_s3>; |
| 365 | |
| 366 | bus-width = <8>; |
| 367 | non-removable; |
| 368 | |
| 369 | pinctrl-names = "default"; |
| 370 | pinctrl-0 = <&sdhc1_pin_a>; |
| 371 | }; |
| 372 | |
| 373 | sdhci@f98a4900 { |
| 374 | status = "ok"; |
| 375 | |
| 376 | max-frequency = <100000000>; |
| 377 | bus-width = <4>; |
| 378 | non-removable; |
| 379 | vmmc-supply = <&vreg_wlan>; |
| 380 | vqmmc-supply = <&pm8941_s3>; |
| 381 | |
| 382 | pinctrl-names = "default"; |
| 383 | pinctrl-0 = <&sdhc2_pin_a>; |
| 384 | |
| 385 | #address-cells = <1>; |
| 386 | #size-cells = <0>; |
| 387 | |
| 388 | bcrmf@1 { |
| 389 | compatible = "brcm,bcm4339-fmac", "brcm,bcm4329-fmac"; |
| 390 | reg = <1>; |
| 391 | |
| 392 | brcm,drive-strength = <10>; |
| 393 | |
| 394 | pinctrl-names = "default"; |
| 395 | pinctrl-0 = <&wlan_sleep_clk_pin>; |
| 396 | }; |
| 397 | }; |
| 398 | |
| 399 | gpio-keys { |
| 400 | compatible = "gpio-keys"; |
| 401 | input-name = "gpio-keys"; |
| 402 | |
| 403 | pinctrl-names = "default"; |
| 404 | pinctrl-0 = <&gpio_keys_pin_a>; |
| 405 | |
| 406 | volume-up { |
| 407 | label = "volume_up"; |
| 408 | gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>; |
| 409 | linux,input-type = <1>; |
| 410 | linux,code = <KEY_VOLUMEUP>; |
| 411 | }; |
| 412 | |
| 413 | volume-down { |
| 414 | label = "volume_down"; |
| 415 | gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>; |
| 416 | linux,input-type = <1>; |
| 417 | linux,code = <KEY_VOLUMEDOWN>; |
| 418 | }; |
| 419 | }; |
| 420 | |
| 421 | i2c@f9967000 { |
| 422 | status = "ok"; |
| 423 | pinctrl-names = "default"; |
| 424 | pinctrl-0 = <&i2c11_pins>; |
| 425 | clock-frequency = <355000>; |
| 426 | qcom,src-freq = <50000000>; |
| 427 | |
| 428 | led-controller@38 { |
| 429 | compatible = "ti,lm3630a"; |
| 430 | status = "ok"; |
| 431 | reg = <0x38>; |
| 432 | |
| 433 | #address-cells = <1>; |
| 434 | #size-cells = <0>; |
| 435 | |
| 436 | led@0 { |
| 437 | reg = <0>; |
| 438 | led-sources = <0 1>; |
| 439 | label = "lcd-backlight"; |
| 440 | default-brightness = <200>; |
| 441 | }; |
| 442 | }; |
| 443 | }; |
| 444 | |
| 445 | i2c@f9968000 { |
| 446 | status = "ok"; |
| 447 | pinctrl-names = "default"; |
| 448 | pinctrl-0 = <&i2c12_pins>; |
| 449 | clock-frequency = <100000>; |
| 450 | qcom,src-freq = <50000000>; |
| 451 | |
| 452 | mpu6515@68 { |
| 453 | compatible = "invensense,mpu6515"; |
| 454 | reg = <0x68>; |
| 455 | interrupts-extended = <&msmgpio 73 IRQ_TYPE_EDGE_FALLING>; |
| 456 | vddio-supply = <&pm8941_lvs1>; |
| 457 | |
| 458 | pinctrl-names = "default"; |
| 459 | pinctrl-0 = <&mpu6515_pin>; |
| 460 | |
| 461 | i2c-gate { |
| 462 | #address-cells = <1>; |
| 463 | #size-cells = <0>; |
| 464 | ak8963@f { |
| 465 | compatible = "asahi-kasei,ak8963"; |
| 466 | reg = <0x0f>; |
| 467 | gpios = <&msmgpio 67 0>; |
| 468 | vid-supply = <&pm8941_lvs1>; |
| 469 | vdd-supply = <&pm8941_l17>; |
| 470 | }; |
| 471 | |
| 472 | bmp280@76 { |
| 473 | compatible = "bosch,bmp280"; |
| 474 | reg = <0x76>; |
| 475 | vdda-supply = <&pm8941_lvs1>; |
| 476 | vddd-supply = <&pm8941_l17>; |
| 477 | }; |
| 478 | }; |
| 479 | }; |
| 480 | }; |
| 481 | |
| 482 | i2c@f9923000 { |
| 483 | status = "ok"; |
| 484 | pinctrl-names = "default"; |
| 485 | pinctrl-0 = <&i2c1_pins>; |
| 486 | clock-frequency = <100000>; |
| 487 | qcom,src-freq = <50000000>; |
| 488 | |
| 489 | charger: bq24192@6b { |
| 490 | compatible = "ti,bq24192"; |
| 491 | reg = <0x6b>; |
| 492 | interrupts-extended = <&spmi_bus 0 0xd5 0 IRQ_TYPE_EDGE_FALLING>; |
| 493 | |
| 494 | omit-battery-class; |
| 495 | |
| 496 | usb_otg_vbus: usb-otg-vbus { }; |
| 497 | }; |
| 498 | }; |
| 499 | |
| 500 | i2c@f9924000 { |
| 501 | status = "ok"; |
| 502 | |
| 503 | clock-frequency = <355000>; |
| 504 | qcom,src-freq = <50000000>; |
| 505 | |
| 506 | pinctrl-names = "default"; |
| 507 | pinctrl-0 = <&i2c2_pins>; |
| 508 | |
| 509 | synaptics@70 { |
| 510 | compatible = "syna,rmi4-i2c"; |
| 511 | reg = <0x70>; |
| 512 | |
| 513 | interrupts-extended = <&msmgpio 5 IRQ_TYPE_EDGE_FALLING>; |
| 514 | vdd-supply = <&pm8941_l22>; |
| 515 | vio-supply = <&pm8941_lvs3>; |
| 516 | |
| 517 | pinctrl-names = "default"; |
| 518 | pinctrl-0 = <&touch_pin>; |
| 519 | |
| 520 | #address-cells = <1>; |
| 521 | #size-cells = <0>; |
| 522 | |
| 523 | rmi4-f01@1 { |
| 524 | reg = <0x1>; |
| 525 | syna,nosleep-mode = <1>; |
| 526 | }; |
| 527 | |
| 528 | rmi4-f12@12 { |
| 529 | reg = <0x12>; |
| 530 | syna,sensor-type = <1>; |
| 531 | }; |
| 532 | }; |
| 533 | }; |
| 534 | |
| 535 | i2c@f9925000 { |
| 536 | status = "ok"; |
| 537 | pinctrl-names = "default"; |
| 538 | pinctrl-0 = <&i2c3_pins>; |
| 539 | clock-frequency = <100000>; |
| 540 | qcom,src-freq = <50000000>; |
| 541 | |
| 542 | avago_apds993@39 { |
| 543 | compatible = "avago,apds9930"; |
| 544 | reg = <0x39>; |
| 545 | interrupts-extended = <&msmgpio 61 IRQ_TYPE_EDGE_FALLING>; |
| 546 | vdd-supply = <&pm8941_l17>; |
| 547 | vddio-supply = <&pm8941_lvs1>; |
| 548 | led-max-microamp = <100000>; |
| 549 | amstaos,proximity-diodes = <0>; |
| 550 | }; |
| 551 | }; |
| 552 | |
| 553 | usb@f9a55000 { |
| 554 | status = "ok"; |
| 555 | |
| 556 | phys = <&usb_hs1_phy>; |
| 557 | phy-select = <&tcsr 0xb000 0>; |
| 558 | |
| 559 | extcon = <&charger>, <&usb_id>; |
| 560 | vbus-supply = <&usb_otg_vbus>; |
| 561 | |
| 562 | hnp-disable; |
| 563 | srp-disable; |
| 564 | adp-disable; |
| 565 | |
| 566 | ulpi { |
| 567 | phy@a { |
| 568 | status = "ok"; |
| 569 | |
| 570 | v1p8-supply = <&pm8941_l6>; |
| 571 | v3p3-supply = <&pm8941_l24>; |
| 572 | |
| 573 | qcom,init-seq = /bits/ 8 <0x1 0x64>; |
| 574 | }; |
| 575 | }; |
| 576 | }; |
| 577 | |
| 578 | mdss@fd900000 { |
| 579 | status = "ok"; |
| 580 | |
| 581 | mdp@fd900000 { |
| 582 | status = "ok"; |
| 583 | }; |
| 584 | |
| 585 | dsi@fd922800 { |
| 586 | status = "ok"; |
| 587 | |
| 588 | vdda-supply = <&pm8941_l2>; |
| 589 | vdd-supply = <&pm8941_lvs3>; |
| 590 | vddio-supply = <&pm8941_l12>; |
| 591 | |
| 592 | #address-cells = <1>; |
| 593 | #size-cells = <0>; |
| 594 | |
| 595 | ports { |
| 596 | port@1 { |
| 597 | endpoint { |
| 598 | remote-endpoint = <&panel_in>; |
| 599 | data-lanes = <0 1 2 3>; |
| 600 | }; |
| 601 | }; |
| 602 | }; |
| 603 | |
| 604 | panel: panel@0 { |
| 605 | reg = <0>; |
| 606 | compatible = "lg,acx467akm-7"; |
| 607 | |
| 608 | pinctrl-names = "default"; |
| 609 | pinctrl-0 = <&panel_pin>; |
| 610 | |
| 611 | port { |
| 612 | panel_in: endpoint { |
| 613 | remote-endpoint = <&dsi0_out>; |
| 614 | }; |
| 615 | }; |
| 616 | }; |
| 617 | }; |
| 618 | |
| 619 | dsi-phy@fd922a00 { |
| 620 | status = "ok"; |
| 621 | |
| 622 | vddio-supply = <&pm8941_l12>; |
| 623 | }; |
| 624 | }; |
| 625 | }; |
| 626 | |
| 627 | &spmi_bus { |
| 628 | pm8941@0 { |
| 629 | gpios@c000 { |
| 630 | gpio_keys_pin_a: gpio-keys-active { |
| 631 | pins = "gpio2", "gpio3"; |
| 632 | function = "normal"; |
| 633 | |
| 634 | bias-pull-up; |
| 635 | power-source = <PM8941_GPIO_S3>; |
| 636 | }; |
| 637 | |
| 638 | wlan_sleep_clk_pin: wl-sleep-clk { |
| 639 | pins = "gpio16"; |
| 640 | function = "func2"; |
| 641 | |
| 642 | output-high; |
| 643 | power-source = <PM8941_GPIO_S3>; |
| 644 | }; |
| 645 | |
| 646 | wlan_regulator_pin: wl-reg-active { |
| 647 | pins = "gpio17"; |
| 648 | function = "normal"; |
| 649 | |
| 650 | bias-disable; |
| 651 | power-source = <PM8941_GPIO_S3>; |
| 652 | }; |
| 653 | |
| 654 | otg { |
| 655 | gpio-hog; |
| 656 | gpios = <35 GPIO_ACTIVE_HIGH>; |
| 657 | output-high; |
| 658 | line-name = "otg-gpio"; |
| 659 | }; |
| 660 | }; |
| 661 | }; |
| 662 | }; |