| b.liu | e958203 | 2025-04-17 19:18:16 +0800 | [diff] [blame^] | 1 | --- a/drivers/mtd/nand/raw/Kconfig |
| 2 | +++ b/drivers/mtd/nand/raw/Kconfig |
| 3 | @@ -559,4 +559,8 @@ config MTD_NAND_RB4XX |
| 4 | Enables support for the NAND flash chip on Mikrotik Routerboard |
| 5 | RB4xx series. |
| 6 | |
| 7 | +config MTD_NAND_RB91X |
| 8 | + tristate "MikroTik RB91x NAND driver support" |
| 9 | + depends on ATH79 && MTD_RAW_NAND |
| 10 | + |
| 11 | endif # MTD_RAW_NAND |
| 12 | --- a/drivers/mtd/nand/raw/Makefile |
| 13 | +++ b/drivers/mtd/nand/raw/Makefile |
| 14 | @@ -59,6 +59,7 @@ obj-$(CONFIG_MTD_NAND_STM32_FMC2) += stm |
| 15 | obj-$(CONFIG_MTD_NAND_MESON) += meson_nand.o |
| 16 | obj-$(CONFIG_MTD_NAND_AR934X) += ar934x_nand.o |
| 17 | obj-$(CONFIG_MTD_NAND_RB4XX) += nand_rb4xx.o |
| 18 | +obj-$(CONFIG_MTD_NAND_RB91X) += rb91x_nand.o |
| 19 | |
| 20 | nand-objs := nand_base.o nand_legacy.o nand_bbt.o nand_timings.o nand_ids.o |
| 21 | nand-objs += nand_onfi.o |
| 22 | --- a/drivers/gpio/Kconfig |
| 23 | +++ b/drivers/gpio/Kconfig |
| 24 | @@ -130,6 +130,10 @@ config GPIO_ATH79 |
| 25 | Select this option to enable GPIO driver for |
| 26 | Atheros AR71XX/AR724X/AR913X SoC devices. |
| 27 | |
| 28 | +config GPIO_LATCH |
| 29 | + tristate "MikroTik RouterBOARD GPIO latch support" |
| 30 | + depends on ATH79 |
| 31 | + |
| 32 | config GPIO_RASPBERRYPI_EXP |
| 33 | tristate "Raspberry Pi 3 GPIO Expander" |
| 34 | default RASPBERRYPI_FIRMWARE |
| 35 | --- a/drivers/gpio/Makefile |
| 36 | +++ b/drivers/gpio/Makefile |
| 37 | @@ -67,6 +67,7 @@ obj-$(CONFIG_GPIO_IT87) += gpio-it87.o |
| 38 | obj-$(CONFIG_GPIO_IXP4XX) += gpio-ixp4xx.o |
| 39 | obj-$(CONFIG_GPIO_JANZ_TTL) += gpio-janz-ttl.o |
| 40 | obj-$(CONFIG_GPIO_KEMPLD) += gpio-kempld.o |
| 41 | +obj-$(CONFIG_GPIO_LATCH) += gpio-latch.o |
| 42 | obj-$(CONFIG_GPIO_LOONGSON1) += gpio-loongson1.o |
| 43 | obj-$(CONFIG_GPIO_LOONGSON) += gpio-loongson.o |
| 44 | obj-$(CONFIG_GPIO_LP3943) += gpio-lp3943.o |