| /* | 
 |  * linux/drivers/char/ds1620.c: Dallas Semiconductors DS1620 | 
 |  *   thermometer driver (as used in the Rebel.com NetWinder) | 
 |  */ | 
 | #include <linux/module.h> | 
 | #include <linux/miscdevice.h> | 
 | #include <linux/delay.h> | 
 | #include <linux/proc_fs.h> | 
 | #include <linux/seq_file.h> | 
 | #include <linux/capability.h> | 
 | #include <linux/init.h> | 
 | #include <linux/mutex.h> | 
 |  | 
 | #include <mach/hardware.h> | 
 | #include <asm/mach-types.h> | 
 | #include <linux/uaccess.h> | 
 | #include <asm/therm.h> | 
 |  | 
 | #ifdef CONFIG_PROC_FS | 
 | /* define for /proc interface */ | 
 | #define THERM_USE_PROC | 
 | #endif | 
 |  | 
 | /* Definitions for DS1620 chip */ | 
 | #define THERM_START_CONVERT	0xee | 
 | #define THERM_RESET		0xaf | 
 | #define THERM_READ_CONFIG	0xac | 
 | #define THERM_READ_TEMP		0xaa | 
 | #define THERM_READ_TL		0xa2 | 
 | #define THERM_READ_TH		0xa1 | 
 | #define THERM_WRITE_CONFIG	0x0c | 
 | #define THERM_WRITE_TL		0x02 | 
 | #define THERM_WRITE_TH		0x01 | 
 |  | 
 | #define CFG_CPU			2 | 
 | #define CFG_1SHOT		1 | 
 |  | 
 | static DEFINE_MUTEX(ds1620_mutex); | 
 | static const char *fan_state[] = { "off", "on", "on (hardwired)" }; | 
 |  | 
 | /* | 
 |  * Start of NetWinder specifics | 
 |  *  Note!  We have to hold the gpio lock with IRQs disabled over the | 
 |  *  whole of our transaction to the Dallas chip, since there is a | 
 |  *  chance that the WaveArtist driver could touch these bits to | 
 |  *  enable or disable the speaker. | 
 |  */ | 
 | extern unsigned int system_rev; | 
 |  | 
 | static inline void netwinder_ds1620_set_clk(int clk) | 
 | { | 
 | 	nw_gpio_modify_op(GPIO_DSCLK, clk ? GPIO_DSCLK : 0); | 
 | } | 
 |  | 
 | static inline void netwinder_ds1620_set_data(int dat) | 
 | { | 
 | 	nw_gpio_modify_op(GPIO_DATA, dat ? GPIO_DATA : 0); | 
 | } | 
 |  | 
 | static inline int netwinder_ds1620_get_data(void) | 
 | { | 
 | 	return nw_gpio_read() & GPIO_DATA; | 
 | } | 
 |  | 
 | static inline void netwinder_ds1620_set_data_dir(int dir) | 
 | { | 
 | 	nw_gpio_modify_io(GPIO_DATA, dir ? GPIO_DATA : 0); | 
 | } | 
 |  | 
 | static inline void netwinder_ds1620_reset(void) | 
 | { | 
 | 	nw_cpld_modify(CPLD_DS_ENABLE, 0); | 
 | 	nw_cpld_modify(CPLD_DS_ENABLE, CPLD_DS_ENABLE); | 
 | } | 
 |  | 
 | static inline void netwinder_lock(unsigned long *flags) | 
 | { | 
 | 	raw_spin_lock_irqsave(&nw_gpio_lock, *flags); | 
 | } | 
 |  | 
 | static inline void netwinder_unlock(unsigned long *flags) | 
 | { | 
 | 	raw_spin_unlock_irqrestore(&nw_gpio_lock, *flags); | 
 | } | 
 |  | 
 | static inline void netwinder_set_fan(int i) | 
 | { | 
 | 	unsigned long flags; | 
 |  | 
 | 	raw_spin_lock_irqsave(&nw_gpio_lock, flags); | 
 | 	nw_gpio_modify_op(GPIO_FAN, i ? GPIO_FAN : 0); | 
 | 	raw_spin_unlock_irqrestore(&nw_gpio_lock, flags); | 
 | } | 
 |  | 
 | static inline int netwinder_get_fan(void) | 
 | { | 
 | 	if ((system_rev & 0xf000) == 0x4000) | 
 | 		return FAN_ALWAYS_ON; | 
 |  | 
 | 	return (nw_gpio_read() & GPIO_FAN) ? FAN_ON : FAN_OFF; | 
 | } | 
 |  | 
 | /* | 
 |  * End of NetWinder specifics | 
 |  */ | 
 |  | 
 | static void ds1620_send_bits(int nr, int value) | 
 | { | 
 | 	int i; | 
 |  | 
 | 	for (i = 0; i < nr; i++) { | 
 | 		netwinder_ds1620_set_data(value & 1); | 
 | 		netwinder_ds1620_set_clk(0); | 
 | 		udelay(1); | 
 | 		netwinder_ds1620_set_clk(1); | 
 | 		udelay(1); | 
 |  | 
 | 		value >>= 1; | 
 | 	} | 
 | } | 
 |  | 
 | static unsigned int ds1620_recv_bits(int nr) | 
 | { | 
 | 	unsigned int value = 0, mask = 1; | 
 | 	int i; | 
 |  | 
 | 	netwinder_ds1620_set_data(0); | 
 |  | 
 | 	for (i = 0; i < nr; i++) { | 
 | 		netwinder_ds1620_set_clk(0); | 
 | 		udelay(1); | 
 |  | 
 | 		if (netwinder_ds1620_get_data()) | 
 | 			value |= mask; | 
 |  | 
 | 		mask <<= 1; | 
 |  | 
 | 		netwinder_ds1620_set_clk(1); | 
 | 		udelay(1); | 
 | 	} | 
 |  | 
 | 	return value; | 
 | } | 
 |  | 
 | static void ds1620_out(int cmd, int bits, int value) | 
 | { | 
 | 	unsigned long flags; | 
 |  | 
 | 	netwinder_lock(&flags); | 
 | 	netwinder_ds1620_set_clk(1); | 
 | 	netwinder_ds1620_set_data_dir(0); | 
 | 	netwinder_ds1620_reset(); | 
 |  | 
 | 	udelay(1); | 
 |  | 
 | 	ds1620_send_bits(8, cmd); | 
 | 	if (bits) | 
 | 		ds1620_send_bits(bits, value); | 
 |  | 
 | 	udelay(1); | 
 |  | 
 | 	netwinder_ds1620_reset(); | 
 | 	netwinder_unlock(&flags); | 
 |  | 
 | 	msleep(20); | 
 | } | 
 |  | 
 | static unsigned int ds1620_in(int cmd, int bits) | 
 | { | 
 | 	unsigned long flags; | 
 | 	unsigned int value; | 
 |  | 
 | 	netwinder_lock(&flags); | 
 | 	netwinder_ds1620_set_clk(1); | 
 | 	netwinder_ds1620_set_data_dir(0); | 
 | 	netwinder_ds1620_reset(); | 
 |  | 
 | 	udelay(1); | 
 |  | 
 | 	ds1620_send_bits(8, cmd); | 
 |  | 
 | 	netwinder_ds1620_set_data_dir(1); | 
 | 	value = ds1620_recv_bits(bits); | 
 |  | 
 | 	netwinder_ds1620_reset(); | 
 | 	netwinder_unlock(&flags); | 
 |  | 
 | 	return value; | 
 | } | 
 |  | 
 | static int cvt_9_to_int(unsigned int val) | 
 | { | 
 | 	if (val & 0x100) | 
 | 		val |= 0xfffffe00; | 
 |  | 
 | 	return val; | 
 | } | 
 |  | 
 | static void ds1620_write_state(struct therm *therm) | 
 | { | 
 | 	ds1620_out(THERM_WRITE_CONFIG, 8, CFG_CPU); | 
 | 	ds1620_out(THERM_WRITE_TL, 9, therm->lo); | 
 | 	ds1620_out(THERM_WRITE_TH, 9, therm->hi); | 
 | 	ds1620_out(THERM_START_CONVERT, 0, 0); | 
 | } | 
 |  | 
 | static void ds1620_read_state(struct therm *therm) | 
 | { | 
 | 	therm->lo = cvt_9_to_int(ds1620_in(THERM_READ_TL, 9)); | 
 | 	therm->hi = cvt_9_to_int(ds1620_in(THERM_READ_TH, 9)); | 
 | } | 
 |  | 
 | static int ds1620_open(struct inode *inode, struct file *file) | 
 | { | 
 | 	return nonseekable_open(inode, file); | 
 | } | 
 |  | 
 | static ssize_t | 
 | ds1620_read(struct file *file, char __user *buf, size_t count, loff_t *ptr) | 
 | { | 
 | 	signed int cur_temp; | 
 | 	signed char cur_temp_degF; | 
 |  | 
 | 	cur_temp = cvt_9_to_int(ds1620_in(THERM_READ_TEMP, 9)) >> 1; | 
 |  | 
 | 	/* convert to Fahrenheit, as per wdt.c */ | 
 | 	cur_temp_degF = (cur_temp * 9) / 5 + 32; | 
 |  | 
 | 	if (copy_to_user(buf, &cur_temp_degF, 1)) | 
 | 		return -EFAULT; | 
 |  | 
 | 	return 1; | 
 | } | 
 |  | 
 | static int | 
 | ds1620_ioctl(struct file *file, unsigned int cmd, unsigned long arg) | 
 | { | 
 | 	struct therm therm; | 
 | 	union { | 
 | 		struct therm __user *therm; | 
 | 		int __user *i; | 
 | 	} uarg; | 
 | 	int i; | 
 |  | 
 | 	uarg.i = (int __user *)arg; | 
 |  | 
 | 	switch(cmd) { | 
 | 	case CMD_SET_THERMOSTATE: | 
 | 	case CMD_SET_THERMOSTATE2: | 
 | 		if (!capable(CAP_SYS_ADMIN)) | 
 | 			return -EPERM; | 
 |  | 
 | 		if (cmd == CMD_SET_THERMOSTATE) { | 
 | 			if (get_user(therm.hi, uarg.i)) | 
 | 				return -EFAULT; | 
 | 			therm.lo = therm.hi - 3; | 
 | 		} else { | 
 | 			if (copy_from_user(&therm, uarg.therm, sizeof(therm))) | 
 | 				return -EFAULT; | 
 | 		} | 
 |  | 
 | 		therm.lo <<= 1; | 
 | 		therm.hi <<= 1; | 
 |  | 
 | 		ds1620_write_state(&therm); | 
 | 		break; | 
 |  | 
 | 	case CMD_GET_THERMOSTATE: | 
 | 	case CMD_GET_THERMOSTATE2: | 
 | 		ds1620_read_state(&therm); | 
 |  | 
 | 		therm.lo >>= 1; | 
 | 		therm.hi >>= 1; | 
 |  | 
 | 		if (cmd == CMD_GET_THERMOSTATE) { | 
 | 			if (put_user(therm.hi, uarg.i)) | 
 | 				return -EFAULT; | 
 | 		} else { | 
 | 			if (copy_to_user(uarg.therm, &therm, sizeof(therm))) | 
 | 				return -EFAULT; | 
 | 		} | 
 | 		break; | 
 |  | 
 | 	case CMD_GET_TEMPERATURE: | 
 | 	case CMD_GET_TEMPERATURE2: | 
 | 		i = cvt_9_to_int(ds1620_in(THERM_READ_TEMP, 9)); | 
 |  | 
 | 		if (cmd == CMD_GET_TEMPERATURE) | 
 | 			i >>= 1; | 
 |  | 
 | 		return put_user(i, uarg.i) ? -EFAULT : 0; | 
 |  | 
 | 	case CMD_GET_STATUS: | 
 | 		i = ds1620_in(THERM_READ_CONFIG, 8) & 0xe3; | 
 |  | 
 | 		return put_user(i, uarg.i) ? -EFAULT : 0; | 
 |  | 
 | 	case CMD_GET_FAN: | 
 | 		i = netwinder_get_fan(); | 
 |  | 
 | 		return put_user(i, uarg.i) ? -EFAULT : 0; | 
 |  | 
 | 	case CMD_SET_FAN: | 
 | 		if (!capable(CAP_SYS_ADMIN)) | 
 | 			return -EPERM; | 
 |  | 
 | 		if (get_user(i, uarg.i)) | 
 | 			return -EFAULT; | 
 |  | 
 | 		netwinder_set_fan(i); | 
 | 		break; | 
 | 		 | 
 | 	default: | 
 | 		return -ENOIOCTLCMD; | 
 | 	} | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | static long | 
 | ds1620_unlocked_ioctl(struct file *file, unsigned int cmd, unsigned long arg) | 
 | { | 
 | 	int ret; | 
 |  | 
 | 	mutex_lock(&ds1620_mutex); | 
 | 	ret = ds1620_ioctl(file, cmd, arg); | 
 | 	mutex_unlock(&ds1620_mutex); | 
 |  | 
 | 	return ret; | 
 | } | 
 |  | 
 | #ifdef THERM_USE_PROC | 
 | static int ds1620_proc_therm_show(struct seq_file *m, void *v) | 
 | { | 
 | 	struct therm th; | 
 | 	int temp; | 
 |  | 
 | 	ds1620_read_state(&th); | 
 | 	temp =  cvt_9_to_int(ds1620_in(THERM_READ_TEMP, 9)); | 
 |  | 
 | 	seq_printf(m, "Thermostat: HI %i.%i, LOW %i.%i; temperature: %i.%i C, fan %s\n", | 
 | 		   th.hi >> 1, th.hi & 1 ? 5 : 0, | 
 | 		   th.lo >> 1, th.lo & 1 ? 5 : 0, | 
 | 		   temp  >> 1, temp  & 1 ? 5 : 0, | 
 | 		   fan_state[netwinder_get_fan()]); | 
 | 	return 0; | 
 | } | 
 | #endif | 
 |  | 
 | static const struct file_operations ds1620_fops = { | 
 | 	.owner		= THIS_MODULE, | 
 | 	.open		= ds1620_open, | 
 | 	.read		= ds1620_read, | 
 | 	.unlocked_ioctl	= ds1620_unlocked_ioctl, | 
 | 	.llseek		= no_llseek, | 
 | }; | 
 |  | 
 | static struct miscdevice ds1620_miscdev = { | 
 | 	TEMP_MINOR, | 
 | 	"temp", | 
 | 	&ds1620_fops | 
 | }; | 
 |  | 
 | static int __init ds1620_init(void) | 
 | { | 
 | 	int ret; | 
 | 	struct therm th, th_start; | 
 |  | 
 | 	if (!machine_is_netwinder()) | 
 | 		return -ENODEV; | 
 |  | 
 | 	ds1620_out(THERM_RESET, 0, 0); | 
 | 	ds1620_out(THERM_WRITE_CONFIG, 8, CFG_CPU); | 
 | 	ds1620_out(THERM_START_CONVERT, 0, 0); | 
 |  | 
 | 	/* | 
 | 	 * Trigger the fan to start by setting | 
 | 	 * temperature high point low.  This kicks | 
 | 	 * the fan into action. | 
 | 	 */ | 
 | 	ds1620_read_state(&th); | 
 | 	th_start.lo = 0; | 
 | 	th_start.hi = 1; | 
 | 	ds1620_write_state(&th_start); | 
 |  | 
 | 	msleep(2000); | 
 |  | 
 | 	ds1620_write_state(&th); | 
 |  | 
 | 	ret = misc_register(&ds1620_miscdev); | 
 | 	if (ret < 0) | 
 | 		return ret; | 
 |  | 
 | #ifdef THERM_USE_PROC | 
 | 	if (!proc_create_single("therm", 0, NULL, ds1620_proc_therm_show)) | 
 | 		printk(KERN_ERR "therm: unable to register /proc/therm\n"); | 
 | #endif | 
 |  | 
 | 	ds1620_read_state(&th); | 
 | 	ret = cvt_9_to_int(ds1620_in(THERM_READ_TEMP, 9)); | 
 |  | 
 | 	printk(KERN_INFO "Thermostat: high %i.%i, low %i.%i, " | 
 | 	       "current %i.%i C, fan %s.\n", | 
 | 	       th.hi >> 1, th.hi & 1 ? 5 : 0, | 
 | 	       th.lo >> 1, th.lo & 1 ? 5 : 0, | 
 | 	       ret   >> 1, ret   & 1 ? 5 : 0, | 
 | 	       fan_state[netwinder_get_fan()]); | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | static void __exit ds1620_exit(void) | 
 | { | 
 | #ifdef THERM_USE_PROC | 
 | 	remove_proc_entry("therm", NULL); | 
 | #endif | 
 | 	misc_deregister(&ds1620_miscdev); | 
 | } | 
 |  | 
 | module_init(ds1620_init); | 
 | module_exit(ds1620_exit); | 
 |  | 
 | MODULE_LICENSE("GPL"); |