| // SPDX-License-Identifier: GPL-2.0 | 
 | /* | 
 |  * MediaTek xHCI Host Controller Driver | 
 |  * | 
 |  * Copyright (c) 2015 MediaTek Inc. | 
 |  * Author: | 
 |  *  Chunfeng Yun <chunfeng.yun@mediatek.com> | 
 |  */ | 
 |  | 
 | #include <linux/clk.h> | 
 | #include <linux/dma-mapping.h> | 
 | #include <linux/iopoll.h> | 
 | #include <linux/kernel.h> | 
 | #include <linux/mfd/syscon.h> | 
 | #include <linux/module.h> | 
 | #include <linux/of.h> | 
 | #include <linux/platform_device.h> | 
 | #include <linux/pm_runtime.h> | 
 | #include <linux/regmap.h> | 
 | #include <linux/regulator/consumer.h> | 
 |  | 
 | #include "xhci.h" | 
 | #include "xhci-mtk.h" | 
 |  | 
 | /* ip_pw_ctrl0 register */ | 
 | #define CTRL0_IP_SW_RST	BIT(0) | 
 |  | 
 | /* ip_pw_ctrl1 register */ | 
 | #define CTRL1_IP_HOST_PDN	BIT(0) | 
 |  | 
 | /* ip_pw_ctrl2 register */ | 
 | #define CTRL2_IP_DEV_PDN	BIT(0) | 
 |  | 
 | /* ip_pw_sts1 register */ | 
 | #define STS1_IP_SLEEP_STS	BIT(30) | 
 | #define STS1_U3_MAC_RST	BIT(16) | 
 | #define STS1_XHCI_RST		BIT(11) | 
 | #define STS1_SYS125_RST	BIT(10) | 
 | #define STS1_REF_RST		BIT(8) | 
 | #define STS1_SYSPLL_STABLE	BIT(0) | 
 |  | 
 | /* ip_xhci_cap register */ | 
 | #define CAP_U3_PORT_NUM(p)	((p) & 0xff) | 
 | #define CAP_U2_PORT_NUM(p)	(((p) >> 8) & 0xff) | 
 |  | 
 | /* u3_ctrl_p register */ | 
 | #define CTRL_U3_PORT_HOST_SEL	BIT(2) | 
 | #define CTRL_U3_PORT_PDN	BIT(1) | 
 | #define CTRL_U3_PORT_DIS	BIT(0) | 
 |  | 
 | /* u2_ctrl_p register */ | 
 | #define CTRL_U2_PORT_HOST_SEL	BIT(2) | 
 | #define CTRL_U2_PORT_PDN	BIT(1) | 
 | #define CTRL_U2_PORT_DIS	BIT(0) | 
 |  | 
 | /* u2_phy_pll register */ | 
 | #define CTRL_U2_FORCE_PLL_STB	BIT(28) | 
 |  | 
 | /* usb remote wakeup registers in syscon */ | 
 | /* mt8173 etc */ | 
 | #define PERI_WK_CTRL1	0x4 | 
 | #define WC1_IS_C(x)	(((x) & 0xf) << 26)  /* cycle debounce */ | 
 | #define WC1_IS_EN	BIT(25) | 
 | #define WC1_IS_P	BIT(6)  /* polarity for ip sleep */ | 
 |  | 
 | /* mt2712 etc */ | 
 | #define PERI_SSUSB_SPM_CTRL	0x0 | 
 | #define SSC_IP_SLEEP_EN	BIT(4) | 
 | #define SSC_SPM_INT_EN		BIT(1) | 
 |  | 
 | enum ssusb_uwk_vers { | 
 | 	SSUSB_UWK_V1 = 1, | 
 | 	SSUSB_UWK_V2, | 
 | }; | 
 |  | 
 | static int xhci_mtk_host_enable(struct xhci_hcd_mtk *mtk) | 
 | { | 
 | 	struct mu3c_ippc_regs __iomem *ippc = mtk->ippc_regs; | 
 | 	u32 value, check_val; | 
 | 	int u3_ports_disabed = 0; | 
 | 	int ret; | 
 | 	int i; | 
 |  | 
 | 	if (!mtk->has_ippc) | 
 | 		return 0; | 
 |  | 
 | 	/* power on host ip */ | 
 | 	value = readl(&ippc->ip_pw_ctr1); | 
 | 	value &= ~CTRL1_IP_HOST_PDN; | 
 | 	writel(value, &ippc->ip_pw_ctr1); | 
 |  | 
 | 	/* power on and enable u3 ports except skipped ones */ | 
 | 	for (i = 0; i < mtk->num_u3_ports; i++) { | 
 | 		if ((0x1 << i) & mtk->u3p_dis_msk) { | 
 | 			u3_ports_disabed++; | 
 | 			continue; | 
 | 		} | 
 |  | 
 | 		value = readl(&ippc->u3_ctrl_p[i]); | 
 | 		value &= ~(CTRL_U3_PORT_PDN | CTRL_U3_PORT_DIS); | 
 | 		value |= CTRL_U3_PORT_HOST_SEL; | 
 | 		writel(value, &ippc->u3_ctrl_p[i]); | 
 | 	} | 
 |  | 
 | 	/* power on and enable all u2 ports */ | 
 | 	for (i = 0; i < mtk->num_u2_ports; i++) { | 
 | 		value = readl(&ippc->u2_ctrl_p[i]); | 
 | 		value &= ~(CTRL_U2_PORT_PDN | CTRL_U2_PORT_DIS); | 
 | 		value |= CTRL_U2_PORT_HOST_SEL; | 
 | 		writel(value, &ippc->u2_ctrl_p[i]); | 
 | 	} | 
 |  | 
 | 	/* | 
 | 	 * wait for clocks to be stable, and clock domains reset to | 
 | 	 * be inactive after power on and enable ports | 
 | 	 */ | 
 | 	check_val = STS1_SYSPLL_STABLE | STS1_REF_RST | | 
 | 			STS1_SYS125_RST | STS1_XHCI_RST; | 
 |  | 
 | 	if (mtk->num_u3_ports > u3_ports_disabed) | 
 | 		check_val |= STS1_U3_MAC_RST; | 
 |  | 
 | 	ret = readl_poll_timeout(&ippc->ip_pw_sts1, value, | 
 | 			  (check_val == (value & check_val)), 100, 20000); | 
 | 	if (ret) { | 
 | 		dev_err(mtk->dev, "clocks are not stable (0x%x)\n", value); | 
 | 		return ret; | 
 | 	} | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | static int xhci_mtk_host_disable(struct xhci_hcd_mtk *mtk) | 
 | { | 
 | 	struct mu3c_ippc_regs __iomem *ippc = mtk->ippc_regs; | 
 | 	u32 value; | 
 | 	int ret; | 
 | 	int i; | 
 |  | 
 | 	if (!mtk->has_ippc) | 
 | 		return 0; | 
 |  | 
 | 	/* power down u3 ports except skipped ones */ | 
 | 	for (i = 0; i < mtk->num_u3_ports; i++) { | 
 | 		if ((0x1 << i) & mtk->u3p_dis_msk) | 
 | 			continue; | 
 |  | 
 | 		value = readl(&ippc->u3_ctrl_p[i]); | 
 | 		value |= CTRL_U3_PORT_PDN; | 
 | 		writel(value, &ippc->u3_ctrl_p[i]); | 
 | 	} | 
 |  | 
 | 	/* power down all u2 ports */ | 
 | 	for (i = 0; i < mtk->num_u2_ports; i++) { | 
 | 		value = readl(&ippc->u2_ctrl_p[i]); | 
 | 		value |= CTRL_U2_PORT_PDN; | 
 | 		writel(value, &ippc->u2_ctrl_p[i]); | 
 | 	} | 
 |  | 
 | 	/* power down host ip */ | 
 | 	value = readl(&ippc->ip_pw_ctr1); | 
 | 	value |= CTRL1_IP_HOST_PDN; | 
 | 	writel(value, &ippc->ip_pw_ctr1); | 
 |  | 
 | 	/* wait for host ip to sleep */ | 
 | 	ret = readl_poll_timeout(&ippc->ip_pw_sts1, value, | 
 | 			  (value & STS1_IP_SLEEP_STS), 100, 100000); | 
 | 	if (ret) { | 
 | 		dev_err(mtk->dev, "ip sleep failed!!!\n"); | 
 | 		return ret; | 
 | 	} | 
 | 	return 0; | 
 | } | 
 |  | 
 | static int xhci_mtk_ssusb_config(struct xhci_hcd_mtk *mtk) | 
 | { | 
 | 	struct mu3c_ippc_regs __iomem *ippc = mtk->ippc_regs; | 
 | 	u32 value; | 
 |  | 
 | 	if (!mtk->has_ippc) | 
 | 		return 0; | 
 |  | 
 | 	/* reset whole ip */ | 
 | 	value = readl(&ippc->ip_pw_ctr0); | 
 | 	value |= CTRL0_IP_SW_RST; | 
 | 	writel(value, &ippc->ip_pw_ctr0); | 
 | 	udelay(1); | 
 | 	value = readl(&ippc->ip_pw_ctr0); | 
 | 	value &= ~CTRL0_IP_SW_RST; | 
 | 	writel(value, &ippc->ip_pw_ctr0); | 
 |  | 
 | 	/* | 
 | 	 * device ip is default power-on in fact | 
 | 	 * power down device ip, otherwise ip-sleep will fail | 
 | 	 */ | 
 | 	value = readl(&ippc->ip_pw_ctr2); | 
 | 	value |= CTRL2_IP_DEV_PDN; | 
 | 	writel(value, &ippc->ip_pw_ctr2); | 
 |  | 
 | 	value = readl(&ippc->ip_xhci_cap); | 
 | 	mtk->num_u3_ports = CAP_U3_PORT_NUM(value); | 
 | 	mtk->num_u2_ports = CAP_U2_PORT_NUM(value); | 
 | 	dev_dbg(mtk->dev, "%s u2p:%d, u3p:%d\n", __func__, | 
 | 			mtk->num_u2_ports, mtk->num_u3_ports); | 
 |  | 
 | 	return xhci_mtk_host_enable(mtk); | 
 | } | 
 |  | 
 | static int xhci_mtk_clks_get(struct xhci_hcd_mtk *mtk) | 
 | { | 
 | 	struct device *dev = mtk->dev; | 
 |  | 
 | 	mtk->sys_clk = devm_clk_get(dev, "sys_ck"); | 
 | 	if (IS_ERR(mtk->sys_clk)) { | 
 | 		dev_err(dev, "fail to get sys_ck\n"); | 
 | 		return PTR_ERR(mtk->sys_clk); | 
 | 	} | 
 |  | 
 | 	mtk->ref_clk = devm_clk_get_optional(dev, "ref_ck"); | 
 | 	if (IS_ERR(mtk->ref_clk)) | 
 | 		return PTR_ERR(mtk->ref_clk); | 
 |  | 
 | 	mtk->mcu_clk = devm_clk_get_optional(dev, "mcu_ck"); | 
 | 	if (IS_ERR(mtk->mcu_clk)) | 
 | 		return PTR_ERR(mtk->mcu_clk); | 
 |  | 
 | 	mtk->dma_clk = devm_clk_get_optional(dev, "dma_ck"); | 
 | 	return PTR_ERR_OR_ZERO(mtk->dma_clk); | 
 | } | 
 |  | 
 | static int xhci_mtk_clks_enable(struct xhci_hcd_mtk *mtk) | 
 | { | 
 | 	int ret; | 
 |  | 
 | 	ret = clk_prepare_enable(mtk->ref_clk); | 
 | 	if (ret) { | 
 | 		dev_err(mtk->dev, "failed to enable ref_clk\n"); | 
 | 		goto ref_clk_err; | 
 | 	} | 
 |  | 
 | 	ret = clk_prepare_enable(mtk->sys_clk); | 
 | 	if (ret) { | 
 | 		dev_err(mtk->dev, "failed to enable sys_clk\n"); | 
 | 		goto sys_clk_err; | 
 | 	} | 
 |  | 
 | 	ret = clk_prepare_enable(mtk->mcu_clk); | 
 | 	if (ret) { | 
 | 		dev_err(mtk->dev, "failed to enable mcu_clk\n"); | 
 | 		goto mcu_clk_err; | 
 | 	} | 
 |  | 
 | 	ret = clk_prepare_enable(mtk->dma_clk); | 
 | 	if (ret) { | 
 | 		dev_err(mtk->dev, "failed to enable dma_clk\n"); | 
 | 		goto dma_clk_err; | 
 | 	} | 
 |  | 
 | 	return 0; | 
 |  | 
 | dma_clk_err: | 
 | 	clk_disable_unprepare(mtk->mcu_clk); | 
 | mcu_clk_err: | 
 | 	clk_disable_unprepare(mtk->sys_clk); | 
 | sys_clk_err: | 
 | 	clk_disable_unprepare(mtk->ref_clk); | 
 | ref_clk_err: | 
 | 	return ret; | 
 | } | 
 |  | 
 | static void xhci_mtk_clks_disable(struct xhci_hcd_mtk *mtk) | 
 | { | 
 | 	clk_disable_unprepare(mtk->dma_clk); | 
 | 	clk_disable_unprepare(mtk->mcu_clk); | 
 | 	clk_disable_unprepare(mtk->sys_clk); | 
 | 	clk_disable_unprepare(mtk->ref_clk); | 
 | } | 
 |  | 
 | /* only clocks can be turn off for ip-sleep wakeup mode */ | 
 | static void usb_wakeup_ip_sleep_set(struct xhci_hcd_mtk *mtk, bool enable) | 
 | { | 
 | 	u32 reg, msk, val; | 
 |  | 
 | 	switch (mtk->uwk_vers) { | 
 | 	case SSUSB_UWK_V1: | 
 | 		reg = mtk->uwk_reg_base + PERI_WK_CTRL1; | 
 | 		msk = WC1_IS_EN | WC1_IS_C(0xf) | WC1_IS_P; | 
 | 		val = enable ? (WC1_IS_EN | WC1_IS_C(0x8)) : 0; | 
 | 		break; | 
 | 	case SSUSB_UWK_V2: | 
 | 		reg = mtk->uwk_reg_base + PERI_SSUSB_SPM_CTRL; | 
 | 		msk = SSC_IP_SLEEP_EN | SSC_SPM_INT_EN; | 
 | 		val = enable ? msk : 0; | 
 | 		break; | 
 | 	default: | 
 | 		return; | 
 | 	} | 
 | 	regmap_update_bits(mtk->uwk, reg, msk, val); | 
 | } | 
 |  | 
 | static int usb_wakeup_of_property_parse(struct xhci_hcd_mtk *mtk, | 
 | 				struct device_node *dn) | 
 | { | 
 | 	struct of_phandle_args args; | 
 | 	int ret; | 
 |  | 
 | 	/* Wakeup function is optional */ | 
 | 	mtk->uwk_en = of_property_read_bool(dn, "wakeup-source"); | 
 | 	if (!mtk->uwk_en) | 
 | 		return 0; | 
 |  | 
 | 	ret = of_parse_phandle_with_fixed_args(dn, | 
 | 				"mediatek,syscon-wakeup", 2, 0, &args); | 
 | 	if (ret) | 
 | 		return ret; | 
 |  | 
 | 	mtk->uwk_reg_base = args.args[0]; | 
 | 	mtk->uwk_vers = args.args[1]; | 
 | 	mtk->uwk = syscon_node_to_regmap(args.np); | 
 | 	of_node_put(args.np); | 
 | 	dev_info(mtk->dev, "uwk - reg:0x%x, version:%d\n", | 
 | 			mtk->uwk_reg_base, mtk->uwk_vers); | 
 |  | 
 | 	return PTR_ERR_OR_ZERO(mtk->uwk); | 
 |  | 
 | } | 
 |  | 
 | static void usb_wakeup_set(struct xhci_hcd_mtk *mtk, bool enable) | 
 | { | 
 | 	if (mtk->uwk_en) | 
 | 		usb_wakeup_ip_sleep_set(mtk, enable); | 
 | } | 
 |  | 
 | static int xhci_mtk_setup(struct usb_hcd *hcd); | 
 | static const struct xhci_driver_overrides xhci_mtk_overrides __initconst = { | 
 | 	.reset = xhci_mtk_setup, | 
 | }; | 
 |  | 
 | static struct hc_driver __read_mostly xhci_mtk_hc_driver; | 
 |  | 
 | static int xhci_mtk_ldos_enable(struct xhci_hcd_mtk *mtk) | 
 | { | 
 | 	int ret; | 
 |  | 
 | 	ret = regulator_enable(mtk->vbus); | 
 | 	if (ret) { | 
 | 		dev_err(mtk->dev, "failed to enable vbus\n"); | 
 | 		return ret; | 
 | 	} | 
 |  | 
 | 	ret = regulator_enable(mtk->vusb33); | 
 | 	if (ret) { | 
 | 		dev_err(mtk->dev, "failed to enable vusb33\n"); | 
 | 		regulator_disable(mtk->vbus); | 
 | 		return ret; | 
 | 	} | 
 | 	return 0; | 
 | } | 
 |  | 
 | static void xhci_mtk_ldos_disable(struct xhci_hcd_mtk *mtk) | 
 | { | 
 | 	regulator_disable(mtk->vbus); | 
 | 	regulator_disable(mtk->vusb33); | 
 | } | 
 |  | 
 | static void xhci_mtk_quirks(struct device *dev, struct xhci_hcd *xhci) | 
 | { | 
 | 	struct usb_hcd *hcd = xhci_to_hcd(xhci); | 
 | 	struct xhci_hcd_mtk *mtk = hcd_to_mtk(hcd); | 
 |  | 
 | 	/* | 
 | 	 * As of now platform drivers don't provide MSI support so we ensure | 
 | 	 * here that the generic code does not try to make a pci_dev from our | 
 | 	 * dev struct in order to setup MSI | 
 | 	 */ | 
 | 	xhci->quirks |= XHCI_PLAT; | 
 | 	xhci->quirks |= XHCI_MTK_HOST; | 
 | 	/* | 
 | 	 * MTK host controller gives a spurious successful event after a | 
 | 	 * short transfer. Ignore it. | 
 | 	 */ | 
 | 	xhci->quirks |= XHCI_SPURIOUS_SUCCESS; | 
 | 	if (mtk->lpm_support) | 
 | 		xhci->quirks |= XHCI_LPM_SUPPORT; | 
 | } | 
 |  | 
 | /* called during probe() after chip reset completes */ | 
 | static int xhci_mtk_setup(struct usb_hcd *hcd) | 
 | { | 
 | 	struct xhci_hcd_mtk *mtk = hcd_to_mtk(hcd); | 
 | 	int ret; | 
 |  | 
 | 	if (usb_hcd_is_primary_hcd(hcd)) { | 
 | 		ret = xhci_mtk_ssusb_config(mtk); | 
 | 		if (ret) | 
 | 			return ret; | 
 | 	} | 
 |  | 
 | 	ret = xhci_gen_setup(hcd, xhci_mtk_quirks); | 
 | 	if (ret) | 
 | 		return ret; | 
 |  | 
 | 	if (usb_hcd_is_primary_hcd(hcd)) { | 
 | 		ret = xhci_mtk_sch_init(mtk); | 
 | 		if (ret) | 
 | 			return ret; | 
 | 	} | 
 |  | 
 | 	return ret; | 
 | } | 
 |  | 
 | static int xhci_mtk_probe(struct platform_device *pdev) | 
 | { | 
 | 	struct device *dev = &pdev->dev; | 
 | 	struct device_node *node = dev->of_node; | 
 | 	struct xhci_hcd_mtk *mtk; | 
 | 	const struct hc_driver *driver; | 
 | 	struct xhci_hcd *xhci; | 
 | 	struct resource *res; | 
 | 	struct usb_hcd *hcd; | 
 | 	int ret = -ENODEV; | 
 | 	int irq; | 
 |  | 
 | 	if (usb_disabled()) | 
 | 		return -ENODEV; | 
 |  | 
 | 	driver = &xhci_mtk_hc_driver; | 
 | 	mtk = devm_kzalloc(dev, sizeof(*mtk), GFP_KERNEL); | 
 | 	if (!mtk) | 
 | 		return -ENOMEM; | 
 |  | 
 | 	mtk->dev = dev; | 
 | 	mtk->vbus = devm_regulator_get(dev, "vbus"); | 
 | 	if (IS_ERR(mtk->vbus)) { | 
 | 		dev_err(dev, "fail to get vbus\n"); | 
 | 		return PTR_ERR(mtk->vbus); | 
 | 	} | 
 |  | 
 | 	mtk->vusb33 = devm_regulator_get(dev, "vusb33"); | 
 | 	if (IS_ERR(mtk->vusb33)) { | 
 | 		dev_err(dev, "fail to get vusb33\n"); | 
 | 		return PTR_ERR(mtk->vusb33); | 
 | 	} | 
 |  | 
 | 	ret = xhci_mtk_clks_get(mtk); | 
 | 	if (ret) | 
 | 		return ret; | 
 |  | 
 | 	mtk->lpm_support = of_property_read_bool(node, "usb3-lpm-capable"); | 
 | 	/* optional property, ignore the error if it does not exist */ | 
 | 	of_property_read_u32(node, "mediatek,u3p-dis-msk", | 
 | 			     &mtk->u3p_dis_msk); | 
 |  | 
 | 	ret = usb_wakeup_of_property_parse(mtk, node); | 
 | 	if (ret) { | 
 | 		dev_err(dev, "failed to parse uwk property\n"); | 
 | 		return ret; | 
 | 	} | 
 |  | 
 | 	pm_runtime_enable(dev); | 
 | 	pm_runtime_get_sync(dev); | 
 | 	device_enable_async_suspend(dev); | 
 |  | 
 | 	ret = xhci_mtk_ldos_enable(mtk); | 
 | 	if (ret) | 
 | 		goto disable_pm; | 
 |  | 
 | 	ret = xhci_mtk_clks_enable(mtk); | 
 | 	if (ret) | 
 | 		goto disable_ldos; | 
 |  | 
 | 	irq = platform_get_irq(pdev, 0); | 
 | 	if (irq < 0) { | 
 | 		ret = irq; | 
 | 		goto disable_clk; | 
 | 	} | 
 |  | 
 | 	/* Initialize dma_mask and coherent_dma_mask to 32-bits */ | 
 | 	ret = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(32)); | 
 | 	if (ret) | 
 | 		goto disable_clk; | 
 |  | 
 | 	hcd = usb_create_hcd(driver, dev, dev_name(dev)); | 
 | 	if (!hcd) { | 
 | 		ret = -ENOMEM; | 
 | 		goto disable_clk; | 
 | 	} | 
 |  | 
 | 	/* | 
 | 	 * USB 2.0 roothub is stored in the platform_device. | 
 | 	 * Swap it with mtk HCD. | 
 | 	 */ | 
 | 	mtk->hcd = platform_get_drvdata(pdev); | 
 | 	platform_set_drvdata(pdev, mtk); | 
 |  | 
 | 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "mac"); | 
 | 	hcd->regs = devm_ioremap_resource(dev, res); | 
 | 	if (IS_ERR(hcd->regs)) { | 
 | 		ret = PTR_ERR(hcd->regs); | 
 | 		goto put_usb2_hcd; | 
 | 	} | 
 | 	hcd->rsrc_start = res->start; | 
 | 	hcd->rsrc_len = resource_size(res); | 
 |  | 
 | 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "ippc"); | 
 | 	if (res) {	/* ippc register is optional */ | 
 | 		mtk->ippc_regs = devm_ioremap_resource(dev, res); | 
 | 		if (IS_ERR(mtk->ippc_regs)) { | 
 | 			ret = PTR_ERR(mtk->ippc_regs); | 
 | 			goto put_usb2_hcd; | 
 | 		} | 
 | 		mtk->has_ippc = true; | 
 | 	} else { | 
 | 		mtk->has_ippc = false; | 
 | 	} | 
 |  | 
 | 	device_init_wakeup(dev, true); | 
 |  | 
 | 	xhci = hcd_to_xhci(hcd); | 
 | 	xhci->main_hcd = hcd; | 
 |  | 
 | 	/* | 
 | 	 * imod_interval is the interrupt moderation value in nanoseconds. | 
 | 	 * The increment interval is 8 times as much as that defined in | 
 | 	 * the xHCI spec on MTK's controller. | 
 | 	 */ | 
 | 	xhci->imod_interval = 5000; | 
 | 	device_property_read_u32(dev, "imod-interval-ns", &xhci->imod_interval); | 
 |  | 
 | 	xhci->shared_hcd = usb_create_shared_hcd(driver, dev, | 
 | 			dev_name(dev), hcd); | 
 | 	if (!xhci->shared_hcd) { | 
 | 		ret = -ENOMEM; | 
 | 		goto disable_device_wakeup; | 
 | 	} | 
 |  | 
 | 	ret = usb_add_hcd(hcd, irq, IRQF_SHARED); | 
 | 	if (ret) | 
 | 		goto put_usb3_hcd; | 
 |  | 
 | 	if (HCC_MAX_PSA(xhci->hcc_params) >= 4) | 
 | 		xhci->shared_hcd->can_do_streams = 1; | 
 |  | 
 | 	ret = usb_add_hcd(xhci->shared_hcd, irq, IRQF_SHARED); | 
 | 	if (ret) | 
 | 		goto dealloc_usb2_hcd; | 
 |  | 
 | 	return 0; | 
 |  | 
 | dealloc_usb2_hcd: | 
 | 	usb_remove_hcd(hcd); | 
 |  | 
 | put_usb3_hcd: | 
 | 	xhci_mtk_sch_exit(mtk); | 
 | 	usb_put_hcd(xhci->shared_hcd); | 
 |  | 
 | disable_device_wakeup: | 
 | 	device_init_wakeup(dev, false); | 
 |  | 
 | put_usb2_hcd: | 
 | 	usb_put_hcd(hcd); | 
 |  | 
 | disable_clk: | 
 | 	xhci_mtk_clks_disable(mtk); | 
 |  | 
 | disable_ldos: | 
 | 	xhci_mtk_ldos_disable(mtk); | 
 |  | 
 | disable_pm: | 
 | 	pm_runtime_put_sync(dev); | 
 | 	pm_runtime_disable(dev); | 
 | 	return ret; | 
 | } | 
 |  | 
 | static int xhci_mtk_remove(struct platform_device *dev) | 
 | { | 
 | 	struct xhci_hcd_mtk *mtk = platform_get_drvdata(dev); | 
 | 	struct usb_hcd	*hcd = mtk->hcd; | 
 | 	struct xhci_hcd	*xhci = hcd_to_xhci(hcd); | 
 | 	struct usb_hcd  *shared_hcd = xhci->shared_hcd; | 
 |  | 
 | 	pm_runtime_put_noidle(&dev->dev); | 
 | 	pm_runtime_disable(&dev->dev); | 
 |  | 
 | 	xhci->xhc_state |= XHCI_STATE_REMOVING; | 
 |  | 
 | 	usb_remove_hcd(shared_hcd); | 
 | 	xhci->shared_hcd = NULL; | 
 | 	device_init_wakeup(&dev->dev, false); | 
 |  | 
 | 	usb_remove_hcd(hcd); | 
 | 	usb_put_hcd(shared_hcd); | 
 | 	usb_put_hcd(hcd); | 
 | 	xhci_mtk_sch_exit(mtk); | 
 | 	xhci_mtk_clks_disable(mtk); | 
 | 	xhci_mtk_ldos_disable(mtk); | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | /* | 
 |  * if ip sleep fails, and all clocks are disabled, access register will hang | 
 |  * AHB bus, so stop polling roothubs to avoid regs access on bus suspend. | 
 |  * and no need to check whether ip sleep failed or not; this will cause SPM | 
 |  * to wake up system immediately after system suspend complete if ip sleep | 
 |  * fails, it is what we wanted. | 
 |  */ | 
 | static int __maybe_unused xhci_mtk_suspend(struct device *dev) | 
 | { | 
 | 	struct xhci_hcd_mtk *mtk = dev_get_drvdata(dev); | 
 | 	struct usb_hcd *hcd = mtk->hcd; | 
 | 	struct xhci_hcd *xhci = hcd_to_xhci(hcd); | 
 |  | 
 | 	xhci_dbg(xhci, "%s: stop port polling\n", __func__); | 
 | 	clear_bit(HCD_FLAG_POLL_RH, &hcd->flags); | 
 | 	del_timer_sync(&hcd->rh_timer); | 
 | 	clear_bit(HCD_FLAG_POLL_RH, &xhci->shared_hcd->flags); | 
 | 	del_timer_sync(&xhci->shared_hcd->rh_timer); | 
 |  | 
 | 	xhci_mtk_host_disable(mtk); | 
 | 	xhci_mtk_clks_disable(mtk); | 
 | 	usb_wakeup_set(mtk, true); | 
 | 	return 0; | 
 | } | 
 |  | 
 | static int __maybe_unused xhci_mtk_resume(struct device *dev) | 
 | { | 
 | 	struct xhci_hcd_mtk *mtk = dev_get_drvdata(dev); | 
 | 	struct usb_hcd *hcd = mtk->hcd; | 
 | 	struct xhci_hcd *xhci = hcd_to_xhci(hcd); | 
 |  | 
 | 	usb_wakeup_set(mtk, false); | 
 | 	xhci_mtk_clks_enable(mtk); | 
 | 	xhci_mtk_host_enable(mtk); | 
 |  | 
 | 	xhci_dbg(xhci, "%s: restart port polling\n", __func__); | 
 | 	set_bit(HCD_FLAG_POLL_RH, &xhci->shared_hcd->flags); | 
 | 	usb_hcd_poll_rh_status(xhci->shared_hcd); | 
 | 	set_bit(HCD_FLAG_POLL_RH, &hcd->flags); | 
 | 	usb_hcd_poll_rh_status(hcd); | 
 | 	return 0; | 
 | } | 
 |  | 
 | static const struct dev_pm_ops xhci_mtk_pm_ops = { | 
 | 	SET_SYSTEM_SLEEP_PM_OPS(xhci_mtk_suspend, xhci_mtk_resume) | 
 | }; | 
 | #define DEV_PM_OPS IS_ENABLED(CONFIG_PM) ? &xhci_mtk_pm_ops : NULL | 
 |  | 
 | #ifdef CONFIG_OF | 
 | static const struct of_device_id mtk_xhci_of_match[] = { | 
 | 	{ .compatible = "mediatek,mt8173-xhci"}, | 
 | 	{ .compatible = "mediatek,mtk-xhci"}, | 
 | 	{ }, | 
 | }; | 
 | MODULE_DEVICE_TABLE(of, mtk_xhci_of_match); | 
 | #endif | 
 |  | 
 | static struct platform_driver mtk_xhci_driver = { | 
 | 	.probe	= xhci_mtk_probe, | 
 | 	.remove	= xhci_mtk_remove, | 
 | 	.driver	= { | 
 | 		.name = "xhci-mtk", | 
 | 		.pm = DEV_PM_OPS, | 
 | 		.of_match_table = of_match_ptr(mtk_xhci_of_match), | 
 | 	}, | 
 | }; | 
 | MODULE_ALIAS("platform:xhci-mtk"); | 
 |  | 
 | static int __init xhci_mtk_init(void) | 
 | { | 
 | 	xhci_init_driver(&xhci_mtk_hc_driver, &xhci_mtk_overrides); | 
 | 	return platform_driver_register(&mtk_xhci_driver); | 
 | } | 
 | module_init(xhci_mtk_init); | 
 |  | 
 | static void __exit xhci_mtk_exit(void) | 
 | { | 
 | 	platform_driver_unregister(&mtk_xhci_driver); | 
 | } | 
 | module_exit(xhci_mtk_exit); | 
 |  | 
 | MODULE_AUTHOR("Chunfeng Yun <chunfeng.yun@mediatek.com>"); | 
 | MODULE_DESCRIPTION("MediaTek xHCI Host Controller Driver"); | 
 | MODULE_LICENSE("GPL v2"); |