| /*============================================================================= |
| # FileName: lynq_sim.h |
| # Desc: about SIMAPI |
| # Author: lei |
| # Version: V1.0 |
| # LastChange: 2022-03-31 |
| # History: |
| # If you need to use any API under lynq_sim, you must first call the lynq_sim_init() function to initialize these functions. |
| =============================================================================*/ |
| #ifndef __LYNQ_SIM__ |
| #define __LYNQ_SIM__ |
| #ifdef __cplusplus |
| extern "C" { |
| #endif |
| |
| int lynq_get_sim_status(int *card_status); |
| int lynq_get_imsi(char buf[]); |
| int lynq_sim_init(int utoken); |
| int lynq_sim_deinit(void); |
| int lynq_enable_pin(char pin[]); |
| int lynq_disable_pin(char pin[]); |
| int lynq_get_iccid(char buf[]); |
| int lynq_query_pin_lock(char *pin,int buf[]); |
| int lynq_verify_pin(char *pin); |
| int lynq_change_pin(char *old_pin, char *new_pin); |
| int lynq_unlock_pin(char *puk, char *pin); |
| int lynq_query_phone_number(char buf[]); |
| int lynq_switch_card(int slot); |
| int lynq_screen(int num); |
| int lynq_get_imei(char buf[]); |
| int lynq_get_imei_and_sv(char imei[],char sv[]); |
| |
| /** |
| * @brief Request SIM I/O operation. |
| * This is similar to the TS 27.007 "restricted SIM" operation |
| * where it assumes all of the EF selection will be done by the callee. |
| * @param list type: [IN] list[0]:one of the commands listed for TS 27.007 +CRSM.(command) |
| * type: [IN] list[1]:EF id(fileid) |
| * type: [IN] list[2]:offset(p1) |
| * type: [IN] list[3]:offset(p2) |
| * type: [IN] list[4]:response len,sometimes needn't care(p3) |
| * @param path type: [IN] "pathid" from TS 27.007 +CRSM command. |
| type: [IN] Path is in hex asciii format eg "7f205f70" |
| type: [IN] Path must always be provided. |
| * @param data type: [IN] May be NULL |
| * @param pin2 type: [IN] May be NULL |
| * @param aidPtr type: [IN] AID value, See ETSI 102.221 8.1 and 101.220 4, NULL if no value. |
| * @param sw type: [OUT] |
| * @param simResponse type: [OUT] response |
| * @return int |
| */ |
| int lynq_req_sim_io(int list[5], char *path, char *data, char *pin2, char *aidPtr, int sw[2], char *simResponse); |
| |
| /** |
| * @brief |
| * @param options type: [IN] [options] define whether you want to halt, power-off, or reboot the machine.May be NULL |
| * @param time type: [IN] [time] specifies when you want the shutdown to perform.May be NULL |
| * @param message type: [IN] [message] adds a message that announces the shutdown.May be NULL |
| * @return int |
| */ |
| int lynq_shutdown(char options[], char time[], char message[]); |
| |
| /** |
| * @brief get currnet version of mobiletek |
| * @param buf type: [out] My Param doc |
| * @return int |
| */ |
| int lynq_get_version(char buf[]); |
| |
| /** |
| * @brief sim power on/off |
| * |
| */ |
| int lynq_sim_power(int mode); |
| |
| /** |
| * @brief reset modem |
| * |
| */ |
| int lynq_reset_modem(void); |
| |
| /** |
| * @brief factory test to both radio on/off |
| * |
| */ |
| int lynq_factory_radio_state(int num); |
| |
| |
| #ifdef __cplusplus |
| } |
| #endif |
| |
| #endif |
| |