|  | /* | 
|  | * Rockchip usb PHY driver | 
|  | * | 
|  | * Copyright (C) 2014 Yunzhi Li <lyz@rock-chips.com> | 
|  | * Copyright (C) 2014 ROCKCHIP, Inc. | 
|  | * | 
|  | * This program is free software; you can redistribute it and/or modify | 
|  | * it under the terms of the GNU General Public License as published by | 
|  | * the Free Software Foundation; either version 2 of the License. | 
|  | * | 
|  | * This program is distributed in the hope that it will be useful, | 
|  | * but WITHOUT ANY WARRANTY; without even the implied warranty of | 
|  | * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the | 
|  | * GNU General Public License for more details. | 
|  | */ | 
|  |  | 
|  | #include <linux/clk.h> | 
|  | #include <linux/clk-provider.h> | 
|  | #include <linux/io.h> | 
|  | #include <linux/kernel.h> | 
|  | #include <linux/module.h> | 
|  | #include <linux/mutex.h> | 
|  | #include <linux/of.h> | 
|  | #include <linux/of_address.h> | 
|  | #include <linux/of_platform.h> | 
|  | #include <linux/phy/phy.h> | 
|  | #include <linux/platform_device.h> | 
|  | #include <linux/regulator/consumer.h> | 
|  | #include <linux/reset.h> | 
|  | #include <linux/regmap.h> | 
|  | #include <linux/mfd/syscon.h> | 
|  | #include <linux/delay.h> | 
|  |  | 
|  | static int enable_usb_uart; | 
|  |  | 
|  | #define HIWORD_UPDATE(val, mask) \ | 
|  | ((val) | (mask) << 16) | 
|  |  | 
|  | #define UOC_CON0_SIDDQ BIT(13) | 
|  |  | 
|  | struct rockchip_usb_phys { | 
|  | int reg; | 
|  | const char *pll_name; | 
|  | }; | 
|  |  | 
|  | struct rockchip_usb_phy_base; | 
|  | struct rockchip_usb_phy_pdata { | 
|  | struct rockchip_usb_phys *phys; | 
|  | int (*init_usb_uart)(struct regmap *grf); | 
|  | int usb_uart_phy; | 
|  | }; | 
|  |  | 
|  | struct rockchip_usb_phy_base { | 
|  | struct device *dev; | 
|  | struct regmap *reg_base; | 
|  | const struct rockchip_usb_phy_pdata *pdata; | 
|  | }; | 
|  |  | 
|  | struct rockchip_usb_phy { | 
|  | struct rockchip_usb_phy_base *base; | 
|  | struct device_node *np; | 
|  | unsigned int	reg_offset; | 
|  | struct clk	*clk; | 
|  | struct clk      *clk480m; | 
|  | struct clk_hw	clk480m_hw; | 
|  | struct phy	*phy; | 
|  | bool		uart_enabled; | 
|  | struct reset_control *reset; | 
|  | struct regulator *vbus; | 
|  | }; | 
|  |  | 
|  | static int rockchip_usb_phy_power(struct rockchip_usb_phy *phy, | 
|  | bool siddq) | 
|  | { | 
|  | u32 val = HIWORD_UPDATE(siddq ? UOC_CON0_SIDDQ : 0, UOC_CON0_SIDDQ); | 
|  |  | 
|  | return regmap_write(phy->base->reg_base, phy->reg_offset, val); | 
|  | } | 
|  |  | 
|  | static unsigned long rockchip_usb_phy480m_recalc_rate(struct clk_hw *hw, | 
|  | unsigned long parent_rate) | 
|  | { | 
|  | return 480000000; | 
|  | } | 
|  |  | 
|  | static void rockchip_usb_phy480m_disable(struct clk_hw *hw) | 
|  | { | 
|  | struct rockchip_usb_phy *phy = container_of(hw, | 
|  | struct rockchip_usb_phy, | 
|  | clk480m_hw); | 
|  |  | 
|  | if (phy->vbus) | 
|  | regulator_disable(phy->vbus); | 
|  |  | 
|  | /* Power down usb phy analog blocks by set siddq 1 */ | 
|  | rockchip_usb_phy_power(phy, 1); | 
|  | } | 
|  |  | 
|  | static int rockchip_usb_phy480m_enable(struct clk_hw *hw) | 
|  | { | 
|  | struct rockchip_usb_phy *phy = container_of(hw, | 
|  | struct rockchip_usb_phy, | 
|  | clk480m_hw); | 
|  |  | 
|  | /* Power up usb phy analog blocks by set siddq 0 */ | 
|  | return rockchip_usb_phy_power(phy, 0); | 
|  | } | 
|  |  | 
|  | static int rockchip_usb_phy480m_is_enabled(struct clk_hw *hw) | 
|  | { | 
|  | struct rockchip_usb_phy *phy = container_of(hw, | 
|  | struct rockchip_usb_phy, | 
|  | clk480m_hw); | 
|  | int ret; | 
|  | u32 val; | 
|  |  | 
|  | ret = regmap_read(phy->base->reg_base, phy->reg_offset, &val); | 
|  | if (ret < 0) | 
|  | return ret; | 
|  |  | 
|  | return (val & UOC_CON0_SIDDQ) ? 0 : 1; | 
|  | } | 
|  |  | 
|  | static const struct clk_ops rockchip_usb_phy480m_ops = { | 
|  | .enable = rockchip_usb_phy480m_enable, | 
|  | .disable = rockchip_usb_phy480m_disable, | 
|  | .is_enabled = rockchip_usb_phy480m_is_enabled, | 
|  | .recalc_rate = rockchip_usb_phy480m_recalc_rate, | 
|  | }; | 
|  |  | 
|  | static int rockchip_usb_phy_power_off(struct phy *_phy) | 
|  | { | 
|  | struct rockchip_usb_phy *phy = phy_get_drvdata(_phy); | 
|  |  | 
|  | if (phy->uart_enabled) | 
|  | return -EBUSY; | 
|  |  | 
|  | clk_disable_unprepare(phy->clk480m); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int rockchip_usb_phy_power_on(struct phy *_phy) | 
|  | { | 
|  | struct rockchip_usb_phy *phy = phy_get_drvdata(_phy); | 
|  |  | 
|  | if (phy->uart_enabled) | 
|  | return -EBUSY; | 
|  |  | 
|  | if (phy->vbus) { | 
|  | int ret; | 
|  |  | 
|  | ret = regulator_enable(phy->vbus); | 
|  | if (ret) | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | return clk_prepare_enable(phy->clk480m); | 
|  | } | 
|  |  | 
|  | static int rockchip_usb_phy_reset(struct phy *_phy) | 
|  | { | 
|  | struct rockchip_usb_phy *phy = phy_get_drvdata(_phy); | 
|  |  | 
|  | if (phy->reset) { | 
|  | reset_control_assert(phy->reset); | 
|  | udelay(10); | 
|  | reset_control_deassert(phy->reset); | 
|  | } | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static const struct phy_ops ops = { | 
|  | .power_on	= rockchip_usb_phy_power_on, | 
|  | .power_off	= rockchip_usb_phy_power_off, | 
|  | .reset		= rockchip_usb_phy_reset, | 
|  | .owner		= THIS_MODULE, | 
|  | }; | 
|  |  | 
|  | static void rockchip_usb_phy_action(void *data) | 
|  | { | 
|  | struct rockchip_usb_phy *rk_phy = data; | 
|  |  | 
|  | if (!rk_phy->uart_enabled) { | 
|  | of_clk_del_provider(rk_phy->np); | 
|  | clk_unregister(rk_phy->clk480m); | 
|  | } | 
|  |  | 
|  | if (rk_phy->clk) | 
|  | clk_put(rk_phy->clk); | 
|  | } | 
|  |  | 
|  | static int rockchip_usb_phy_init(struct rockchip_usb_phy_base *base, | 
|  | struct device_node *child) | 
|  | { | 
|  | struct rockchip_usb_phy *rk_phy; | 
|  | unsigned int reg_offset; | 
|  | const char *clk_name; | 
|  | struct clk_init_data init; | 
|  | int err, i; | 
|  |  | 
|  | rk_phy = devm_kzalloc(base->dev, sizeof(*rk_phy), GFP_KERNEL); | 
|  | if (!rk_phy) | 
|  | return -ENOMEM; | 
|  |  | 
|  | rk_phy->base = base; | 
|  | rk_phy->np = child; | 
|  |  | 
|  | if (of_property_read_u32(child, "reg", ®_offset)) { | 
|  | dev_err(base->dev, "missing reg property in node %s\n", | 
|  | child->name); | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | rk_phy->reset = of_reset_control_get(child, "phy-reset"); | 
|  | if (IS_ERR(rk_phy->reset)) | 
|  | rk_phy->reset = NULL; | 
|  |  | 
|  | rk_phy->reg_offset = reg_offset; | 
|  |  | 
|  | rk_phy->clk = of_clk_get_by_name(child, "phyclk"); | 
|  | if (IS_ERR(rk_phy->clk)) | 
|  | rk_phy->clk = NULL; | 
|  |  | 
|  | i = 0; | 
|  | init.name = NULL; | 
|  | while (base->pdata->phys[i].reg) { | 
|  | if (base->pdata->phys[i].reg == reg_offset) { | 
|  | init.name = base->pdata->phys[i].pll_name; | 
|  | break; | 
|  | } | 
|  | i++; | 
|  | } | 
|  |  | 
|  | if (!init.name) { | 
|  | dev_err(base->dev, "phy data not found\n"); | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | if (enable_usb_uart && base->pdata->usb_uart_phy == i) { | 
|  | dev_dbg(base->dev, "phy%d used as uart output\n", i); | 
|  | rk_phy->uart_enabled = true; | 
|  | } else { | 
|  | if (rk_phy->clk) { | 
|  | clk_name = __clk_get_name(rk_phy->clk); | 
|  | init.flags = 0; | 
|  | init.parent_names = &clk_name; | 
|  | init.num_parents = 1; | 
|  | } else { | 
|  | init.flags = 0; | 
|  | init.parent_names = NULL; | 
|  | init.num_parents = 0; | 
|  | } | 
|  |  | 
|  | init.ops = &rockchip_usb_phy480m_ops; | 
|  | rk_phy->clk480m_hw.init = &init; | 
|  |  | 
|  | rk_phy->clk480m = clk_register(base->dev, &rk_phy->clk480m_hw); | 
|  | if (IS_ERR(rk_phy->clk480m)) { | 
|  | err = PTR_ERR(rk_phy->clk480m); | 
|  | goto err_clk; | 
|  | } | 
|  |  | 
|  | err = of_clk_add_provider(child, of_clk_src_simple_get, | 
|  | rk_phy->clk480m); | 
|  | if (err < 0) | 
|  | goto err_clk_prov; | 
|  | } | 
|  |  | 
|  | err = devm_add_action_or_reset(base->dev, rockchip_usb_phy_action, | 
|  | rk_phy); | 
|  | if (err) | 
|  | return err; | 
|  |  | 
|  | rk_phy->phy = devm_phy_create(base->dev, child, &ops); | 
|  | if (IS_ERR(rk_phy->phy)) { | 
|  | dev_err(base->dev, "failed to create PHY\n"); | 
|  | return PTR_ERR(rk_phy->phy); | 
|  | } | 
|  | phy_set_drvdata(rk_phy->phy, rk_phy); | 
|  |  | 
|  | rk_phy->vbus = devm_regulator_get_optional(&rk_phy->phy->dev, "vbus"); | 
|  | if (IS_ERR(rk_phy->vbus)) { | 
|  | if (PTR_ERR(rk_phy->vbus) == -EPROBE_DEFER) | 
|  | return PTR_ERR(rk_phy->vbus); | 
|  | rk_phy->vbus = NULL; | 
|  | } | 
|  |  | 
|  | /* | 
|  | * When acting as uart-pipe, just keep clock on otherwise | 
|  | * only power up usb phy when it use, so disable it when init | 
|  | */ | 
|  | if (rk_phy->uart_enabled) | 
|  | return clk_prepare_enable(rk_phy->clk); | 
|  | else | 
|  | return rockchip_usb_phy_power(rk_phy, 1); | 
|  |  | 
|  | err_clk_prov: | 
|  | if (!rk_phy->uart_enabled) | 
|  | clk_unregister(rk_phy->clk480m); | 
|  | err_clk: | 
|  | if (rk_phy->clk) | 
|  | clk_put(rk_phy->clk); | 
|  | return err; | 
|  | } | 
|  |  | 
|  | static const struct rockchip_usb_phy_pdata rk3066a_pdata = { | 
|  | .phys = (struct rockchip_usb_phys[]){ | 
|  | { .reg = 0x17c, .pll_name = "sclk_otgphy0_480m" }, | 
|  | { .reg = 0x188, .pll_name = "sclk_otgphy1_480m" }, | 
|  | { /* sentinel */ } | 
|  | }, | 
|  | }; | 
|  |  | 
|  | static const struct rockchip_usb_phy_pdata rk3188_pdata = { | 
|  | .phys = (struct rockchip_usb_phys[]){ | 
|  | { .reg = 0x10c, .pll_name = "sclk_otgphy0_480m" }, | 
|  | { .reg = 0x11c, .pll_name = "sclk_otgphy1_480m" }, | 
|  | { /* sentinel */ } | 
|  | }, | 
|  | }; | 
|  |  | 
|  | #define RK3288_UOC0_CON0				0x320 | 
|  | #define RK3288_UOC0_CON0_COMMON_ON_N			BIT(0) | 
|  | #define RK3288_UOC0_CON0_DISABLE			BIT(4) | 
|  |  | 
|  | #define RK3288_UOC0_CON2				0x328 | 
|  | #define RK3288_UOC0_CON2_SOFT_CON_SEL			BIT(2) | 
|  |  | 
|  | #define RK3288_UOC0_CON3				0x32c | 
|  | #define RK3288_UOC0_CON3_UTMI_SUSPENDN			BIT(0) | 
|  | #define RK3288_UOC0_CON3_UTMI_OPMODE_NODRIVING		(1 << 1) | 
|  | #define RK3288_UOC0_CON3_UTMI_OPMODE_MASK		(3 << 1) | 
|  | #define RK3288_UOC0_CON3_UTMI_XCVRSEELCT_FSTRANSC	(1 << 3) | 
|  | #define RK3288_UOC0_CON3_UTMI_XCVRSEELCT_MASK		(3 << 3) | 
|  | #define RK3288_UOC0_CON3_UTMI_TERMSEL_FULLSPEED		BIT(5) | 
|  | #define RK3288_UOC0_CON3_BYPASSDMEN			BIT(6) | 
|  | #define RK3288_UOC0_CON3_BYPASSSEL			BIT(7) | 
|  |  | 
|  | /* | 
|  | * Enable the bypass of uart2 data through the otg usb phy. | 
|  | * Original description in the TRM. | 
|  | * 1. Disable the OTG block by setting OTGDISABLE0 to 1’b1. | 
|  | * 2. Disable the pull-up resistance on the D+ line by setting | 
|  | *    OPMODE0[1:0] to 2’b01. | 
|  | * 3. To ensure that the XO, Bias, and PLL blocks are powered down in Suspend | 
|  | *    mode, set COMMONONN to 1’b1. | 
|  | * 4. Place the USB PHY in Suspend mode by setting SUSPENDM0 to 1’b0. | 
|  | * 5. Set BYPASSSEL0 to 1’b1. | 
|  | * 6. To transmit data, controls BYPASSDMEN0, and BYPASSDMDATA0. | 
|  | * To receive data, monitor FSVPLUS0. | 
|  | * | 
|  | * The actual code in the vendor kernel does some things differently. | 
|  | */ | 
|  | static int __init rk3288_init_usb_uart(struct regmap *grf) | 
|  | { | 
|  | u32 val; | 
|  | int ret; | 
|  |  | 
|  | /* | 
|  | * COMMON_ON and DISABLE settings are described in the TRM, | 
|  | * but were not present in the original code. | 
|  | * Also disable the analog phy components to save power. | 
|  | */ | 
|  | val = HIWORD_UPDATE(RK3288_UOC0_CON0_COMMON_ON_N | 
|  | | RK3288_UOC0_CON0_DISABLE | 
|  | | UOC_CON0_SIDDQ, | 
|  | RK3288_UOC0_CON0_COMMON_ON_N | 
|  | | RK3288_UOC0_CON0_DISABLE | 
|  | | UOC_CON0_SIDDQ); | 
|  | ret = regmap_write(grf, RK3288_UOC0_CON0, val); | 
|  | if (ret) | 
|  | return ret; | 
|  |  | 
|  | val = HIWORD_UPDATE(RK3288_UOC0_CON2_SOFT_CON_SEL, | 
|  | RK3288_UOC0_CON2_SOFT_CON_SEL); | 
|  | ret = regmap_write(grf, RK3288_UOC0_CON2, val); | 
|  | if (ret) | 
|  | return ret; | 
|  |  | 
|  | val = HIWORD_UPDATE(RK3288_UOC0_CON3_UTMI_OPMODE_NODRIVING | 
|  | | RK3288_UOC0_CON3_UTMI_XCVRSEELCT_FSTRANSC | 
|  | | RK3288_UOC0_CON3_UTMI_TERMSEL_FULLSPEED, | 
|  | RK3288_UOC0_CON3_UTMI_SUSPENDN | 
|  | | RK3288_UOC0_CON3_UTMI_OPMODE_MASK | 
|  | | RK3288_UOC0_CON3_UTMI_XCVRSEELCT_MASK | 
|  | | RK3288_UOC0_CON3_UTMI_TERMSEL_FULLSPEED); | 
|  | ret = regmap_write(grf, RK3288_UOC0_CON3, val); | 
|  | if (ret) | 
|  | return ret; | 
|  |  | 
|  | val = HIWORD_UPDATE(RK3288_UOC0_CON3_BYPASSSEL | 
|  | | RK3288_UOC0_CON3_BYPASSDMEN, | 
|  | RK3288_UOC0_CON3_BYPASSSEL | 
|  | | RK3288_UOC0_CON3_BYPASSDMEN); | 
|  | ret = regmap_write(grf, RK3288_UOC0_CON3, val); | 
|  | if (ret) | 
|  | return ret; | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static const struct rockchip_usb_phy_pdata rk3288_pdata = { | 
|  | .phys = (struct rockchip_usb_phys[]){ | 
|  | { .reg = 0x320, .pll_name = "sclk_otgphy0_480m" }, | 
|  | { .reg = 0x334, .pll_name = "sclk_otgphy1_480m" }, | 
|  | { .reg = 0x348, .pll_name = "sclk_otgphy2_480m" }, | 
|  | { /* sentinel */ } | 
|  | }, | 
|  | .init_usb_uart = rk3288_init_usb_uart, | 
|  | .usb_uart_phy = 0, | 
|  | }; | 
|  |  | 
|  | static int rockchip_usb_phy_probe(struct platform_device *pdev) | 
|  | { | 
|  | struct device *dev = &pdev->dev; | 
|  | struct rockchip_usb_phy_base *phy_base; | 
|  | struct phy_provider *phy_provider; | 
|  | const struct of_device_id *match; | 
|  | struct device_node *child; | 
|  | int err; | 
|  |  | 
|  | phy_base = devm_kzalloc(dev, sizeof(*phy_base), GFP_KERNEL); | 
|  | if (!phy_base) | 
|  | return -ENOMEM; | 
|  |  | 
|  | match = of_match_device(dev->driver->of_match_table, dev); | 
|  | if (!match || !match->data) { | 
|  | dev_err(dev, "missing phy data\n"); | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | phy_base->pdata = match->data; | 
|  |  | 
|  | phy_base->dev = dev; | 
|  | phy_base->reg_base = ERR_PTR(-ENODEV); | 
|  | if (dev->parent && dev->parent->of_node) | 
|  | phy_base->reg_base = syscon_node_to_regmap( | 
|  | dev->parent->of_node); | 
|  | if (IS_ERR(phy_base->reg_base)) | 
|  | phy_base->reg_base = syscon_regmap_lookup_by_phandle( | 
|  | dev->of_node, "rockchip,grf"); | 
|  | if (IS_ERR(phy_base->reg_base)) { | 
|  | dev_err(&pdev->dev, "Missing rockchip,grf property\n"); | 
|  | return PTR_ERR(phy_base->reg_base); | 
|  | } | 
|  |  | 
|  | for_each_available_child_of_node(dev->of_node, child) { | 
|  | err = rockchip_usb_phy_init(phy_base, child); | 
|  | if (err) { | 
|  | of_node_put(child); | 
|  | return err; | 
|  | } | 
|  | } | 
|  |  | 
|  | phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate); | 
|  | return PTR_ERR_OR_ZERO(phy_provider); | 
|  | } | 
|  |  | 
|  | static const struct of_device_id rockchip_usb_phy_dt_ids[] = { | 
|  | { .compatible = "rockchip,rk3066a-usb-phy", .data = &rk3066a_pdata }, | 
|  | { .compatible = "rockchip,rk3188-usb-phy", .data = &rk3188_pdata }, | 
|  | { .compatible = "rockchip,rk3288-usb-phy", .data = &rk3288_pdata }, | 
|  | {} | 
|  | }; | 
|  |  | 
|  | MODULE_DEVICE_TABLE(of, rockchip_usb_phy_dt_ids); | 
|  |  | 
|  | static struct platform_driver rockchip_usb_driver = { | 
|  | .probe		= rockchip_usb_phy_probe, | 
|  | .driver		= { | 
|  | .name	= "rockchip-usb-phy", | 
|  | .of_match_table = rockchip_usb_phy_dt_ids, | 
|  | }, | 
|  | }; | 
|  |  | 
|  | module_platform_driver(rockchip_usb_driver); | 
|  |  | 
|  | #ifndef MODULE | 
|  | static int __init rockchip_init_usb_uart(void) | 
|  | { | 
|  | const struct of_device_id *match; | 
|  | const struct rockchip_usb_phy_pdata *data; | 
|  | struct device_node *np; | 
|  | struct regmap *grf; | 
|  | int ret; | 
|  |  | 
|  | if (!enable_usb_uart) | 
|  | return 0; | 
|  |  | 
|  | np = of_find_matching_node_and_match(NULL, rockchip_usb_phy_dt_ids, | 
|  | &match); | 
|  | if (!np) { | 
|  | pr_err("%s: failed to find usbphy node\n", __func__); | 
|  | return -ENOTSUPP; | 
|  | } | 
|  |  | 
|  | pr_debug("%s: using settings for %s\n", __func__, match->compatible); | 
|  | data = match->data; | 
|  |  | 
|  | if (!data->init_usb_uart) { | 
|  | pr_err("%s: usb-uart not available on %s\n", | 
|  | __func__, match->compatible); | 
|  | return -ENOTSUPP; | 
|  | } | 
|  |  | 
|  | grf = ERR_PTR(-ENODEV); | 
|  | if (np->parent) | 
|  | grf = syscon_node_to_regmap(np->parent); | 
|  | if (IS_ERR(grf)) | 
|  | grf = syscon_regmap_lookup_by_phandle(np, "rockchip,grf"); | 
|  | if (IS_ERR(grf)) { | 
|  | pr_err("%s: Missing rockchip,grf property, %lu\n", | 
|  | __func__, PTR_ERR(grf)); | 
|  | return PTR_ERR(grf); | 
|  | } | 
|  |  | 
|  | ret = data->init_usb_uart(grf); | 
|  | if (ret) { | 
|  | pr_err("%s: could not init usb_uart, %d\n", __func__, ret); | 
|  | enable_usb_uart = 0; | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | return 0; | 
|  | } | 
|  | early_initcall(rockchip_init_usb_uart); | 
|  |  | 
|  | static int __init rockchip_usb_uart(char *buf) | 
|  | { | 
|  | enable_usb_uart = true; | 
|  | return 0; | 
|  | } | 
|  | early_param("rockchip.usb_uart", rockchip_usb_uart); | 
|  | #endif | 
|  |  | 
|  | MODULE_AUTHOR("Yunzhi Li <lyz@rock-chips.com>"); | 
|  | MODULE_DESCRIPTION("Rockchip USB 2.0 PHY driver"); | 
|  | MODULE_LICENSE("GPL v2"); |