| /* | 
 |  * I2C Link Layer for ST NCI NFC controller familly based Driver | 
 |  * Copyright (C) 2014-2015 STMicroelectronics SAS. All rights reserved. | 
 |  * | 
 |  * This program is free software; you can redistribute it and/or modify it | 
 |  * under the terms and conditions of the GNU General Public License, | 
 |  * version 2, as published by the Free Software Foundation. | 
 |  * | 
 |  * This program is distributed in the hope that it will be useful, | 
 |  * but WITHOUT ANY WARRANTY; without even the implied warranty of | 
 |  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the | 
 |  * GNU General Public License for more details. | 
 |  * | 
 |  * You should have received a copy of the GNU General Public License | 
 |  * along with this program; if not, see <http://www.gnu.org/licenses/>. | 
 |  */ | 
 |  | 
 | #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt | 
 |  | 
 | #include <linux/module.h> | 
 | #include <linux/i2c.h> | 
 | #include <linux/gpio/consumer.h> | 
 | #include <linux/acpi.h> | 
 | #include <linux/interrupt.h> | 
 | #include <linux/delay.h> | 
 | #include <linux/nfc.h> | 
 | #include <linux/of.h> | 
 |  | 
 | #include "st-nci.h" | 
 |  | 
 | #define DRIVER_DESC "NCI NFC driver for ST_NCI" | 
 |  | 
 | /* ndlc header */ | 
 | #define ST_NCI_FRAME_HEADROOM 1 | 
 | #define ST_NCI_FRAME_TAILROOM 0 | 
 |  | 
 | #define ST_NCI_I2C_MIN_SIZE 4   /* PCB(1) + NCI Packet header(3) */ | 
 | #define ST_NCI_I2C_MAX_SIZE 250 /* req 4.2.1 */ | 
 |  | 
 | #define ST_NCI_DRIVER_NAME "st_nci" | 
 | #define ST_NCI_I2C_DRIVER_NAME "st_nci_i2c" | 
 |  | 
 | struct st_nci_i2c_phy { | 
 | 	struct i2c_client *i2c_dev; | 
 | 	struct llt_ndlc *ndlc; | 
 |  | 
 | 	bool irq_active; | 
 |  | 
 | 	struct gpio_desc *gpiod_reset; | 
 |  | 
 | 	struct st_nci_se_status se_status; | 
 | }; | 
 |  | 
 | static int st_nci_i2c_enable(void *phy_id) | 
 | { | 
 | 	struct st_nci_i2c_phy *phy = phy_id; | 
 |  | 
 | 	gpiod_set_value(phy->gpiod_reset, 0); | 
 | 	usleep_range(10000, 15000); | 
 | 	gpiod_set_value(phy->gpiod_reset, 1); | 
 | 	usleep_range(80000, 85000); | 
 |  | 
 | 	if (phy->ndlc->powered == 0 && phy->irq_active == 0) { | 
 | 		enable_irq(phy->i2c_dev->irq); | 
 | 		phy->irq_active = true; | 
 | 	} | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | static void st_nci_i2c_disable(void *phy_id) | 
 | { | 
 | 	struct st_nci_i2c_phy *phy = phy_id; | 
 |  | 
 | 	disable_irq_nosync(phy->i2c_dev->irq); | 
 | 	phy->irq_active = false; | 
 | } | 
 |  | 
 | /* | 
 |  * Writing a frame must not return the number of written bytes. | 
 |  * It must return either zero for success, or <0 for error. | 
 |  * In addition, it must not alter the skb | 
 |  */ | 
 | static int st_nci_i2c_write(void *phy_id, struct sk_buff *skb) | 
 | { | 
 | 	int r = -1; | 
 | 	struct st_nci_i2c_phy *phy = phy_id; | 
 | 	struct i2c_client *client = phy->i2c_dev; | 
 |  | 
 | 	if (phy->ndlc->hard_fault != 0) | 
 | 		return phy->ndlc->hard_fault; | 
 |  | 
 | 	r = i2c_master_send(client, skb->data, skb->len); | 
 | 	if (r < 0) {  /* Retry, chip was in standby */ | 
 | 		usleep_range(1000, 4000); | 
 | 		r = i2c_master_send(client, skb->data, skb->len); | 
 | 	} | 
 |  | 
 | 	if (r >= 0) { | 
 | 		if (r != skb->len) | 
 | 			r = -EREMOTEIO; | 
 | 		else | 
 | 			r = 0; | 
 | 	} | 
 |  | 
 | 	return r; | 
 | } | 
 |  | 
 | /* | 
 |  * Reads an ndlc frame and returns it in a newly allocated sk_buff. | 
 |  * returns: | 
 |  * 0 : if received frame is complete | 
 |  * -EREMOTEIO : i2c read error (fatal) | 
 |  * -EBADMSG : frame was incorrect and discarded | 
 |  * -ENOMEM : cannot allocate skb, frame dropped | 
 |  */ | 
 | static int st_nci_i2c_read(struct st_nci_i2c_phy *phy, | 
 | 				 struct sk_buff **skb) | 
 | { | 
 | 	int r; | 
 | 	u8 len; | 
 | 	u8 buf[ST_NCI_I2C_MAX_SIZE]; | 
 | 	struct i2c_client *client = phy->i2c_dev; | 
 |  | 
 | 	r = i2c_master_recv(client, buf, ST_NCI_I2C_MIN_SIZE); | 
 | 	if (r < 0) {  /* Retry, chip was in standby */ | 
 | 		usleep_range(1000, 4000); | 
 | 		r = i2c_master_recv(client, buf, ST_NCI_I2C_MIN_SIZE); | 
 | 	} | 
 |  | 
 | 	if (r != ST_NCI_I2C_MIN_SIZE) | 
 | 		return -EREMOTEIO; | 
 |  | 
 | 	len = be16_to_cpu(*(__be16 *) (buf + 2)); | 
 | 	if (len > ST_NCI_I2C_MAX_SIZE) { | 
 | 		nfc_err(&client->dev, "invalid frame len\n"); | 
 | 		return -EBADMSG; | 
 | 	} | 
 |  | 
 | 	*skb = alloc_skb(ST_NCI_I2C_MIN_SIZE + len, GFP_KERNEL); | 
 | 	if (*skb == NULL) | 
 | 		return -ENOMEM; | 
 |  | 
 | 	skb_reserve(*skb, ST_NCI_I2C_MIN_SIZE); | 
 | 	skb_put(*skb, ST_NCI_I2C_MIN_SIZE); | 
 | 	memcpy((*skb)->data, buf, ST_NCI_I2C_MIN_SIZE); | 
 |  | 
 | 	if (!len) | 
 | 		return 0; | 
 |  | 
 | 	r = i2c_master_recv(client, buf, len); | 
 | 	if (r != len) { | 
 | 		kfree_skb(*skb); | 
 | 		return -EREMOTEIO; | 
 | 	} | 
 |  | 
 | 	skb_put(*skb, len); | 
 | 	memcpy((*skb)->data + ST_NCI_I2C_MIN_SIZE, buf, len); | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | /* | 
 |  * Reads an ndlc frame from the chip. | 
 |  * | 
 |  * On ST_NCI, IRQ goes in idle state when read starts. | 
 |  */ | 
 | static irqreturn_t st_nci_irq_thread_fn(int irq, void *phy_id) | 
 | { | 
 | 	struct st_nci_i2c_phy *phy = phy_id; | 
 | 	struct i2c_client *client; | 
 | 	struct sk_buff *skb = NULL; | 
 | 	int r; | 
 |  | 
 | 	if (!phy || !phy->ndlc || irq != phy->i2c_dev->irq) { | 
 | 		WARN_ON_ONCE(1); | 
 | 		return IRQ_NONE; | 
 | 	} | 
 |  | 
 | 	client = phy->i2c_dev; | 
 | 	dev_dbg(&client->dev, "IRQ\n"); | 
 |  | 
 | 	if (phy->ndlc->hard_fault) | 
 | 		return IRQ_HANDLED; | 
 |  | 
 | 	if (!phy->ndlc->powered) { | 
 | 		st_nci_i2c_disable(phy); | 
 | 		return IRQ_HANDLED; | 
 | 	} | 
 |  | 
 | 	r = st_nci_i2c_read(phy, &skb); | 
 | 	if (r == -EREMOTEIO || r == -ENOMEM || r == -EBADMSG) | 
 | 		return IRQ_HANDLED; | 
 |  | 
 | 	ndlc_recv(phy->ndlc, skb); | 
 |  | 
 | 	return IRQ_HANDLED; | 
 | } | 
 |  | 
 | static struct nfc_phy_ops i2c_phy_ops = { | 
 | 	.write = st_nci_i2c_write, | 
 | 	.enable = st_nci_i2c_enable, | 
 | 	.disable = st_nci_i2c_disable, | 
 | }; | 
 |  | 
 | static const struct acpi_gpio_params reset_gpios = { 1, 0, false }; | 
 |  | 
 | static const struct acpi_gpio_mapping acpi_st_nci_gpios[] = { | 
 | 	{ "reset-gpios", &reset_gpios, 1 }, | 
 | 	{}, | 
 | }; | 
 |  | 
 | static int st_nci_i2c_probe(struct i2c_client *client, | 
 | 				  const struct i2c_device_id *id) | 
 | { | 
 | 	struct device *dev = &client->dev; | 
 | 	struct st_nci_i2c_phy *phy; | 
 | 	int r; | 
 |  | 
 | 	dev_dbg(&client->dev, "%s\n", __func__); | 
 | 	dev_dbg(&client->dev, "IRQ: %d\n", client->irq); | 
 |  | 
 | 	if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) { | 
 | 		nfc_err(&client->dev, "Need I2C_FUNC_I2C\n"); | 
 | 		return -ENODEV; | 
 | 	} | 
 |  | 
 | 	phy = devm_kzalloc(dev, sizeof(struct st_nci_i2c_phy), GFP_KERNEL); | 
 | 	if (!phy) | 
 | 		return -ENOMEM; | 
 |  | 
 | 	phy->i2c_dev = client; | 
 |  | 
 | 	i2c_set_clientdata(client, phy); | 
 |  | 
 | 	r = devm_acpi_dev_add_driver_gpios(dev, acpi_st_nci_gpios); | 
 | 	if (r) | 
 | 		dev_dbg(dev, "Unable to add GPIO mapping table\n"); | 
 |  | 
 | 	/* Get RESET GPIO */ | 
 | 	phy->gpiod_reset = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH); | 
 | 	if (IS_ERR(phy->gpiod_reset)) { | 
 | 		nfc_err(dev, "Unable to get RESET GPIO\n"); | 
 | 		return -ENODEV; | 
 | 	} | 
 |  | 
 | 	phy->se_status.is_ese_present = | 
 | 				device_property_read_bool(dev, "ese-present"); | 
 | 	phy->se_status.is_uicc_present = | 
 | 				device_property_read_bool(dev, "uicc-present"); | 
 |  | 
 | 	r = ndlc_probe(phy, &i2c_phy_ops, &client->dev, | 
 | 			ST_NCI_FRAME_HEADROOM, ST_NCI_FRAME_TAILROOM, | 
 | 			&phy->ndlc, &phy->se_status); | 
 | 	if (r < 0) { | 
 | 		nfc_err(&client->dev, "Unable to register ndlc layer\n"); | 
 | 		return r; | 
 | 	} | 
 |  | 
 | 	phy->irq_active = true; | 
 | 	r = devm_request_threaded_irq(&client->dev, client->irq, NULL, | 
 | 				st_nci_irq_thread_fn, | 
 | 				IRQF_ONESHOT, | 
 | 				ST_NCI_DRIVER_NAME, phy); | 
 | 	if (r < 0) | 
 | 		nfc_err(&client->dev, "Unable to register IRQ handler\n"); | 
 |  | 
 | 	return r; | 
 | } | 
 |  | 
 | static int st_nci_i2c_remove(struct i2c_client *client) | 
 | { | 
 | 	struct st_nci_i2c_phy *phy = i2c_get_clientdata(client); | 
 |  | 
 | 	dev_dbg(&client->dev, "%s\n", __func__); | 
 |  | 
 | 	ndlc_remove(phy->ndlc); | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | static const struct i2c_device_id st_nci_i2c_id_table[] = { | 
 | 	{ST_NCI_DRIVER_NAME, 0}, | 
 | 	{} | 
 | }; | 
 | MODULE_DEVICE_TABLE(i2c, st_nci_i2c_id_table); | 
 |  | 
 | static const struct acpi_device_id st_nci_i2c_acpi_match[] = { | 
 | 	{"SMO2101"}, | 
 | 	{"SMO2102"}, | 
 | 	{} | 
 | }; | 
 | MODULE_DEVICE_TABLE(acpi, st_nci_i2c_acpi_match); | 
 |  | 
 | static const struct of_device_id of_st_nci_i2c_match[] = { | 
 | 	{ .compatible = "st,st21nfcb-i2c", }, | 
 | 	{ .compatible = "st,st21nfcb_i2c", }, | 
 | 	{ .compatible = "st,st21nfcc-i2c", }, | 
 | 	{} | 
 | }; | 
 | MODULE_DEVICE_TABLE(of, of_st_nci_i2c_match); | 
 |  | 
 | static struct i2c_driver st_nci_i2c_driver = { | 
 | 	.driver = { | 
 | 		.name = ST_NCI_I2C_DRIVER_NAME, | 
 | 		.of_match_table = of_match_ptr(of_st_nci_i2c_match), | 
 | 		.acpi_match_table = ACPI_PTR(st_nci_i2c_acpi_match), | 
 | 	}, | 
 | 	.probe = st_nci_i2c_probe, | 
 | 	.id_table = st_nci_i2c_id_table, | 
 | 	.remove = st_nci_i2c_remove, | 
 | }; | 
 | module_i2c_driver(st_nci_i2c_driver); | 
 |  | 
 | MODULE_LICENSE("GPL"); | 
 | MODULE_DESCRIPTION(DRIVER_DESC); |