|  | /* | 
|  | * Driver for Microsemi VSC85xx PHYs | 
|  | * | 
|  | * Author: Nagaraju Lakkaraju | 
|  | * License: Dual MIT/GPL | 
|  | * Copyright (c) 2016 Microsemi Corporation | 
|  | */ | 
|  |  | 
|  | #include <linux/kernel.h> | 
|  | #include <linux/module.h> | 
|  | #include <linux/mdio.h> | 
|  | #include <linux/mii.h> | 
|  | #include <linux/phy.h> | 
|  | #include <linux/of.h> | 
|  | #include <linux/netdevice.h> | 
|  | #include <dt-bindings/net/mscc-phy-vsc8531.h> | 
|  |  | 
|  | enum rgmii_rx_clock_delay { | 
|  | RGMII_RX_CLK_DELAY_0_2_NS = 0, | 
|  | RGMII_RX_CLK_DELAY_0_8_NS = 1, | 
|  | RGMII_RX_CLK_DELAY_1_1_NS = 2, | 
|  | RGMII_RX_CLK_DELAY_1_7_NS = 3, | 
|  | RGMII_RX_CLK_DELAY_2_0_NS = 4, | 
|  | RGMII_RX_CLK_DELAY_2_3_NS = 5, | 
|  | RGMII_RX_CLK_DELAY_2_6_NS = 6, | 
|  | RGMII_RX_CLK_DELAY_3_4_NS = 7 | 
|  | }; | 
|  |  | 
|  | /* Microsemi VSC85xx PHY registers */ | 
|  | /* IEEE 802. Std Registers */ | 
|  | #define MSCC_PHY_BYPASS_CONTROL		  18 | 
|  | #define DISABLE_HP_AUTO_MDIX_MASK	  0x0080 | 
|  | #define DISABLE_PAIR_SWAP_CORR_MASK	  0x0020 | 
|  | #define DISABLE_POLARITY_CORR_MASK	  0x0010 | 
|  |  | 
|  | #define MSCC_PHY_EXT_PHY_CNTL_1           23 | 
|  | #define MAC_IF_SELECTION_MASK             0x1800 | 
|  | #define MAC_IF_SELECTION_GMII             0 | 
|  | #define MAC_IF_SELECTION_RMII             1 | 
|  | #define MAC_IF_SELECTION_RGMII            2 | 
|  | #define MAC_IF_SELECTION_POS              11 | 
|  | #define FAR_END_LOOPBACK_MODE_MASK        0x0008 | 
|  |  | 
|  | #define MII_VSC85XX_INT_MASK		  25 | 
|  | #define MII_VSC85XX_INT_MASK_MASK	  0xa000 | 
|  | #define MII_VSC85XX_INT_MASK_WOL	  0x0040 | 
|  | #define MII_VSC85XX_INT_STATUS		  26 | 
|  |  | 
|  | #define MSCC_PHY_WOL_MAC_CONTROL          27 | 
|  | #define EDGE_RATE_CNTL_POS                5 | 
|  | #define EDGE_RATE_CNTL_MASK               0x00E0 | 
|  |  | 
|  | #define MSCC_PHY_DEV_AUX_CNTL		  28 | 
|  | #define HP_AUTO_MDIX_X_OVER_IND_MASK	  0x2000 | 
|  |  | 
|  | #define MSCC_PHY_LED_MODE_SEL		  29 | 
|  | #define LED_1_MODE_SEL_MASK		  0x00F0 | 
|  | #define LED_0_MODE_SEL_MASK		  0x000F | 
|  | #define LED_1_MODE_SEL_POS		  4 | 
|  |  | 
|  | #define MSCC_EXT_PAGE_ACCESS		  31 | 
|  | #define MSCC_PHY_PAGE_STANDARD		  0x0000 /* Standard registers */ | 
|  | #define MSCC_PHY_PAGE_EXTENDED		  0x0001 /* Extended registers */ | 
|  | #define MSCC_PHY_PAGE_EXTENDED_2	  0x0002 /* Extended reg - page 2 */ | 
|  |  | 
|  | /* Extended Page 1 Registers */ | 
|  | #define MSCC_PHY_EXT_MODE_CNTL		  19 | 
|  | #define FORCE_MDI_CROSSOVER_MASK	  0x000C | 
|  | #define FORCE_MDI_CROSSOVER_MDIX	  0x000C | 
|  | #define FORCE_MDI_CROSSOVER_MDI		  0x0008 | 
|  |  | 
|  | #define MSCC_PHY_ACTIPHY_CNTL		  20 | 
|  | #define DOWNSHIFT_CNTL_MASK		  0x001C | 
|  | #define DOWNSHIFT_EN			  0x0010 | 
|  | #define DOWNSHIFT_CNTL_POS		  2 | 
|  |  | 
|  | /* Extended Page 2 Registers */ | 
|  | #define MSCC_PHY_RGMII_CNTL		  20 | 
|  | #define RGMII_RX_CLK_DELAY_MASK		  0x0070 | 
|  | #define RGMII_RX_CLK_DELAY_POS		  4 | 
|  |  | 
|  | #define MSCC_PHY_WOL_LOWER_MAC_ADDR	  21 | 
|  | #define MSCC_PHY_WOL_MID_MAC_ADDR	  22 | 
|  | #define MSCC_PHY_WOL_UPPER_MAC_ADDR	  23 | 
|  | #define MSCC_PHY_WOL_LOWER_PASSWD	  24 | 
|  | #define MSCC_PHY_WOL_MID_PASSWD		  25 | 
|  | #define MSCC_PHY_WOL_UPPER_PASSWD	  26 | 
|  |  | 
|  | #define MSCC_PHY_WOL_MAC_CONTROL	  27 | 
|  | #define SECURE_ON_ENABLE		  0x8000 | 
|  | #define SECURE_ON_PASSWD_LEN_4		  0x4000 | 
|  |  | 
|  | /* Microsemi PHY ID's */ | 
|  | #define PHY_ID_VSC8530			  0x00070560 | 
|  | #define PHY_ID_VSC8531			  0x00070570 | 
|  | #define PHY_ID_VSC8540			  0x00070760 | 
|  | #define PHY_ID_VSC8541			  0x00070770 | 
|  |  | 
|  | #define MSCC_VDDMAC_1500		  1500 | 
|  | #define MSCC_VDDMAC_1800		  1800 | 
|  | #define MSCC_VDDMAC_2500		  2500 | 
|  | #define MSCC_VDDMAC_3300		  3300 | 
|  |  | 
|  | #define DOWNSHIFT_COUNT_MAX		  5 | 
|  |  | 
|  | struct vsc8531_private { | 
|  | int rate_magic; | 
|  | u8 led_0_mode; | 
|  | u8 led_1_mode; | 
|  | }; | 
|  |  | 
|  | #ifdef CONFIG_OF_MDIO | 
|  | struct vsc8531_edge_rate_table { | 
|  | u32 vddmac; | 
|  | u32 slowdown[8]; | 
|  | }; | 
|  |  | 
|  | static const struct vsc8531_edge_rate_table edge_table[] = { | 
|  | {MSCC_VDDMAC_3300, { 0, 2,  4,  7, 10, 17, 29, 53} }, | 
|  | {MSCC_VDDMAC_2500, { 0, 3,  6, 10, 14, 23, 37, 63} }, | 
|  | {MSCC_VDDMAC_1800, { 0, 5,  9, 16, 23, 35, 52, 76} }, | 
|  | {MSCC_VDDMAC_1500, { 0, 6, 14, 21, 29, 42, 58, 77} }, | 
|  | }; | 
|  | #endif /* CONFIG_OF_MDIO */ | 
|  |  | 
|  | static int vsc85xx_phy_page_set(struct phy_device *phydev, u16 page) | 
|  | { | 
|  | int rc; | 
|  |  | 
|  | rc = phy_write(phydev, MSCC_EXT_PAGE_ACCESS, page); | 
|  | return rc; | 
|  | } | 
|  |  | 
|  | static int vsc85xx_led_cntl_set(struct phy_device *phydev, | 
|  | u8 led_num, | 
|  | u8 mode) | 
|  | { | 
|  | int rc; | 
|  | u16 reg_val; | 
|  |  | 
|  | mutex_lock(&phydev->lock); | 
|  | reg_val = phy_read(phydev, MSCC_PHY_LED_MODE_SEL); | 
|  | if (led_num) { | 
|  | reg_val &= ~LED_1_MODE_SEL_MASK; | 
|  | reg_val |= (((u16)mode << LED_1_MODE_SEL_POS) & | 
|  | LED_1_MODE_SEL_MASK); | 
|  | } else { | 
|  | reg_val &= ~LED_0_MODE_SEL_MASK; | 
|  | reg_val |= ((u16)mode & LED_0_MODE_SEL_MASK); | 
|  | } | 
|  | rc = phy_write(phydev, MSCC_PHY_LED_MODE_SEL, reg_val); | 
|  | mutex_unlock(&phydev->lock); | 
|  |  | 
|  | return rc; | 
|  | } | 
|  |  | 
|  | static int vsc85xx_mdix_get(struct phy_device *phydev, u8 *mdix) | 
|  | { | 
|  | u16 reg_val; | 
|  |  | 
|  | reg_val = phy_read(phydev, MSCC_PHY_DEV_AUX_CNTL); | 
|  | if (reg_val & HP_AUTO_MDIX_X_OVER_IND_MASK) | 
|  | *mdix = ETH_TP_MDI_X; | 
|  | else | 
|  | *mdix = ETH_TP_MDI; | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int vsc85xx_mdix_set(struct phy_device *phydev, u8 mdix) | 
|  | { | 
|  | int rc; | 
|  | u16 reg_val; | 
|  |  | 
|  | reg_val = phy_read(phydev, MSCC_PHY_BYPASS_CONTROL); | 
|  | if ((mdix == ETH_TP_MDI) || (mdix == ETH_TP_MDI_X)) { | 
|  | reg_val |= (DISABLE_PAIR_SWAP_CORR_MASK | | 
|  | DISABLE_POLARITY_CORR_MASK  | | 
|  | DISABLE_HP_AUTO_MDIX_MASK); | 
|  | } else { | 
|  | reg_val &= ~(DISABLE_PAIR_SWAP_CORR_MASK | | 
|  | DISABLE_POLARITY_CORR_MASK  | | 
|  | DISABLE_HP_AUTO_MDIX_MASK); | 
|  | } | 
|  | rc = phy_write(phydev, MSCC_PHY_BYPASS_CONTROL, reg_val); | 
|  | if (rc != 0) | 
|  | return rc; | 
|  |  | 
|  | rc = vsc85xx_phy_page_set(phydev, MSCC_PHY_PAGE_EXTENDED); | 
|  | if (rc != 0) | 
|  | return rc; | 
|  |  | 
|  | reg_val = phy_read(phydev, MSCC_PHY_EXT_MODE_CNTL); | 
|  | reg_val &= ~(FORCE_MDI_CROSSOVER_MASK); | 
|  | if (mdix == ETH_TP_MDI) | 
|  | reg_val |= FORCE_MDI_CROSSOVER_MDI; | 
|  | else if (mdix == ETH_TP_MDI_X) | 
|  | reg_val |= FORCE_MDI_CROSSOVER_MDIX; | 
|  | rc = phy_write(phydev, MSCC_PHY_EXT_MODE_CNTL, reg_val); | 
|  | if (rc != 0) | 
|  | return rc; | 
|  |  | 
|  | rc = vsc85xx_phy_page_set(phydev, MSCC_PHY_PAGE_STANDARD); | 
|  | if (rc != 0) | 
|  | return rc; | 
|  |  | 
|  | return genphy_restart_aneg(phydev); | 
|  | } | 
|  |  | 
|  | static int vsc85xx_downshift_get(struct phy_device *phydev, u8 *count) | 
|  | { | 
|  | int rc; | 
|  | u16 reg_val; | 
|  |  | 
|  | rc = vsc85xx_phy_page_set(phydev, MSCC_PHY_PAGE_EXTENDED); | 
|  | if (rc != 0) | 
|  | goto out; | 
|  |  | 
|  | reg_val = phy_read(phydev, MSCC_PHY_ACTIPHY_CNTL); | 
|  | reg_val &= DOWNSHIFT_CNTL_MASK; | 
|  | if (!(reg_val & DOWNSHIFT_EN)) | 
|  | *count = DOWNSHIFT_DEV_DISABLE; | 
|  | else | 
|  | *count = ((reg_val & ~DOWNSHIFT_EN) >> DOWNSHIFT_CNTL_POS) + 2; | 
|  | rc = vsc85xx_phy_page_set(phydev, MSCC_PHY_PAGE_STANDARD); | 
|  |  | 
|  | out: | 
|  | return rc; | 
|  | } | 
|  |  | 
|  | static int vsc85xx_downshift_set(struct phy_device *phydev, u8 count) | 
|  | { | 
|  | int rc; | 
|  | u16 reg_val; | 
|  |  | 
|  | if (count == DOWNSHIFT_DEV_DEFAULT_COUNT) { | 
|  | /* Default downshift count 3 (i.e. Bit3:2 = 0b01) */ | 
|  | count = ((1 << DOWNSHIFT_CNTL_POS) | DOWNSHIFT_EN); | 
|  | } else if (count > DOWNSHIFT_COUNT_MAX || count == 1) { | 
|  | phydev_err(phydev, "Downshift count should be 2,3,4 or 5\n"); | 
|  | return -ERANGE; | 
|  | } else if (count) { | 
|  | /* Downshift count is either 2,3,4 or 5 */ | 
|  | count = (((count - 2) << DOWNSHIFT_CNTL_POS) | DOWNSHIFT_EN); | 
|  | } | 
|  |  | 
|  | rc = vsc85xx_phy_page_set(phydev, MSCC_PHY_PAGE_EXTENDED); | 
|  | if (rc != 0) | 
|  | goto out; | 
|  |  | 
|  | reg_val = phy_read(phydev, MSCC_PHY_ACTIPHY_CNTL); | 
|  | reg_val &= ~(DOWNSHIFT_CNTL_MASK); | 
|  | reg_val |= count; | 
|  | rc = phy_write(phydev, MSCC_PHY_ACTIPHY_CNTL, reg_val); | 
|  | if (rc != 0) | 
|  | goto out; | 
|  |  | 
|  | rc = vsc85xx_phy_page_set(phydev, MSCC_PHY_PAGE_STANDARD); | 
|  |  | 
|  | out: | 
|  | return rc; | 
|  | } | 
|  |  | 
|  | static int vsc85xx_wol_set(struct phy_device *phydev, | 
|  | struct ethtool_wolinfo *wol) | 
|  | { | 
|  | int rc; | 
|  | u16 reg_val; | 
|  | u8  i; | 
|  | u16 pwd[3] = {0, 0, 0}; | 
|  | struct ethtool_wolinfo *wol_conf = wol; | 
|  | u8 *mac_addr = phydev->attached_dev->dev_addr; | 
|  |  | 
|  | mutex_lock(&phydev->lock); | 
|  | rc = vsc85xx_phy_page_set(phydev, MSCC_PHY_PAGE_EXTENDED_2); | 
|  | if (rc != 0) | 
|  | goto out_unlock; | 
|  |  | 
|  | if (wol->wolopts & WAKE_MAGIC) { | 
|  | /* Store the device address for the magic packet */ | 
|  | for (i = 0; i < ARRAY_SIZE(pwd); i++) | 
|  | pwd[i] = mac_addr[5 - (i * 2 + 1)] << 8 | | 
|  | mac_addr[5 - i * 2]; | 
|  | phy_write(phydev, MSCC_PHY_WOL_LOWER_MAC_ADDR, pwd[0]); | 
|  | phy_write(phydev, MSCC_PHY_WOL_MID_MAC_ADDR, pwd[1]); | 
|  | phy_write(phydev, MSCC_PHY_WOL_UPPER_MAC_ADDR, pwd[2]); | 
|  | } else { | 
|  | phy_write(phydev, MSCC_PHY_WOL_LOWER_MAC_ADDR, 0); | 
|  | phy_write(phydev, MSCC_PHY_WOL_MID_MAC_ADDR, 0); | 
|  | phy_write(phydev, MSCC_PHY_WOL_UPPER_MAC_ADDR, 0); | 
|  | } | 
|  |  | 
|  | if (wol_conf->wolopts & WAKE_MAGICSECURE) { | 
|  | for (i = 0; i < ARRAY_SIZE(pwd); i++) | 
|  | pwd[i] = wol_conf->sopass[5 - (i * 2 + 1)] << 8 | | 
|  | wol_conf->sopass[5 - i * 2]; | 
|  | phy_write(phydev, MSCC_PHY_WOL_LOWER_PASSWD, pwd[0]); | 
|  | phy_write(phydev, MSCC_PHY_WOL_MID_PASSWD, pwd[1]); | 
|  | phy_write(phydev, MSCC_PHY_WOL_UPPER_PASSWD, pwd[2]); | 
|  | } else { | 
|  | phy_write(phydev, MSCC_PHY_WOL_LOWER_PASSWD, 0); | 
|  | phy_write(phydev, MSCC_PHY_WOL_MID_PASSWD, 0); | 
|  | phy_write(phydev, MSCC_PHY_WOL_UPPER_PASSWD, 0); | 
|  | } | 
|  |  | 
|  | reg_val = phy_read(phydev, MSCC_PHY_WOL_MAC_CONTROL); | 
|  | if (wol_conf->wolopts & WAKE_MAGICSECURE) | 
|  | reg_val |= SECURE_ON_ENABLE; | 
|  | else | 
|  | reg_val &= ~SECURE_ON_ENABLE; | 
|  | phy_write(phydev, MSCC_PHY_WOL_MAC_CONTROL, reg_val); | 
|  |  | 
|  | rc = vsc85xx_phy_page_set(phydev, MSCC_PHY_PAGE_STANDARD); | 
|  | if (rc != 0) | 
|  | goto out_unlock; | 
|  |  | 
|  | if (wol->wolopts & WAKE_MAGIC) { | 
|  | /* Enable the WOL interrupt */ | 
|  | reg_val = phy_read(phydev, MII_VSC85XX_INT_MASK); | 
|  | reg_val |= MII_VSC85XX_INT_MASK_WOL; | 
|  | rc = phy_write(phydev, MII_VSC85XX_INT_MASK, reg_val); | 
|  | if (rc != 0) | 
|  | goto out_unlock; | 
|  | } else { | 
|  | /* Disable the WOL interrupt */ | 
|  | reg_val = phy_read(phydev, MII_VSC85XX_INT_MASK); | 
|  | reg_val &= (~MII_VSC85XX_INT_MASK_WOL); | 
|  | rc = phy_write(phydev, MII_VSC85XX_INT_MASK, reg_val); | 
|  | if (rc != 0) | 
|  | goto out_unlock; | 
|  | } | 
|  | /* Clear WOL iterrupt status */ | 
|  | reg_val = phy_read(phydev, MII_VSC85XX_INT_STATUS); | 
|  |  | 
|  | out_unlock: | 
|  | mutex_unlock(&phydev->lock); | 
|  |  | 
|  | return rc; | 
|  | } | 
|  |  | 
|  | static void vsc85xx_wol_get(struct phy_device *phydev, | 
|  | struct ethtool_wolinfo *wol) | 
|  | { | 
|  | int rc; | 
|  | u16 reg_val; | 
|  | u8  i; | 
|  | u16 pwd[3] = {0, 0, 0}; | 
|  | struct ethtool_wolinfo *wol_conf = wol; | 
|  |  | 
|  | mutex_lock(&phydev->lock); | 
|  | rc = vsc85xx_phy_page_set(phydev, MSCC_PHY_PAGE_EXTENDED_2); | 
|  | if (rc != 0) | 
|  | goto out_unlock; | 
|  |  | 
|  | reg_val = phy_read(phydev, MSCC_PHY_WOL_MAC_CONTROL); | 
|  | if (reg_val & SECURE_ON_ENABLE) | 
|  | wol_conf->wolopts |= WAKE_MAGICSECURE; | 
|  | if (wol_conf->wolopts & WAKE_MAGICSECURE) { | 
|  | pwd[0] = phy_read(phydev, MSCC_PHY_WOL_LOWER_PASSWD); | 
|  | pwd[1] = phy_read(phydev, MSCC_PHY_WOL_MID_PASSWD); | 
|  | pwd[2] = phy_read(phydev, MSCC_PHY_WOL_UPPER_PASSWD); | 
|  | for (i = 0; i < ARRAY_SIZE(pwd); i++) { | 
|  | wol_conf->sopass[5 - i * 2] = pwd[i] & 0x00ff; | 
|  | wol_conf->sopass[5 - (i * 2 + 1)] = (pwd[i] & 0xff00) | 
|  | >> 8; | 
|  | } | 
|  | } | 
|  |  | 
|  | rc = vsc85xx_phy_page_set(phydev, MSCC_PHY_PAGE_STANDARD); | 
|  |  | 
|  | out_unlock: | 
|  | mutex_unlock(&phydev->lock); | 
|  | } | 
|  |  | 
|  | #ifdef CONFIG_OF_MDIO | 
|  | static int vsc85xx_edge_rate_magic_get(struct phy_device *phydev) | 
|  | { | 
|  | u32 vdd, sd; | 
|  | int rc, i, j; | 
|  | struct device *dev = &phydev->mdio.dev; | 
|  | struct device_node *of_node = dev->of_node; | 
|  | u8 sd_array_size = ARRAY_SIZE(edge_table[0].slowdown); | 
|  |  | 
|  | if (!of_node) | 
|  | return -ENODEV; | 
|  |  | 
|  | rc = of_property_read_u32(of_node, "vsc8531,vddmac", &vdd); | 
|  | if (rc != 0) | 
|  | vdd = MSCC_VDDMAC_3300; | 
|  |  | 
|  | rc = of_property_read_u32(of_node, "vsc8531,edge-slowdown", &sd); | 
|  | if (rc != 0) | 
|  | sd = 0; | 
|  |  | 
|  | for (i = 0; i < ARRAY_SIZE(edge_table); i++) | 
|  | if (edge_table[i].vddmac == vdd) | 
|  | for (j = 0; j < sd_array_size; j++) | 
|  | if (edge_table[i].slowdown[j] == sd) | 
|  | return (sd_array_size - j - 1); | 
|  |  | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | static int vsc85xx_dt_led_mode_get(struct phy_device *phydev, | 
|  | char *led, | 
|  | u8 default_mode) | 
|  | { | 
|  | struct device *dev = &phydev->mdio.dev; | 
|  | struct device_node *of_node = dev->of_node; | 
|  | u8 led_mode; | 
|  | int err; | 
|  |  | 
|  | if (!of_node) | 
|  | return -ENODEV; | 
|  |  | 
|  | led_mode = default_mode; | 
|  | err = of_property_read_u8(of_node, led, &led_mode); | 
|  | if (!err && (led_mode > 15 || led_mode == 7 || led_mode == 11)) { | 
|  | phydev_err(phydev, "DT %s invalid\n", led); | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | return led_mode; | 
|  | } | 
|  |  | 
|  | #else | 
|  | static int vsc85xx_edge_rate_magic_get(struct phy_device *phydev) | 
|  | { | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int vsc85xx_dt_led_mode_get(struct phy_device *phydev, | 
|  | char *led, | 
|  | u8 default_mode) | 
|  | { | 
|  | return default_mode; | 
|  | } | 
|  | #endif /* CONFIG_OF_MDIO */ | 
|  |  | 
|  | static int vsc85xx_edge_rate_cntl_set(struct phy_device *phydev, u8 edge_rate) | 
|  | { | 
|  | int rc; | 
|  | u16 reg_val; | 
|  |  | 
|  | mutex_lock(&phydev->lock); | 
|  | rc = vsc85xx_phy_page_set(phydev, MSCC_PHY_PAGE_EXTENDED_2); | 
|  | if (rc != 0) | 
|  | goto out_unlock; | 
|  | reg_val = phy_read(phydev, MSCC_PHY_WOL_MAC_CONTROL); | 
|  | reg_val &= ~(EDGE_RATE_CNTL_MASK); | 
|  | reg_val |= (edge_rate << EDGE_RATE_CNTL_POS); | 
|  | rc = phy_write(phydev, MSCC_PHY_WOL_MAC_CONTROL, reg_val); | 
|  | if (rc != 0) | 
|  | goto out_unlock; | 
|  | rc = vsc85xx_phy_page_set(phydev, MSCC_PHY_PAGE_STANDARD); | 
|  |  | 
|  | out_unlock: | 
|  | mutex_unlock(&phydev->lock); | 
|  |  | 
|  | return rc; | 
|  | } | 
|  |  | 
|  | static int vsc85xx_mac_if_set(struct phy_device *phydev, | 
|  | phy_interface_t interface) | 
|  | { | 
|  | int rc; | 
|  | u16 reg_val; | 
|  |  | 
|  | mutex_lock(&phydev->lock); | 
|  | reg_val = phy_read(phydev, MSCC_PHY_EXT_PHY_CNTL_1); | 
|  | reg_val &= ~(MAC_IF_SELECTION_MASK); | 
|  | switch (interface) { | 
|  | case PHY_INTERFACE_MODE_RGMII: | 
|  | reg_val |= (MAC_IF_SELECTION_RGMII << MAC_IF_SELECTION_POS); | 
|  | break; | 
|  | case PHY_INTERFACE_MODE_RMII: | 
|  | reg_val |= (MAC_IF_SELECTION_RMII << MAC_IF_SELECTION_POS); | 
|  | break; | 
|  | case PHY_INTERFACE_MODE_MII: | 
|  | case PHY_INTERFACE_MODE_GMII: | 
|  | reg_val |= (MAC_IF_SELECTION_GMII << MAC_IF_SELECTION_POS); | 
|  | break; | 
|  | default: | 
|  | rc = -EINVAL; | 
|  | goto out_unlock; | 
|  | } | 
|  | rc = phy_write(phydev, MSCC_PHY_EXT_PHY_CNTL_1, reg_val); | 
|  | if (rc != 0) | 
|  | goto out_unlock; | 
|  |  | 
|  | rc = genphy_soft_reset(phydev); | 
|  |  | 
|  | out_unlock: | 
|  | mutex_unlock(&phydev->lock); | 
|  |  | 
|  | return rc; | 
|  | } | 
|  |  | 
|  | static int vsc85xx_default_config(struct phy_device *phydev) | 
|  | { | 
|  | int rc; | 
|  | u16 reg_val; | 
|  |  | 
|  | phydev->mdix_ctrl = ETH_TP_MDI_AUTO; | 
|  | mutex_lock(&phydev->lock); | 
|  | rc = vsc85xx_phy_page_set(phydev, MSCC_PHY_PAGE_EXTENDED_2); | 
|  | if (rc != 0) | 
|  | goto out_unlock; | 
|  |  | 
|  | reg_val = phy_read(phydev, MSCC_PHY_RGMII_CNTL); | 
|  | reg_val &= ~(RGMII_RX_CLK_DELAY_MASK); | 
|  | reg_val |= (RGMII_RX_CLK_DELAY_1_1_NS << RGMII_RX_CLK_DELAY_POS); | 
|  | phy_write(phydev, MSCC_PHY_RGMII_CNTL, reg_val); | 
|  | rc = vsc85xx_phy_page_set(phydev, MSCC_PHY_PAGE_STANDARD); | 
|  |  | 
|  | out_unlock: | 
|  | mutex_unlock(&phydev->lock); | 
|  |  | 
|  | return rc; | 
|  | } | 
|  |  | 
|  | static int vsc85xx_get_tunable(struct phy_device *phydev, | 
|  | struct ethtool_tunable *tuna, void *data) | 
|  | { | 
|  | switch (tuna->id) { | 
|  | case ETHTOOL_PHY_DOWNSHIFT: | 
|  | return vsc85xx_downshift_get(phydev, (u8 *)data); | 
|  | default: | 
|  | return -EINVAL; | 
|  | } | 
|  | } | 
|  |  | 
|  | static int vsc85xx_set_tunable(struct phy_device *phydev, | 
|  | struct ethtool_tunable *tuna, | 
|  | const void *data) | 
|  | { | 
|  | switch (tuna->id) { | 
|  | case ETHTOOL_PHY_DOWNSHIFT: | 
|  | return vsc85xx_downshift_set(phydev, *(u8 *)data); | 
|  | default: | 
|  | return -EINVAL; | 
|  | } | 
|  | } | 
|  |  | 
|  | static int vsc85xx_config_init(struct phy_device *phydev) | 
|  | { | 
|  | int rc; | 
|  | struct vsc8531_private *vsc8531 = phydev->priv; | 
|  |  | 
|  | rc = vsc85xx_default_config(phydev); | 
|  | if (rc) | 
|  | return rc; | 
|  |  | 
|  | rc = vsc85xx_mac_if_set(phydev, phydev->interface); | 
|  | if (rc) | 
|  | return rc; | 
|  |  | 
|  | rc = vsc85xx_edge_rate_cntl_set(phydev, vsc8531->rate_magic); | 
|  | if (rc) | 
|  | return rc; | 
|  |  | 
|  | rc = vsc85xx_led_cntl_set(phydev, 1, vsc8531->led_1_mode); | 
|  | if (rc) | 
|  | return rc; | 
|  |  | 
|  | rc = vsc85xx_led_cntl_set(phydev, 0, vsc8531->led_0_mode); | 
|  | if (rc) | 
|  | return rc; | 
|  |  | 
|  | rc = genphy_config_init(phydev); | 
|  |  | 
|  | return rc; | 
|  | } | 
|  |  | 
|  | static int vsc85xx_ack_interrupt(struct phy_device *phydev) | 
|  | { | 
|  | int rc = 0; | 
|  |  | 
|  | if (phydev->interrupts == PHY_INTERRUPT_ENABLED) | 
|  | rc = phy_read(phydev, MII_VSC85XX_INT_STATUS); | 
|  |  | 
|  | return (rc < 0) ? rc : 0; | 
|  | } | 
|  |  | 
|  | static int vsc85xx_config_intr(struct phy_device *phydev) | 
|  | { | 
|  | int rc; | 
|  |  | 
|  | if (phydev->interrupts == PHY_INTERRUPT_ENABLED) { | 
|  | rc = phy_write(phydev, MII_VSC85XX_INT_MASK, | 
|  | MII_VSC85XX_INT_MASK_MASK); | 
|  | } else { | 
|  | rc = phy_write(phydev, MII_VSC85XX_INT_MASK, 0); | 
|  | if (rc < 0) | 
|  | return rc; | 
|  | rc = phy_read(phydev, MII_VSC85XX_INT_STATUS); | 
|  | } | 
|  |  | 
|  | return rc; | 
|  | } | 
|  |  | 
|  | static int vsc85xx_config_aneg(struct phy_device *phydev) | 
|  | { | 
|  | int rc; | 
|  |  | 
|  | rc = vsc85xx_mdix_set(phydev, phydev->mdix_ctrl); | 
|  | if (rc < 0) | 
|  | return rc; | 
|  |  | 
|  | return genphy_config_aneg(phydev); | 
|  | } | 
|  |  | 
|  | static int vsc85xx_read_status(struct phy_device *phydev) | 
|  | { | 
|  | int rc; | 
|  |  | 
|  | rc = vsc85xx_mdix_get(phydev, &phydev->mdix); | 
|  | if (rc < 0) | 
|  | return rc; | 
|  |  | 
|  | return genphy_read_status(phydev); | 
|  | } | 
|  |  | 
|  | static int vsc85xx_probe(struct phy_device *phydev) | 
|  | { | 
|  | struct vsc8531_private *vsc8531; | 
|  | int rate_magic; | 
|  | int led_mode; | 
|  |  | 
|  | rate_magic = vsc85xx_edge_rate_magic_get(phydev); | 
|  | if (rate_magic < 0) | 
|  | return rate_magic; | 
|  |  | 
|  | vsc8531 = devm_kzalloc(&phydev->mdio.dev, sizeof(*vsc8531), GFP_KERNEL); | 
|  | if (!vsc8531) | 
|  | return -ENOMEM; | 
|  |  | 
|  | phydev->priv = vsc8531; | 
|  |  | 
|  | vsc8531->rate_magic = rate_magic; | 
|  |  | 
|  | /* LED[0] and LED[1] mode */ | 
|  | led_mode = vsc85xx_dt_led_mode_get(phydev, "vsc8531,led-0-mode", | 
|  | VSC8531_LINK_1000_ACTIVITY); | 
|  | if (led_mode < 0) | 
|  | return led_mode; | 
|  | vsc8531->led_0_mode = led_mode; | 
|  |  | 
|  | led_mode = vsc85xx_dt_led_mode_get(phydev, "vsc8531,led-1-mode", | 
|  | VSC8531_LINK_100_ACTIVITY); | 
|  | if (led_mode < 0) | 
|  | return led_mode; | 
|  | vsc8531->led_1_mode = led_mode; | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | /* Microsemi VSC85xx PHYs */ | 
|  | static struct phy_driver vsc85xx_driver[] = { | 
|  | { | 
|  | .phy_id		= PHY_ID_VSC8530, | 
|  | .name		= "Microsemi FE VSC8530", | 
|  | .phy_id_mask	= 0xfffffff0, | 
|  | .features	= PHY_BASIC_FEATURES, | 
|  | .flags		= PHY_HAS_INTERRUPT, | 
|  | .soft_reset	= &genphy_soft_reset, | 
|  | .config_init	= &vsc85xx_config_init, | 
|  | .config_aneg    = &vsc85xx_config_aneg, | 
|  | .aneg_done	= &genphy_aneg_done, | 
|  | .read_status	= &vsc85xx_read_status, | 
|  | .ack_interrupt	= &vsc85xx_ack_interrupt, | 
|  | .config_intr	= &vsc85xx_config_intr, | 
|  | .suspend	= &genphy_suspend, | 
|  | .resume		= &genphy_resume, | 
|  | .probe		= &vsc85xx_probe, | 
|  | .set_wol	= &vsc85xx_wol_set, | 
|  | .get_wol	= &vsc85xx_wol_get, | 
|  | .get_tunable	= &vsc85xx_get_tunable, | 
|  | .set_tunable	= &vsc85xx_set_tunable, | 
|  | }, | 
|  | { | 
|  | .phy_id		= PHY_ID_VSC8531, | 
|  | .name		= "Microsemi VSC8531", | 
|  | .phy_id_mask    = 0xfffffff0, | 
|  | .features	= PHY_GBIT_FEATURES, | 
|  | .flags		= PHY_HAS_INTERRUPT, | 
|  | .soft_reset	= &genphy_soft_reset, | 
|  | .config_init    = &vsc85xx_config_init, | 
|  | .config_aneg    = &vsc85xx_config_aneg, | 
|  | .aneg_done	= &genphy_aneg_done, | 
|  | .read_status	= &vsc85xx_read_status, | 
|  | .ack_interrupt  = &vsc85xx_ack_interrupt, | 
|  | .config_intr    = &vsc85xx_config_intr, | 
|  | .suspend	= &genphy_suspend, | 
|  | .resume		= &genphy_resume, | 
|  | .probe		= &vsc85xx_probe, | 
|  | .set_wol	= &vsc85xx_wol_set, | 
|  | .get_wol	= &vsc85xx_wol_get, | 
|  | .get_tunable	= &vsc85xx_get_tunable, | 
|  | .set_tunable	= &vsc85xx_set_tunable, | 
|  | }, | 
|  | { | 
|  | .phy_id		= PHY_ID_VSC8540, | 
|  | .name		= "Microsemi FE VSC8540 SyncE", | 
|  | .phy_id_mask	= 0xfffffff0, | 
|  | .features	= PHY_BASIC_FEATURES, | 
|  | .flags		= PHY_HAS_INTERRUPT, | 
|  | .soft_reset	= &genphy_soft_reset, | 
|  | .config_init	= &vsc85xx_config_init, | 
|  | .config_aneg	= &vsc85xx_config_aneg, | 
|  | .aneg_done	= &genphy_aneg_done, | 
|  | .read_status	= &vsc85xx_read_status, | 
|  | .ack_interrupt	= &vsc85xx_ack_interrupt, | 
|  | .config_intr	= &vsc85xx_config_intr, | 
|  | .suspend	= &genphy_suspend, | 
|  | .resume		= &genphy_resume, | 
|  | .probe		= &vsc85xx_probe, | 
|  | .set_wol	= &vsc85xx_wol_set, | 
|  | .get_wol	= &vsc85xx_wol_get, | 
|  | .get_tunable	= &vsc85xx_get_tunable, | 
|  | .set_tunable	= &vsc85xx_set_tunable, | 
|  | }, | 
|  | { | 
|  | .phy_id		= PHY_ID_VSC8541, | 
|  | .name		= "Microsemi VSC8541 SyncE", | 
|  | .phy_id_mask    = 0xfffffff0, | 
|  | .features	= PHY_GBIT_FEATURES, | 
|  | .flags		= PHY_HAS_INTERRUPT, | 
|  | .soft_reset	= &genphy_soft_reset, | 
|  | .config_init    = &vsc85xx_config_init, | 
|  | .config_aneg    = &vsc85xx_config_aneg, | 
|  | .aneg_done	= &genphy_aneg_done, | 
|  | .read_status	= &vsc85xx_read_status, | 
|  | .ack_interrupt  = &vsc85xx_ack_interrupt, | 
|  | .config_intr    = &vsc85xx_config_intr, | 
|  | .suspend	= &genphy_suspend, | 
|  | .resume		= &genphy_resume, | 
|  | .probe		= &vsc85xx_probe, | 
|  | .set_wol	= &vsc85xx_wol_set, | 
|  | .get_wol	= &vsc85xx_wol_get, | 
|  | .get_tunable	= &vsc85xx_get_tunable, | 
|  | .set_tunable	= &vsc85xx_set_tunable, | 
|  | } | 
|  |  | 
|  | }; | 
|  |  | 
|  | module_phy_driver(vsc85xx_driver); | 
|  |  | 
|  | static struct mdio_device_id __maybe_unused vsc85xx_tbl[] = { | 
|  | { PHY_ID_VSC8530, 0xfffffff0, }, | 
|  | { PHY_ID_VSC8531, 0xfffffff0, }, | 
|  | { PHY_ID_VSC8540, 0xfffffff0, }, | 
|  | { PHY_ID_VSC8541, 0xfffffff0, }, | 
|  | { } | 
|  | }; | 
|  |  | 
|  | MODULE_DEVICE_TABLE(mdio, vsc85xx_tbl); | 
|  |  | 
|  | MODULE_DESCRIPTION("Microsemi VSC85xx PHY driver"); | 
|  | MODULE_AUTHOR("Nagaraju Lakkaraju"); | 
|  | MODULE_LICENSE("Dual MIT/GPL"); |