|  | // SPDX-License-Identifier: GPL-2.0 | 
|  | /* | 
|  | * Copyright (C) 2010 Google, Inc. | 
|  | * Copyright (C) 2013 NVIDIA Corporation | 
|  | * | 
|  | * Author: | 
|  | *	Erik Gilling <konkers@google.com> | 
|  | *	Benoit Goby <benoit@android.com> | 
|  | *	Venu Byravarasu <vbyravarasu@nvidia.com> | 
|  | */ | 
|  |  | 
|  | #include <linux/resource.h> | 
|  | #include <linux/delay.h> | 
|  | #include <linux/slab.h> | 
|  | #include <linux/err.h> | 
|  | #include <linux/export.h> | 
|  | #include <linux/module.h> | 
|  | #include <linux/platform_device.h> | 
|  | #include <linux/iopoll.h> | 
|  | #include <linux/gpio.h> | 
|  | #include <linux/of.h> | 
|  | #include <linux/of_device.h> | 
|  | #include <linux/of_gpio.h> | 
|  | #include <linux/usb/otg.h> | 
|  | #include <linux/usb/ulpi.h> | 
|  | #include <linux/usb/of.h> | 
|  | #include <linux/usb/ehci_def.h> | 
|  | #include <linux/usb/tegra_usb_phy.h> | 
|  | #include <linux/regulator/consumer.h> | 
|  |  | 
|  | #define ULPI_VIEWPORT		0x170 | 
|  |  | 
|  | /* PORTSC PTS/PHCD bits, Tegra20 only */ | 
|  | #define TEGRA_USB_PORTSC1				0x184 | 
|  | #define TEGRA_USB_PORTSC1_PTS(x)			(((x) & 0x3) << 30) | 
|  | #define TEGRA_USB_PORTSC1_PHCD				(1 << 23) | 
|  |  | 
|  | /* HOSTPC1 PTS/PHCD bits, Tegra30 and above */ | 
|  | #define TEGRA_USB_HOSTPC1_DEVLC		0x1b4 | 
|  | #define TEGRA_USB_HOSTPC1_DEVLC_PTS(x)	(((x) & 0x7) << 29) | 
|  | #define TEGRA_USB_HOSTPC1_DEVLC_PHCD	(1 << 22) | 
|  |  | 
|  | /* Bits of PORTSC1, which will get cleared by writing 1 into them */ | 
|  | #define TEGRA_PORTSC1_RWC_BITS	(PORT_CSC | PORT_PEC | PORT_OCC) | 
|  |  | 
|  | #define USB_SUSP_CTRL		0x400 | 
|  | #define   USB_WAKE_ON_CNNT_EN_DEV	(1 << 3) | 
|  | #define   USB_WAKE_ON_DISCON_EN_DEV	(1 << 4) | 
|  | #define   USB_SUSP_CLR		(1 << 5) | 
|  | #define   USB_PHY_CLK_VALID	(1 << 7) | 
|  | #define   UTMIP_RESET			(1 << 11) | 
|  | #define   UHSIC_RESET			(1 << 11) | 
|  | #define   UTMIP_PHY_ENABLE		(1 << 12) | 
|  | #define   ULPI_PHY_ENABLE	(1 << 13) | 
|  | #define   USB_SUSP_SET		(1 << 14) | 
|  | #define   USB_WAKEUP_DEBOUNCE_COUNT(x)	(((x) & 0x7) << 16) | 
|  |  | 
|  | #define USB1_LEGACY_CTRL	0x410 | 
|  | #define   USB1_NO_LEGACY_MODE			(1 << 0) | 
|  | #define   USB1_VBUS_SENSE_CTL_MASK		(3 << 1) | 
|  | #define   USB1_VBUS_SENSE_CTL_VBUS_WAKEUP	(0 << 1) | 
|  | #define   USB1_VBUS_SENSE_CTL_AB_SESS_VLD_OR_VBUS_WAKEUP \ | 
|  | (1 << 1) | 
|  | #define   USB1_VBUS_SENSE_CTL_AB_SESS_VLD	(2 << 1) | 
|  | #define   USB1_VBUS_SENSE_CTL_A_SESS_VLD	(3 << 1) | 
|  |  | 
|  | #define ULPI_TIMING_CTRL_0	0x424 | 
|  | #define   ULPI_OUTPUT_PINMUX_BYP	(1 << 10) | 
|  | #define   ULPI_CLKOUT_PINMUX_BYP	(1 << 11) | 
|  |  | 
|  | #define ULPI_TIMING_CTRL_1	0x428 | 
|  | #define   ULPI_DATA_TRIMMER_LOAD	(1 << 0) | 
|  | #define   ULPI_DATA_TRIMMER_SEL(x)	(((x) & 0x7) << 1) | 
|  | #define   ULPI_STPDIRNXT_TRIMMER_LOAD	(1 << 16) | 
|  | #define   ULPI_STPDIRNXT_TRIMMER_SEL(x)	(((x) & 0x7) << 17) | 
|  | #define   ULPI_DIR_TRIMMER_LOAD		(1 << 24) | 
|  | #define   ULPI_DIR_TRIMMER_SEL(x)	(((x) & 0x7) << 25) | 
|  |  | 
|  | #define UTMIP_PLL_CFG1		0x804 | 
|  | #define   UTMIP_XTAL_FREQ_COUNT(x)		(((x) & 0xfff) << 0) | 
|  | #define   UTMIP_PLLU_ENABLE_DLY_COUNT(x)	(((x) & 0x1f) << 27) | 
|  |  | 
|  | #define UTMIP_XCVR_CFG0		0x808 | 
|  | #define   UTMIP_XCVR_SETUP(x)			(((x) & 0xf) << 0) | 
|  | #define   UTMIP_XCVR_SETUP_MSB(x)		((((x) & 0x70) >> 4) << 22) | 
|  | #define   UTMIP_XCVR_LSRSLEW(x)			(((x) & 0x3) << 8) | 
|  | #define   UTMIP_XCVR_LSFSLEW(x)			(((x) & 0x3) << 10) | 
|  | #define   UTMIP_FORCE_PD_POWERDOWN		(1 << 14) | 
|  | #define   UTMIP_FORCE_PD2_POWERDOWN		(1 << 16) | 
|  | #define   UTMIP_FORCE_PDZI_POWERDOWN		(1 << 18) | 
|  | #define   UTMIP_XCVR_LSBIAS_SEL			(1 << 21) | 
|  | #define   UTMIP_XCVR_HSSLEW(x)			(((x) & 0x3) << 4) | 
|  | #define   UTMIP_XCVR_HSSLEW_MSB(x)		((((x) & 0x1fc) >> 2) << 25) | 
|  |  | 
|  | #define UTMIP_BIAS_CFG0		0x80c | 
|  | #define   UTMIP_OTGPD			(1 << 11) | 
|  | #define   UTMIP_BIASPD			(1 << 10) | 
|  | #define   UTMIP_HSSQUELCH_LEVEL(x)	(((x) & 0x3) << 0) | 
|  | #define   UTMIP_HSDISCON_LEVEL(x)	(((x) & 0x3) << 2) | 
|  | #define   UTMIP_HSDISCON_LEVEL_MSB(x)	((((x) & 0x4) >> 2) << 24) | 
|  |  | 
|  | #define UTMIP_HSRX_CFG0		0x810 | 
|  | #define   UTMIP_ELASTIC_LIMIT(x)	(((x) & 0x1f) << 10) | 
|  | #define   UTMIP_IDLE_WAIT(x)		(((x) & 0x1f) << 15) | 
|  |  | 
|  | #define UTMIP_HSRX_CFG1		0x814 | 
|  | #define   UTMIP_HS_SYNC_START_DLY(x)	(((x) & 0x1f) << 1) | 
|  |  | 
|  | #define UTMIP_TX_CFG0		0x820 | 
|  | #define   UTMIP_FS_PREABMLE_J		(1 << 19) | 
|  | #define   UTMIP_HS_DISCON_DISABLE	(1 << 8) | 
|  |  | 
|  | #define UTMIP_MISC_CFG0		0x824 | 
|  | #define   UTMIP_DPDM_OBSERVE		(1 << 26) | 
|  | #define   UTMIP_DPDM_OBSERVE_SEL(x)	(((x) & 0xf) << 27) | 
|  | #define   UTMIP_DPDM_OBSERVE_SEL_FS_J	UTMIP_DPDM_OBSERVE_SEL(0xf) | 
|  | #define   UTMIP_DPDM_OBSERVE_SEL_FS_K	UTMIP_DPDM_OBSERVE_SEL(0xe) | 
|  | #define   UTMIP_DPDM_OBSERVE_SEL_FS_SE1 UTMIP_DPDM_OBSERVE_SEL(0xd) | 
|  | #define   UTMIP_DPDM_OBSERVE_SEL_FS_SE0 UTMIP_DPDM_OBSERVE_SEL(0xc) | 
|  | #define   UTMIP_SUSPEND_EXIT_ON_EDGE	(1 << 22) | 
|  |  | 
|  | #define UTMIP_MISC_CFG1		0x828 | 
|  | #define   UTMIP_PLL_ACTIVE_DLY_COUNT(x)	(((x) & 0x1f) << 18) | 
|  | #define   UTMIP_PLLU_STABLE_COUNT(x)	(((x) & 0xfff) << 6) | 
|  |  | 
|  | #define UTMIP_DEBOUNCE_CFG0	0x82c | 
|  | #define   UTMIP_BIAS_DEBOUNCE_A(x)	(((x) & 0xffff) << 0) | 
|  |  | 
|  | #define UTMIP_BAT_CHRG_CFG0	0x830 | 
|  | #define   UTMIP_PD_CHRG			(1 << 0) | 
|  |  | 
|  | #define UTMIP_SPARE_CFG0	0x834 | 
|  | #define   FUSE_SETUP_SEL		(1 << 3) | 
|  |  | 
|  | #define UTMIP_XCVR_CFG1		0x838 | 
|  | #define   UTMIP_FORCE_PDDISC_POWERDOWN	(1 << 0) | 
|  | #define   UTMIP_FORCE_PDCHRP_POWERDOWN	(1 << 2) | 
|  | #define   UTMIP_FORCE_PDDR_POWERDOWN	(1 << 4) | 
|  | #define   UTMIP_XCVR_TERM_RANGE_ADJ(x)	(((x) & 0xf) << 18) | 
|  |  | 
|  | #define UTMIP_BIAS_CFG1		0x83c | 
|  | #define   UTMIP_BIAS_PDTRK_COUNT(x)	(((x) & 0x1f) << 3) | 
|  |  | 
|  | /* For Tegra30 and above only, the address is different in Tegra20 */ | 
|  | #define USB_USBMODE		0x1f8 | 
|  | #define   USB_USBMODE_MASK		(3 << 0) | 
|  | #define   USB_USBMODE_HOST		(3 << 0) | 
|  | #define   USB_USBMODE_DEVICE		(2 << 0) | 
|  |  | 
|  | static DEFINE_SPINLOCK(utmip_pad_lock); | 
|  | static int utmip_pad_count; | 
|  |  | 
|  | struct tegra_xtal_freq { | 
|  | int freq; | 
|  | u8 enable_delay; | 
|  | u8 stable_count; | 
|  | u8 active_delay; | 
|  | u8 xtal_freq_count; | 
|  | u16 debounce; | 
|  | }; | 
|  |  | 
|  | static const struct tegra_xtal_freq tegra_freq_table[] = { | 
|  | { | 
|  | .freq = 12000000, | 
|  | .enable_delay = 0x02, | 
|  | .stable_count = 0x2F, | 
|  | .active_delay = 0x04, | 
|  | .xtal_freq_count = 0x76, | 
|  | .debounce = 0x7530, | 
|  | }, | 
|  | { | 
|  | .freq = 13000000, | 
|  | .enable_delay = 0x02, | 
|  | .stable_count = 0x33, | 
|  | .active_delay = 0x05, | 
|  | .xtal_freq_count = 0x7F, | 
|  | .debounce = 0x7EF4, | 
|  | }, | 
|  | { | 
|  | .freq = 19200000, | 
|  | .enable_delay = 0x03, | 
|  | .stable_count = 0x4B, | 
|  | .active_delay = 0x06, | 
|  | .xtal_freq_count = 0xBB, | 
|  | .debounce = 0xBB80, | 
|  | }, | 
|  | { | 
|  | .freq = 26000000, | 
|  | .enable_delay = 0x04, | 
|  | .stable_count = 0x66, | 
|  | .active_delay = 0x09, | 
|  | .xtal_freq_count = 0xFE, | 
|  | .debounce = 0xFDE8, | 
|  | }, | 
|  | }; | 
|  |  | 
|  | static void set_pts(struct tegra_usb_phy *phy, u8 pts_val) | 
|  | { | 
|  | void __iomem *base = phy->regs; | 
|  | unsigned long val; | 
|  |  | 
|  | if (phy->soc_config->has_hostpc) { | 
|  | val = readl(base + TEGRA_USB_HOSTPC1_DEVLC); | 
|  | val &= ~TEGRA_USB_HOSTPC1_DEVLC_PTS(~0); | 
|  | val |= TEGRA_USB_HOSTPC1_DEVLC_PTS(pts_val); | 
|  | writel(val, base + TEGRA_USB_HOSTPC1_DEVLC); | 
|  | } else { | 
|  | val = readl(base + TEGRA_USB_PORTSC1) & ~TEGRA_PORTSC1_RWC_BITS; | 
|  | val &= ~TEGRA_USB_PORTSC1_PTS(~0); | 
|  | val |= TEGRA_USB_PORTSC1_PTS(pts_val); | 
|  | writel(val, base + TEGRA_USB_PORTSC1); | 
|  | } | 
|  | } | 
|  |  | 
|  | static void set_phcd(struct tegra_usb_phy *phy, bool enable) | 
|  | { | 
|  | void __iomem *base = phy->regs; | 
|  | unsigned long val; | 
|  |  | 
|  | if (phy->soc_config->has_hostpc) { | 
|  | val = readl(base + TEGRA_USB_HOSTPC1_DEVLC); | 
|  | if (enable) | 
|  | val |= TEGRA_USB_HOSTPC1_DEVLC_PHCD; | 
|  | else | 
|  | val &= ~TEGRA_USB_HOSTPC1_DEVLC_PHCD; | 
|  | writel(val, base + TEGRA_USB_HOSTPC1_DEVLC); | 
|  | } else { | 
|  | val = readl(base + TEGRA_USB_PORTSC1) & ~PORT_RWC_BITS; | 
|  | if (enable) | 
|  | val |= TEGRA_USB_PORTSC1_PHCD; | 
|  | else | 
|  | val &= ~TEGRA_USB_PORTSC1_PHCD; | 
|  | writel(val, base + TEGRA_USB_PORTSC1); | 
|  | } | 
|  | } | 
|  |  | 
|  | static int utmip_pad_open(struct tegra_usb_phy *phy) | 
|  | { | 
|  | int ret; | 
|  |  | 
|  | phy->pad_clk = devm_clk_get(phy->u_phy.dev, "utmi-pads"); | 
|  | if (IS_ERR(phy->pad_clk)) { | 
|  | ret = PTR_ERR(phy->pad_clk); | 
|  | dev_err(phy->u_phy.dev, | 
|  | "Failed to get UTMIP pad clock: %d\n", ret); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | phy->pad_rst = devm_reset_control_get_optional_shared( | 
|  | phy->u_phy.dev, "utmi-pads"); | 
|  | if (IS_ERR(phy->pad_rst)) { | 
|  | ret = PTR_ERR(phy->pad_rst); | 
|  | dev_err(phy->u_phy.dev, | 
|  | "Failed to get UTMI-pads reset: %d\n", ret); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | ret = clk_prepare_enable(phy->pad_clk); | 
|  | if (ret) { | 
|  | dev_err(phy->u_phy.dev, | 
|  | "Failed to enable UTMI-pads clock: %d\n", ret); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | spin_lock(&utmip_pad_lock); | 
|  |  | 
|  | ret = reset_control_deassert(phy->pad_rst); | 
|  | if (ret) { | 
|  | dev_err(phy->u_phy.dev, | 
|  | "Failed to initialize UTMI-pads reset: %d\n", ret); | 
|  | goto unlock; | 
|  | } | 
|  |  | 
|  | ret = reset_control_assert(phy->pad_rst); | 
|  | if (ret) { | 
|  | dev_err(phy->u_phy.dev, | 
|  | "Failed to assert UTMI-pads reset: %d\n", ret); | 
|  | goto unlock; | 
|  | } | 
|  |  | 
|  | udelay(1); | 
|  |  | 
|  | ret = reset_control_deassert(phy->pad_rst); | 
|  | if (ret) | 
|  | dev_err(phy->u_phy.dev, | 
|  | "Failed to deassert UTMI-pads reset: %d\n", ret); | 
|  | unlock: | 
|  | spin_unlock(&utmip_pad_lock); | 
|  |  | 
|  | clk_disable_unprepare(phy->pad_clk); | 
|  |  | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static int utmip_pad_close(struct tegra_usb_phy *phy) | 
|  | { | 
|  | int ret; | 
|  |  | 
|  | ret = clk_prepare_enable(phy->pad_clk); | 
|  | if (ret) { | 
|  | dev_err(phy->u_phy.dev, | 
|  | "Failed to enable UTMI-pads clock: %d\n", ret); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | ret = reset_control_assert(phy->pad_rst); | 
|  | if (ret) | 
|  | dev_err(phy->u_phy.dev, | 
|  | "Failed to assert UTMI-pads reset: %d\n", ret); | 
|  |  | 
|  | udelay(1); | 
|  |  | 
|  | clk_disable_unprepare(phy->pad_clk); | 
|  |  | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static void utmip_pad_power_on(struct tegra_usb_phy *phy) | 
|  | { | 
|  | unsigned long val, flags; | 
|  | void __iomem *base = phy->pad_regs; | 
|  | struct tegra_utmip_config *config = phy->config; | 
|  |  | 
|  | clk_prepare_enable(phy->pad_clk); | 
|  |  | 
|  | spin_lock_irqsave(&utmip_pad_lock, flags); | 
|  |  | 
|  | if (utmip_pad_count++ == 0) { | 
|  | val = readl(base + UTMIP_BIAS_CFG0); | 
|  | val &= ~(UTMIP_OTGPD | UTMIP_BIASPD); | 
|  |  | 
|  | if (phy->soc_config->requires_extra_tuning_parameters) { | 
|  | val &= ~(UTMIP_HSSQUELCH_LEVEL(~0) | | 
|  | UTMIP_HSDISCON_LEVEL(~0) | | 
|  | UTMIP_HSDISCON_LEVEL_MSB(~0)); | 
|  |  | 
|  | val |= UTMIP_HSSQUELCH_LEVEL(config->hssquelch_level); | 
|  | val |= UTMIP_HSDISCON_LEVEL(config->hsdiscon_level); | 
|  | val |= UTMIP_HSDISCON_LEVEL_MSB(config->hsdiscon_level); | 
|  | } | 
|  | writel(val, base + UTMIP_BIAS_CFG0); | 
|  | } | 
|  |  | 
|  | spin_unlock_irqrestore(&utmip_pad_lock, flags); | 
|  |  | 
|  | clk_disable_unprepare(phy->pad_clk); | 
|  | } | 
|  |  | 
|  | static int utmip_pad_power_off(struct tegra_usb_phy *phy) | 
|  | { | 
|  | unsigned long val, flags; | 
|  | void __iomem *base = phy->pad_regs; | 
|  |  | 
|  | if (!utmip_pad_count) { | 
|  | dev_err(phy->u_phy.dev, "UTMIP pad already powered off\n"); | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | clk_prepare_enable(phy->pad_clk); | 
|  |  | 
|  | spin_lock_irqsave(&utmip_pad_lock, flags); | 
|  |  | 
|  | if (--utmip_pad_count == 0) { | 
|  | val = readl(base + UTMIP_BIAS_CFG0); | 
|  | val |= UTMIP_OTGPD | UTMIP_BIASPD; | 
|  | writel(val, base + UTMIP_BIAS_CFG0); | 
|  | } | 
|  |  | 
|  | spin_unlock_irqrestore(&utmip_pad_lock, flags); | 
|  |  | 
|  | clk_disable_unprepare(phy->pad_clk); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int utmi_wait_register(void __iomem *reg, u32 mask, u32 result) | 
|  | { | 
|  | u32 tmp; | 
|  |  | 
|  | return readl_poll_timeout(reg, tmp, (tmp & mask) == result, | 
|  | 2000, 6000); | 
|  | } | 
|  |  | 
|  | static void utmi_phy_clk_disable(struct tegra_usb_phy *phy) | 
|  | { | 
|  | unsigned long val; | 
|  | void __iomem *base = phy->regs; | 
|  |  | 
|  | /* | 
|  | * The USB driver may have already initiated the phy clock | 
|  | * disable so wait to see if the clock turns off and if not | 
|  | * then proceed with gating the clock. | 
|  | */ | 
|  | if (utmi_wait_register(base + USB_SUSP_CTRL, USB_PHY_CLK_VALID, 0) == 0) | 
|  | return; | 
|  |  | 
|  | if (phy->is_legacy_phy) { | 
|  | val = readl(base + USB_SUSP_CTRL); | 
|  | val |= USB_SUSP_SET; | 
|  | writel(val, base + USB_SUSP_CTRL); | 
|  |  | 
|  | udelay(10); | 
|  |  | 
|  | val = readl(base + USB_SUSP_CTRL); | 
|  | val &= ~USB_SUSP_SET; | 
|  | writel(val, base + USB_SUSP_CTRL); | 
|  | } else | 
|  | set_phcd(phy, true); | 
|  |  | 
|  | if (utmi_wait_register(base + USB_SUSP_CTRL, USB_PHY_CLK_VALID, 0) < 0) | 
|  | dev_err(phy->u_phy.dev, | 
|  | "Timeout waiting for PHY to stabilize on disable\n"); | 
|  | } | 
|  |  | 
|  | static void utmi_phy_clk_enable(struct tegra_usb_phy *phy) | 
|  | { | 
|  | unsigned long val; | 
|  | void __iomem *base = phy->regs; | 
|  |  | 
|  | /* | 
|  | * The USB driver may have already initiated the phy clock | 
|  | * enable so wait to see if the clock turns on and if not | 
|  | * then proceed with ungating the clock. | 
|  | */ | 
|  | if (utmi_wait_register(base + USB_SUSP_CTRL, USB_PHY_CLK_VALID, | 
|  | USB_PHY_CLK_VALID) == 0) | 
|  | return; | 
|  |  | 
|  | if (phy->is_legacy_phy) { | 
|  | val = readl(base + USB_SUSP_CTRL); | 
|  | val |= USB_SUSP_CLR; | 
|  | writel(val, base + USB_SUSP_CTRL); | 
|  |  | 
|  | udelay(10); | 
|  |  | 
|  | val = readl(base + USB_SUSP_CTRL); | 
|  | val &= ~USB_SUSP_CLR; | 
|  | writel(val, base + USB_SUSP_CTRL); | 
|  | } else | 
|  | set_phcd(phy, false); | 
|  |  | 
|  | if (utmi_wait_register(base + USB_SUSP_CTRL, USB_PHY_CLK_VALID, | 
|  | USB_PHY_CLK_VALID)) | 
|  | dev_err(phy->u_phy.dev, | 
|  | "Timeout waiting for PHY to stabilize on enable\n"); | 
|  | } | 
|  |  | 
|  | static int utmi_phy_power_on(struct tegra_usb_phy *phy) | 
|  | { | 
|  | unsigned long val; | 
|  | void __iomem *base = phy->regs; | 
|  | struct tegra_utmip_config *config = phy->config; | 
|  |  | 
|  | val = readl(base + USB_SUSP_CTRL); | 
|  | val |= UTMIP_RESET; | 
|  | writel(val, base + USB_SUSP_CTRL); | 
|  |  | 
|  | if (phy->is_legacy_phy) { | 
|  | val = readl(base + USB1_LEGACY_CTRL); | 
|  | val |= USB1_NO_LEGACY_MODE; | 
|  | writel(val, base + USB1_LEGACY_CTRL); | 
|  | } | 
|  |  | 
|  | val = readl(base + UTMIP_TX_CFG0); | 
|  | val |= UTMIP_FS_PREABMLE_J; | 
|  | writel(val, base + UTMIP_TX_CFG0); | 
|  |  | 
|  | val = readl(base + UTMIP_HSRX_CFG0); | 
|  | val &= ~(UTMIP_IDLE_WAIT(~0) | UTMIP_ELASTIC_LIMIT(~0)); | 
|  | val |= UTMIP_IDLE_WAIT(config->idle_wait_delay); | 
|  | val |= UTMIP_ELASTIC_LIMIT(config->elastic_limit); | 
|  | writel(val, base + UTMIP_HSRX_CFG0); | 
|  |  | 
|  | val = readl(base + UTMIP_HSRX_CFG1); | 
|  | val &= ~UTMIP_HS_SYNC_START_DLY(~0); | 
|  | val |= UTMIP_HS_SYNC_START_DLY(config->hssync_start_delay); | 
|  | writel(val, base + UTMIP_HSRX_CFG1); | 
|  |  | 
|  | val = readl(base + UTMIP_DEBOUNCE_CFG0); | 
|  | val &= ~UTMIP_BIAS_DEBOUNCE_A(~0); | 
|  | val |= UTMIP_BIAS_DEBOUNCE_A(phy->freq->debounce); | 
|  | writel(val, base + UTMIP_DEBOUNCE_CFG0); | 
|  |  | 
|  | val = readl(base + UTMIP_MISC_CFG0); | 
|  | val &= ~UTMIP_SUSPEND_EXIT_ON_EDGE; | 
|  | writel(val, base + UTMIP_MISC_CFG0); | 
|  |  | 
|  | if (!phy->soc_config->utmi_pll_config_in_car_module) { | 
|  | val = readl(base + UTMIP_MISC_CFG1); | 
|  | val &= ~(UTMIP_PLL_ACTIVE_DLY_COUNT(~0) | | 
|  | UTMIP_PLLU_STABLE_COUNT(~0)); | 
|  | val |= UTMIP_PLL_ACTIVE_DLY_COUNT(phy->freq->active_delay) | | 
|  | UTMIP_PLLU_STABLE_COUNT(phy->freq->stable_count); | 
|  | writel(val, base + UTMIP_MISC_CFG1); | 
|  |  | 
|  | val = readl(base + UTMIP_PLL_CFG1); | 
|  | val &= ~(UTMIP_XTAL_FREQ_COUNT(~0) | | 
|  | UTMIP_PLLU_ENABLE_DLY_COUNT(~0)); | 
|  | val |= UTMIP_XTAL_FREQ_COUNT(phy->freq->xtal_freq_count) | | 
|  | UTMIP_PLLU_ENABLE_DLY_COUNT(phy->freq->enable_delay); | 
|  | writel(val, base + UTMIP_PLL_CFG1); | 
|  | } | 
|  |  | 
|  | if (phy->mode == USB_DR_MODE_PERIPHERAL) { | 
|  | val = readl(base + USB_SUSP_CTRL); | 
|  | val &= ~(USB_WAKE_ON_CNNT_EN_DEV | USB_WAKE_ON_DISCON_EN_DEV); | 
|  | writel(val, base + USB_SUSP_CTRL); | 
|  |  | 
|  | val = readl(base + UTMIP_BAT_CHRG_CFG0); | 
|  | val &= ~UTMIP_PD_CHRG; | 
|  | writel(val, base + UTMIP_BAT_CHRG_CFG0); | 
|  | } else { | 
|  | val = readl(base + UTMIP_BAT_CHRG_CFG0); | 
|  | val |= UTMIP_PD_CHRG; | 
|  | writel(val, base + UTMIP_BAT_CHRG_CFG0); | 
|  | } | 
|  |  | 
|  | utmip_pad_power_on(phy); | 
|  |  | 
|  | val = readl(base + UTMIP_XCVR_CFG0); | 
|  | val &= ~(UTMIP_FORCE_PD_POWERDOWN | UTMIP_FORCE_PD2_POWERDOWN | | 
|  | UTMIP_FORCE_PDZI_POWERDOWN | UTMIP_XCVR_LSBIAS_SEL | | 
|  | UTMIP_XCVR_SETUP(~0) | UTMIP_XCVR_SETUP_MSB(~0) | | 
|  | UTMIP_XCVR_LSFSLEW(~0) | UTMIP_XCVR_LSRSLEW(~0)); | 
|  |  | 
|  | if (!config->xcvr_setup_use_fuses) { | 
|  | val |= UTMIP_XCVR_SETUP(config->xcvr_setup); | 
|  | val |= UTMIP_XCVR_SETUP_MSB(config->xcvr_setup); | 
|  | } | 
|  | val |= UTMIP_XCVR_LSFSLEW(config->xcvr_lsfslew); | 
|  | val |= UTMIP_XCVR_LSRSLEW(config->xcvr_lsrslew); | 
|  |  | 
|  | if (phy->soc_config->requires_extra_tuning_parameters) { | 
|  | val &= ~(UTMIP_XCVR_HSSLEW(~0) | UTMIP_XCVR_HSSLEW_MSB(~0)); | 
|  | val |= UTMIP_XCVR_HSSLEW(config->xcvr_hsslew); | 
|  | val |= UTMIP_XCVR_HSSLEW_MSB(config->xcvr_hsslew); | 
|  | } | 
|  | writel(val, base + UTMIP_XCVR_CFG0); | 
|  |  | 
|  | val = readl(base + UTMIP_XCVR_CFG1); | 
|  | val &= ~(UTMIP_FORCE_PDDISC_POWERDOWN | UTMIP_FORCE_PDCHRP_POWERDOWN | | 
|  | UTMIP_FORCE_PDDR_POWERDOWN | UTMIP_XCVR_TERM_RANGE_ADJ(~0)); | 
|  | val |= UTMIP_XCVR_TERM_RANGE_ADJ(config->term_range_adj); | 
|  | writel(val, base + UTMIP_XCVR_CFG1); | 
|  |  | 
|  | val = readl(base + UTMIP_BIAS_CFG1); | 
|  | val &= ~UTMIP_BIAS_PDTRK_COUNT(~0); | 
|  | val |= UTMIP_BIAS_PDTRK_COUNT(0x5); | 
|  | writel(val, base + UTMIP_BIAS_CFG1); | 
|  |  | 
|  | val = readl(base + UTMIP_SPARE_CFG0); | 
|  | if (config->xcvr_setup_use_fuses) | 
|  | val |= FUSE_SETUP_SEL; | 
|  | else | 
|  | val &= ~FUSE_SETUP_SEL; | 
|  | writel(val, base + UTMIP_SPARE_CFG0); | 
|  |  | 
|  | if (!phy->is_legacy_phy) { | 
|  | val = readl(base + USB_SUSP_CTRL); | 
|  | val |= UTMIP_PHY_ENABLE; | 
|  | writel(val, base + USB_SUSP_CTRL); | 
|  | } | 
|  |  | 
|  | val = readl(base + USB_SUSP_CTRL); | 
|  | val &= ~UTMIP_RESET; | 
|  | writel(val, base + USB_SUSP_CTRL); | 
|  |  | 
|  | if (phy->is_legacy_phy) { | 
|  | val = readl(base + USB1_LEGACY_CTRL); | 
|  | val &= ~USB1_VBUS_SENSE_CTL_MASK; | 
|  | val |= USB1_VBUS_SENSE_CTL_A_SESS_VLD; | 
|  | writel(val, base + USB1_LEGACY_CTRL); | 
|  |  | 
|  | val = readl(base + USB_SUSP_CTRL); | 
|  | val &= ~USB_SUSP_SET; | 
|  | writel(val, base + USB_SUSP_CTRL); | 
|  | } | 
|  |  | 
|  | utmi_phy_clk_enable(phy); | 
|  |  | 
|  | if (phy->soc_config->requires_usbmode_setup) { | 
|  | val = readl(base + USB_USBMODE); | 
|  | val &= ~USB_USBMODE_MASK; | 
|  | if (phy->mode == USB_DR_MODE_HOST) | 
|  | val |= USB_USBMODE_HOST; | 
|  | else | 
|  | val |= USB_USBMODE_DEVICE; | 
|  | writel(val, base + USB_USBMODE); | 
|  | } | 
|  |  | 
|  | if (!phy->is_legacy_phy) | 
|  | set_pts(phy, 0); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int utmi_phy_power_off(struct tegra_usb_phy *phy) | 
|  | { | 
|  | unsigned long val; | 
|  | void __iomem *base = phy->regs; | 
|  |  | 
|  | utmi_phy_clk_disable(phy); | 
|  |  | 
|  | if (phy->mode == USB_DR_MODE_PERIPHERAL) { | 
|  | val = readl(base + USB_SUSP_CTRL); | 
|  | val &= ~USB_WAKEUP_DEBOUNCE_COUNT(~0); | 
|  | val |= USB_WAKE_ON_CNNT_EN_DEV | USB_WAKEUP_DEBOUNCE_COUNT(5); | 
|  | writel(val, base + USB_SUSP_CTRL); | 
|  | } | 
|  |  | 
|  | val = readl(base + USB_SUSP_CTRL); | 
|  | val |= UTMIP_RESET; | 
|  | writel(val, base + USB_SUSP_CTRL); | 
|  |  | 
|  | val = readl(base + UTMIP_BAT_CHRG_CFG0); | 
|  | val |= UTMIP_PD_CHRG; | 
|  | writel(val, base + UTMIP_BAT_CHRG_CFG0); | 
|  |  | 
|  | val = readl(base + UTMIP_XCVR_CFG0); | 
|  | val |= UTMIP_FORCE_PD_POWERDOWN | UTMIP_FORCE_PD2_POWERDOWN | | 
|  | UTMIP_FORCE_PDZI_POWERDOWN; | 
|  | writel(val, base + UTMIP_XCVR_CFG0); | 
|  |  | 
|  | val = readl(base + UTMIP_XCVR_CFG1); | 
|  | val |= UTMIP_FORCE_PDDISC_POWERDOWN | UTMIP_FORCE_PDCHRP_POWERDOWN | | 
|  | UTMIP_FORCE_PDDR_POWERDOWN; | 
|  | writel(val, base + UTMIP_XCVR_CFG1); | 
|  |  | 
|  | return utmip_pad_power_off(phy); | 
|  | } | 
|  |  | 
|  | static void utmi_phy_preresume(struct tegra_usb_phy *phy) | 
|  | { | 
|  | unsigned long val; | 
|  | void __iomem *base = phy->regs; | 
|  |  | 
|  | val = readl(base + UTMIP_TX_CFG0); | 
|  | val |= UTMIP_HS_DISCON_DISABLE; | 
|  | writel(val, base + UTMIP_TX_CFG0); | 
|  | } | 
|  |  | 
|  | static void utmi_phy_postresume(struct tegra_usb_phy *phy) | 
|  | { | 
|  | unsigned long val; | 
|  | void __iomem *base = phy->regs; | 
|  |  | 
|  | val = readl(base + UTMIP_TX_CFG0); | 
|  | val &= ~UTMIP_HS_DISCON_DISABLE; | 
|  | writel(val, base + UTMIP_TX_CFG0); | 
|  | } | 
|  |  | 
|  | static void utmi_phy_restore_start(struct tegra_usb_phy *phy, | 
|  | enum tegra_usb_phy_port_speed port_speed) | 
|  | { | 
|  | unsigned long val; | 
|  | void __iomem *base = phy->regs; | 
|  |  | 
|  | val = readl(base + UTMIP_MISC_CFG0); | 
|  | val &= ~UTMIP_DPDM_OBSERVE_SEL(~0); | 
|  | if (port_speed == TEGRA_USB_PHY_PORT_SPEED_LOW) | 
|  | val |= UTMIP_DPDM_OBSERVE_SEL_FS_K; | 
|  | else | 
|  | val |= UTMIP_DPDM_OBSERVE_SEL_FS_J; | 
|  | writel(val, base + UTMIP_MISC_CFG0); | 
|  | udelay(1); | 
|  |  | 
|  | val = readl(base + UTMIP_MISC_CFG0); | 
|  | val |= UTMIP_DPDM_OBSERVE; | 
|  | writel(val, base + UTMIP_MISC_CFG0); | 
|  | udelay(10); | 
|  | } | 
|  |  | 
|  | static void utmi_phy_restore_end(struct tegra_usb_phy *phy) | 
|  | { | 
|  | unsigned long val; | 
|  | void __iomem *base = phy->regs; | 
|  |  | 
|  | val = readl(base + UTMIP_MISC_CFG0); | 
|  | val &= ~UTMIP_DPDM_OBSERVE; | 
|  | writel(val, base + UTMIP_MISC_CFG0); | 
|  | udelay(10); | 
|  | } | 
|  |  | 
|  | static int ulpi_phy_power_on(struct tegra_usb_phy *phy) | 
|  | { | 
|  | int ret; | 
|  | unsigned long val; | 
|  | void __iomem *base = phy->regs; | 
|  |  | 
|  | ret = gpio_direction_output(phy->reset_gpio, 0); | 
|  | if (ret < 0) { | 
|  | dev_err(phy->u_phy.dev, "GPIO %d not set to 0: %d\n", | 
|  | phy->reset_gpio, ret); | 
|  | return ret; | 
|  | } | 
|  | msleep(5); | 
|  | ret = gpio_direction_output(phy->reset_gpio, 1); | 
|  | if (ret < 0) { | 
|  | dev_err(phy->u_phy.dev, "GPIO %d not set to 1: %d\n", | 
|  | phy->reset_gpio, ret); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | clk_prepare_enable(phy->clk); | 
|  | msleep(1); | 
|  |  | 
|  | val = readl(base + USB_SUSP_CTRL); | 
|  | val |= UHSIC_RESET; | 
|  | writel(val, base + USB_SUSP_CTRL); | 
|  |  | 
|  | val = readl(base + ULPI_TIMING_CTRL_0); | 
|  | val |= ULPI_OUTPUT_PINMUX_BYP | ULPI_CLKOUT_PINMUX_BYP; | 
|  | writel(val, base + ULPI_TIMING_CTRL_0); | 
|  |  | 
|  | val = readl(base + USB_SUSP_CTRL); | 
|  | val |= ULPI_PHY_ENABLE; | 
|  | writel(val, base + USB_SUSP_CTRL); | 
|  |  | 
|  | val = 0; | 
|  | writel(val, base + ULPI_TIMING_CTRL_1); | 
|  |  | 
|  | val |= ULPI_DATA_TRIMMER_SEL(4); | 
|  | val |= ULPI_STPDIRNXT_TRIMMER_SEL(4); | 
|  | val |= ULPI_DIR_TRIMMER_SEL(4); | 
|  | writel(val, base + ULPI_TIMING_CTRL_1); | 
|  | udelay(10); | 
|  |  | 
|  | val |= ULPI_DATA_TRIMMER_LOAD; | 
|  | val |= ULPI_STPDIRNXT_TRIMMER_LOAD; | 
|  | val |= ULPI_DIR_TRIMMER_LOAD; | 
|  | writel(val, base + ULPI_TIMING_CTRL_1); | 
|  |  | 
|  | /* Fix VbusInvalid due to floating VBUS */ | 
|  | ret = usb_phy_io_write(phy->ulpi, 0x40, 0x08); | 
|  | if (ret) { | 
|  | dev_err(phy->u_phy.dev, "ULPI write failed: %d\n", ret); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | ret = usb_phy_io_write(phy->ulpi, 0x80, 0x0B); | 
|  | if (ret) { | 
|  | dev_err(phy->u_phy.dev, "ULPI write failed: %d\n", ret); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | val = readl(base + USB_SUSP_CTRL); | 
|  | val |= USB_SUSP_CLR; | 
|  | writel(val, base + USB_SUSP_CTRL); | 
|  | udelay(100); | 
|  |  | 
|  | val = readl(base + USB_SUSP_CTRL); | 
|  | val &= ~USB_SUSP_CLR; | 
|  | writel(val, base + USB_SUSP_CTRL); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int ulpi_phy_power_off(struct tegra_usb_phy *phy) | 
|  | { | 
|  | clk_disable(phy->clk); | 
|  | return gpio_direction_output(phy->reset_gpio, 0); | 
|  | } | 
|  |  | 
|  | static void tegra_usb_phy_close(struct tegra_usb_phy *phy) | 
|  | { | 
|  | if (!IS_ERR(phy->vbus)) | 
|  | regulator_disable(phy->vbus); | 
|  |  | 
|  | if (!phy->is_ulpi_phy) | 
|  | utmip_pad_close(phy); | 
|  |  | 
|  | clk_disable_unprepare(phy->pll_u); | 
|  | } | 
|  |  | 
|  | static int tegra_usb_phy_power_on(struct tegra_usb_phy *phy) | 
|  | { | 
|  | if (phy->is_ulpi_phy) | 
|  | return ulpi_phy_power_on(phy); | 
|  | else | 
|  | return utmi_phy_power_on(phy); | 
|  | } | 
|  |  | 
|  | static int tegra_usb_phy_power_off(struct tegra_usb_phy *phy) | 
|  | { | 
|  | if (phy->is_ulpi_phy) | 
|  | return ulpi_phy_power_off(phy); | 
|  | else | 
|  | return utmi_phy_power_off(phy); | 
|  | } | 
|  |  | 
|  | static int	tegra_usb_phy_suspend(struct usb_phy *x, int suspend) | 
|  | { | 
|  | struct tegra_usb_phy *phy = container_of(x, struct tegra_usb_phy, u_phy); | 
|  | if (suspend) | 
|  | return tegra_usb_phy_power_off(phy); | 
|  | else | 
|  | return tegra_usb_phy_power_on(phy); | 
|  | } | 
|  |  | 
|  | static int ulpi_open(struct tegra_usb_phy *phy) | 
|  | { | 
|  | int err; | 
|  |  | 
|  | phy->clk = devm_clk_get(phy->u_phy.dev, "ulpi-link"); | 
|  | if (IS_ERR(phy->clk)) { | 
|  | err = PTR_ERR(phy->clk); | 
|  | dev_err(phy->u_phy.dev, "Failed to get ULPI clock: %d\n", err); | 
|  | return err; | 
|  | } | 
|  |  | 
|  | err = devm_gpio_request(phy->u_phy.dev, phy->reset_gpio, | 
|  | "ulpi_phy_reset_b"); | 
|  | if (err < 0) { | 
|  | dev_err(phy->u_phy.dev, "Request failed for GPIO %d: %d\n", | 
|  | phy->reset_gpio, err); | 
|  | return err; | 
|  | } | 
|  |  | 
|  | err = gpio_direction_output(phy->reset_gpio, 0); | 
|  | if (err < 0) { | 
|  | dev_err(phy->u_phy.dev, | 
|  | "GPIO %d direction not set to output: %d\n", | 
|  | phy->reset_gpio, err); | 
|  | return err; | 
|  | } | 
|  |  | 
|  | phy->ulpi = otg_ulpi_create(&ulpi_viewport_access_ops, 0); | 
|  | if (!phy->ulpi) { | 
|  | dev_err(phy->u_phy.dev, "Failed to create ULPI OTG\n"); | 
|  | err = -ENOMEM; | 
|  | return err; | 
|  | } | 
|  |  | 
|  | phy->ulpi->io_priv = phy->regs + ULPI_VIEWPORT; | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int tegra_usb_phy_init(struct tegra_usb_phy *phy) | 
|  | { | 
|  | unsigned long parent_rate; | 
|  | int i; | 
|  | int err; | 
|  |  | 
|  | phy->pll_u = devm_clk_get(phy->u_phy.dev, "pll_u"); | 
|  | if (IS_ERR(phy->pll_u)) { | 
|  | err = PTR_ERR(phy->pll_u); | 
|  | dev_err(phy->u_phy.dev, | 
|  | "Failed to get pll_u clock: %d\n", err); | 
|  | return err; | 
|  | } | 
|  |  | 
|  | err = clk_prepare_enable(phy->pll_u); | 
|  | if (err) | 
|  | return err; | 
|  |  | 
|  | parent_rate = clk_get_rate(clk_get_parent(phy->pll_u)); | 
|  | for (i = 0; i < ARRAY_SIZE(tegra_freq_table); i++) { | 
|  | if (tegra_freq_table[i].freq == parent_rate) { | 
|  | phy->freq = &tegra_freq_table[i]; | 
|  | break; | 
|  | } | 
|  | } | 
|  | if (!phy->freq) { | 
|  | dev_err(phy->u_phy.dev, "Invalid pll_u parent rate %ld\n", | 
|  | parent_rate); | 
|  | err = -EINVAL; | 
|  | goto fail; | 
|  | } | 
|  |  | 
|  | if (!IS_ERR(phy->vbus)) { | 
|  | err = regulator_enable(phy->vbus); | 
|  | if (err) { | 
|  | dev_err(phy->u_phy.dev, | 
|  | "Failed to enable USB VBUS regulator: %d\n", | 
|  | err); | 
|  | goto fail; | 
|  | } | 
|  | } | 
|  |  | 
|  | if (phy->is_ulpi_phy) | 
|  | err = ulpi_open(phy); | 
|  | else | 
|  | err = utmip_pad_open(phy); | 
|  | if (err < 0) | 
|  | goto fail; | 
|  |  | 
|  | return 0; | 
|  |  | 
|  | fail: | 
|  | clk_disable_unprepare(phy->pll_u); | 
|  | return err; | 
|  | } | 
|  |  | 
|  | void tegra_usb_phy_preresume(struct usb_phy *x) | 
|  | { | 
|  | struct tegra_usb_phy *phy = container_of(x, struct tegra_usb_phy, u_phy); | 
|  |  | 
|  | if (!phy->is_ulpi_phy) | 
|  | utmi_phy_preresume(phy); | 
|  | } | 
|  | EXPORT_SYMBOL_GPL(tegra_usb_phy_preresume); | 
|  |  | 
|  | void tegra_usb_phy_postresume(struct usb_phy *x) | 
|  | { | 
|  | struct tegra_usb_phy *phy = container_of(x, struct tegra_usb_phy, u_phy); | 
|  |  | 
|  | if (!phy->is_ulpi_phy) | 
|  | utmi_phy_postresume(phy); | 
|  | } | 
|  | EXPORT_SYMBOL_GPL(tegra_usb_phy_postresume); | 
|  |  | 
|  | void tegra_ehci_phy_restore_start(struct usb_phy *x, | 
|  | enum tegra_usb_phy_port_speed port_speed) | 
|  | { | 
|  | struct tegra_usb_phy *phy = container_of(x, struct tegra_usb_phy, u_phy); | 
|  |  | 
|  | if (!phy->is_ulpi_phy) | 
|  | utmi_phy_restore_start(phy, port_speed); | 
|  | } | 
|  | EXPORT_SYMBOL_GPL(tegra_ehci_phy_restore_start); | 
|  |  | 
|  | void tegra_ehci_phy_restore_end(struct usb_phy *x) | 
|  | { | 
|  | struct tegra_usb_phy *phy = container_of(x, struct tegra_usb_phy, u_phy); | 
|  |  | 
|  | if (!phy->is_ulpi_phy) | 
|  | utmi_phy_restore_end(phy); | 
|  | } | 
|  | EXPORT_SYMBOL_GPL(tegra_ehci_phy_restore_end); | 
|  |  | 
|  | static int read_utmi_param(struct platform_device *pdev, const char *param, | 
|  | u8 *dest) | 
|  | { | 
|  | u32 value; | 
|  | int err = of_property_read_u32(pdev->dev.of_node, param, &value); | 
|  | *dest = (u8)value; | 
|  | if (err < 0) | 
|  | dev_err(&pdev->dev, | 
|  | "Failed to read USB UTMI parameter %s: %d\n", | 
|  | param, err); | 
|  | return err; | 
|  | } | 
|  |  | 
|  | static int utmi_phy_probe(struct tegra_usb_phy *tegra_phy, | 
|  | struct platform_device *pdev) | 
|  | { | 
|  | struct resource *res; | 
|  | int err; | 
|  | struct tegra_utmip_config *config; | 
|  |  | 
|  | tegra_phy->is_ulpi_phy = false; | 
|  |  | 
|  | res = platform_get_resource(pdev, IORESOURCE_MEM, 1); | 
|  | if (!res) { | 
|  | dev_err(&pdev->dev, "Failed to get UTMI pad regs\n"); | 
|  | return  -ENXIO; | 
|  | } | 
|  |  | 
|  | tegra_phy->pad_regs = devm_ioremap(&pdev->dev, res->start, | 
|  | resource_size(res)); | 
|  | if (!tegra_phy->pad_regs) { | 
|  | dev_err(&pdev->dev, "Failed to remap UTMI pad regs\n"); | 
|  | return -ENOMEM; | 
|  | } | 
|  |  | 
|  | tegra_phy->config = devm_kzalloc(&pdev->dev, sizeof(*config), | 
|  | GFP_KERNEL); | 
|  | if (!tegra_phy->config) | 
|  | return -ENOMEM; | 
|  |  | 
|  | config = tegra_phy->config; | 
|  |  | 
|  | err = read_utmi_param(pdev, "nvidia,hssync-start-delay", | 
|  | &config->hssync_start_delay); | 
|  | if (err < 0) | 
|  | return err; | 
|  |  | 
|  | err = read_utmi_param(pdev, "nvidia,elastic-limit", | 
|  | &config->elastic_limit); | 
|  | if (err < 0) | 
|  | return err; | 
|  |  | 
|  | err = read_utmi_param(pdev, "nvidia,idle-wait-delay", | 
|  | &config->idle_wait_delay); | 
|  | if (err < 0) | 
|  | return err; | 
|  |  | 
|  | err = read_utmi_param(pdev, "nvidia,term-range-adj", | 
|  | &config->term_range_adj); | 
|  | if (err < 0) | 
|  | return err; | 
|  |  | 
|  | err = read_utmi_param(pdev, "nvidia,xcvr-lsfslew", | 
|  | &config->xcvr_lsfslew); | 
|  | if (err < 0) | 
|  | return err; | 
|  |  | 
|  | err = read_utmi_param(pdev, "nvidia,xcvr-lsrslew", | 
|  | &config->xcvr_lsrslew); | 
|  | if (err < 0) | 
|  | return err; | 
|  |  | 
|  | if (tegra_phy->soc_config->requires_extra_tuning_parameters) { | 
|  | err = read_utmi_param(pdev, "nvidia,xcvr-hsslew", | 
|  | &config->xcvr_hsslew); | 
|  | if (err < 0) | 
|  | return err; | 
|  |  | 
|  | err = read_utmi_param(pdev, "nvidia,hssquelch-level", | 
|  | &config->hssquelch_level); | 
|  | if (err < 0) | 
|  | return err; | 
|  |  | 
|  | err = read_utmi_param(pdev, "nvidia,hsdiscon-level", | 
|  | &config->hsdiscon_level); | 
|  | if (err < 0) | 
|  | return err; | 
|  | } | 
|  |  | 
|  | config->xcvr_setup_use_fuses = of_property_read_bool( | 
|  | pdev->dev.of_node, "nvidia,xcvr-setup-use-fuses"); | 
|  |  | 
|  | if (!config->xcvr_setup_use_fuses) { | 
|  | err = read_utmi_param(pdev, "nvidia,xcvr-setup", | 
|  | &config->xcvr_setup); | 
|  | if (err < 0) | 
|  | return err; | 
|  | } | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static const struct tegra_phy_soc_config tegra20_soc_config = { | 
|  | .utmi_pll_config_in_car_module = false, | 
|  | .has_hostpc = false, | 
|  | .requires_usbmode_setup = false, | 
|  | .requires_extra_tuning_parameters = false, | 
|  | }; | 
|  |  | 
|  | static const struct tegra_phy_soc_config tegra30_soc_config = { | 
|  | .utmi_pll_config_in_car_module = true, | 
|  | .has_hostpc = true, | 
|  | .requires_usbmode_setup = true, | 
|  | .requires_extra_tuning_parameters = true, | 
|  | }; | 
|  |  | 
|  | static const struct of_device_id tegra_usb_phy_id_table[] = { | 
|  | { .compatible = "nvidia,tegra30-usb-phy", .data = &tegra30_soc_config }, | 
|  | { .compatible = "nvidia,tegra20-usb-phy", .data = &tegra20_soc_config }, | 
|  | { }, | 
|  | }; | 
|  | MODULE_DEVICE_TABLE(of, tegra_usb_phy_id_table); | 
|  |  | 
|  | static int tegra_usb_phy_probe(struct platform_device *pdev) | 
|  | { | 
|  | const struct of_device_id *match; | 
|  | struct resource *res; | 
|  | struct tegra_usb_phy *tegra_phy = NULL; | 
|  | struct device_node *np = pdev->dev.of_node; | 
|  | enum usb_phy_interface phy_type; | 
|  | int err; | 
|  |  | 
|  | tegra_phy = devm_kzalloc(&pdev->dev, sizeof(*tegra_phy), GFP_KERNEL); | 
|  | if (!tegra_phy) | 
|  | return -ENOMEM; | 
|  |  | 
|  | match = of_match_device(tegra_usb_phy_id_table, &pdev->dev); | 
|  | if (!match) { | 
|  | dev_err(&pdev->dev, "Error: No device match found\n"); | 
|  | return -ENODEV; | 
|  | } | 
|  | tegra_phy->soc_config = match->data; | 
|  |  | 
|  | res = platform_get_resource(pdev, IORESOURCE_MEM, 0); | 
|  | if (!res) { | 
|  | dev_err(&pdev->dev, "Failed to get I/O memory\n"); | 
|  | return  -ENXIO; | 
|  | } | 
|  |  | 
|  | tegra_phy->regs = devm_ioremap(&pdev->dev, res->start, | 
|  | resource_size(res)); | 
|  | if (!tegra_phy->regs) { | 
|  | dev_err(&pdev->dev, "Failed to remap I/O memory\n"); | 
|  | return -ENOMEM; | 
|  | } | 
|  |  | 
|  | tegra_phy->is_legacy_phy = | 
|  | of_property_read_bool(np, "nvidia,has-legacy-mode"); | 
|  |  | 
|  | phy_type = of_usb_get_phy_mode(np); | 
|  | switch (phy_type) { | 
|  | case USBPHY_INTERFACE_MODE_UTMI: | 
|  | err = utmi_phy_probe(tegra_phy, pdev); | 
|  | if (err < 0) | 
|  | return err; | 
|  | break; | 
|  |  | 
|  | case USBPHY_INTERFACE_MODE_ULPI: | 
|  | tegra_phy->is_ulpi_phy = true; | 
|  |  | 
|  | tegra_phy->reset_gpio = | 
|  | of_get_named_gpio(np, "nvidia,phy-reset-gpio", 0); | 
|  | if (!gpio_is_valid(tegra_phy->reset_gpio)) { | 
|  | dev_err(&pdev->dev, | 
|  | "Invalid GPIO: %d\n", tegra_phy->reset_gpio); | 
|  | return tegra_phy->reset_gpio; | 
|  | } | 
|  | tegra_phy->config = NULL; | 
|  | break; | 
|  |  | 
|  | default: | 
|  | dev_err(&pdev->dev, "phy_type %u is invalid or unsupported\n", | 
|  | phy_type); | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | if (of_find_property(np, "dr_mode", NULL)) | 
|  | tegra_phy->mode = usb_get_dr_mode(&pdev->dev); | 
|  | else | 
|  | tegra_phy->mode = USB_DR_MODE_HOST; | 
|  |  | 
|  | if (tegra_phy->mode == USB_DR_MODE_UNKNOWN) { | 
|  | dev_err(&pdev->dev, "dr_mode is invalid\n"); | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | /* On some boards, the VBUS regulator doesn't need to be controlled */ | 
|  | if (of_find_property(np, "vbus-supply", NULL)) { | 
|  | tegra_phy->vbus = devm_regulator_get(&pdev->dev, "vbus"); | 
|  | if (IS_ERR(tegra_phy->vbus)) | 
|  | return PTR_ERR(tegra_phy->vbus); | 
|  | } else { | 
|  | dev_notice(&pdev->dev, "no vbus regulator"); | 
|  | tegra_phy->vbus = ERR_PTR(-ENODEV); | 
|  | } | 
|  |  | 
|  | tegra_phy->u_phy.dev = &pdev->dev; | 
|  | err = tegra_usb_phy_init(tegra_phy); | 
|  | if (err < 0) | 
|  | return err; | 
|  |  | 
|  | tegra_phy->u_phy.set_suspend = tegra_usb_phy_suspend; | 
|  |  | 
|  | platform_set_drvdata(pdev, tegra_phy); | 
|  |  | 
|  | err = usb_add_phy_dev(&tegra_phy->u_phy); | 
|  | if (err < 0) { | 
|  | tegra_usb_phy_close(tegra_phy); | 
|  | return err; | 
|  | } | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int tegra_usb_phy_remove(struct platform_device *pdev) | 
|  | { | 
|  | struct tegra_usb_phy *tegra_phy = platform_get_drvdata(pdev); | 
|  |  | 
|  | usb_remove_phy(&tegra_phy->u_phy); | 
|  | tegra_usb_phy_close(tegra_phy); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static struct platform_driver tegra_usb_phy_driver = { | 
|  | .probe		= tegra_usb_phy_probe, | 
|  | .remove		= tegra_usb_phy_remove, | 
|  | .driver		= { | 
|  | .name	= "tegra-phy", | 
|  | .of_match_table = tegra_usb_phy_id_table, | 
|  | }, | 
|  | }; | 
|  | module_platform_driver(tegra_usb_phy_driver); | 
|  |  | 
|  | MODULE_DESCRIPTION("Tegra USB PHY driver"); | 
|  | MODULE_LICENSE("GPL v2"); |