| config MTK_THERMAL |
| tristate "Mediatek thermal drivers" |
| depends on THERMAL_OF |
| help |
| This is the option for Mediatek thermal software |
| solutions. Please enable corresponding options to |
| get temperature information from thermal sensors or |
| turn on throttle mechaisms for thermal mitigation. |
| |
| if MTK_THERMAL |
| |
| config MTK_SOC_THERMAL |
| tristate "Temperature sensor driver for Mediatek SoCs" |
| depends on HAS_IOMEM |
| depends on NVMEM || NVMEM=n |
| depends on RESET_CONTROLLER |
| help |
| Enable this option if you want to get SoC temperature |
| information for Mediatek platforms. This driver |
| configures thermal controllers to collect temperature |
| via AUXADC interface. |
| |
| config MTK_SOC_THERMAL_LVTS |
| tristate "LVTS (Low voltage thermal sensor) driver for Mediatek SoCs" |
| depends on HAS_IOMEM |
| depends on NVMEM |
| depends on RESET_TI_SYSCON |
| help |
| Enable this option if you want to get SoC temperature |
| information for Mediatek platforms. This driver |
| configures LVTS thermal controllers to collect temperatures |
| via ASIF interface. |
| |
| config MTK_BOARD_THERMAL |
| tristate "On-board NTC thermistor driver for Mediatek SoCs" |
| help |
| Enable this option if you want to get PCB temperature |
| via on-board NTC for Mediatek platforms. |
| This driver reads the voltage value from TIA hardware |
| which is responsible for reading all PMIC AUXADC channels |
| sequentially. The address of TIA register for each channel |
| and temperature convert table should be specified in |
| device tree. |
| |
| config MTK_PMIC_THERMAL |
| tristate "PMIC thermal sensor driver for Mediatek SoCs" |
| help |
| Enable this option if you want to get PMIC temperature |
| for Mediatek platforms. |
| This driver reads the voltage value from PMIC AUXADC channels, |
| and converts raw value to PMIC temperature via PMIC efuse data. |
| |
| config MTK_MD_THERMAL |
| tristate "Mediatek Modem cooling framework" |
| depends on MTK_ECCCI_DRIVER |
| help |
| Enable this option to turn on modem throttle mechanisms |
| for Mediatek platforms. |
| This option depends on MTK_ECCCI_DRIVER which is the |
| IPC interface between AP SoC and modem. |
| |
| if MTK_MD_THERMAL |
| |
| config MTK_MD_THERMAL_MUTT |
| tristate "Mediatek modem uplink throughput throttle driver" |
| help |
| Enable this option if you want to use modem |
| uplink throughput throttle cooler for Mediatek |
| platforms. |
| The throttling levels are defined in modem. |
| |
| config MTK_MD_THERMAL_TX_POWER |
| tristate "Mediatek modem TX power throttle driver" |
| help |
| Enable this option if you want use modem TX power |
| throttle cooler for Mediatek platforms. |
| This feature is only supported for mt6297 or later |
| modem platforms. |
| |
| config MTK_MD_THERMAL_SCG_OFF |
| tristate "Mediatek modem SCG cell off driver" |
| help |
| Enable this option if you want use modem SCG cell |
| throttle cooler for Mediatek platforms. |
| This feature is only supported for mt6297 or later |
| modem platforms. |
| |
| config MTK_MD_THERMAL_SYSFS |
| tristate "Mediatek modem throttle sysfs driver" |
| default n |
| help |
| Enable this option if you want to use sysfs debug |
| interface for Mediatek modem coolers. |
| This option should be enabled only for HW power |
| evaluation purpose. |
| endif |
| |
| config MTK_MD_RF_THERMAL |
| tristate "Mediatek modem RF thermal zone driver" |
| depends on MTK_ECCCI_DRIVER |
| help |
| Enable this option if you want to get modem RF |
| temperature information for Mediatek platforms. |
| This driver queries temperature via CCCI interface |
| and handles the feedback from modem in the callback |
| function which is registered to CCCI driver at |
| driver initialization stage. |
| |
| config MTK_THERMAL_IPI |
| tristate "Mediatek thermal IPI interface driver" |
| depends on MTK_TINYSYS_SSPM_SUPPORT |
| help |
| Enable this option if you want to use and communicate |
| with tinysys microprocessors for Mediatek platforms. |
| This driver defines thermal ipi commands and provides an |
| API to send a ipi command to tinysys microprocessors. |
| |
| if MTK_THERMAL_IPI |
| config MTK_THERMAL_TRM |
| tristate "Mediatek thermal risk monitor (TRM) driver" |
| help |
| Enable this option if you want to offload Linux thermal |
| framework (LTF) onto a tinysys microprocesssor when AP MCU |
| suspended. TRM will take it over and keep monitoring |
| temperatures. If a device is going to overheat, TRM will |
| wake AP MCU up and give the control back to LTF. |
| endif |
| endif |