| // SPDX-License-Identifier: GPL-2.0 | 
 | /* | 
 |  * udc.c - ChipIdea UDC driver | 
 |  * | 
 |  * Copyright (C) 2008 Chipidea - MIPS Technologies, Inc. All rights reserved. | 
 |  * | 
 |  * Author: David Lopo | 
 |  */ | 
 |  | 
 | #include <linux/delay.h> | 
 | #include <linux/device.h> | 
 | #include <linux/dmapool.h> | 
 | #include <linux/err.h> | 
 | #include <linux/irqreturn.h> | 
 | #include <linux/kernel.h> | 
 | #include <linux/slab.h> | 
 | #include <linux/pm_runtime.h> | 
 | #include <linux/usb/ch9.h> | 
 | #include <linux/usb/gadget.h> | 
 | #include <linux/usb/otg-fsm.h> | 
 | #include <linux/usb/chipidea.h> | 
 |  | 
 | #include "ci.h" | 
 | #include "udc.h" | 
 | #include "bits.h" | 
 | #include "otg.h" | 
 | #include "otg_fsm.h" | 
 |  | 
 | /* control endpoint description */ | 
 | static const struct usb_endpoint_descriptor | 
 | ctrl_endpt_out_desc = { | 
 | 	.bLength         = USB_DT_ENDPOINT_SIZE, | 
 | 	.bDescriptorType = USB_DT_ENDPOINT, | 
 |  | 
 | 	.bEndpointAddress = USB_DIR_OUT, | 
 | 	.bmAttributes    = USB_ENDPOINT_XFER_CONTROL, | 
 | 	.wMaxPacketSize  = cpu_to_le16(CTRL_PAYLOAD_MAX), | 
 | }; | 
 |  | 
 | static const struct usb_endpoint_descriptor | 
 | ctrl_endpt_in_desc = { | 
 | 	.bLength         = USB_DT_ENDPOINT_SIZE, | 
 | 	.bDescriptorType = USB_DT_ENDPOINT, | 
 |  | 
 | 	.bEndpointAddress = USB_DIR_IN, | 
 | 	.bmAttributes    = USB_ENDPOINT_XFER_CONTROL, | 
 | 	.wMaxPacketSize  = cpu_to_le16(CTRL_PAYLOAD_MAX), | 
 | }; | 
 |  | 
 | /** | 
 |  * hw_ep_bit: calculates the bit number | 
 |  * @num: endpoint number | 
 |  * @dir: endpoint direction | 
 |  * | 
 |  * This function returns bit number | 
 |  */ | 
 | static inline int hw_ep_bit(int num, int dir) | 
 | { | 
 | 	return num + ((dir == TX) ? 16 : 0); | 
 | } | 
 |  | 
 | static inline int ep_to_bit(struct ci_hdrc *ci, int n) | 
 | { | 
 | 	int fill = 16 - ci->hw_ep_max / 2; | 
 |  | 
 | 	if (n >= ci->hw_ep_max / 2) | 
 | 		n += fill; | 
 |  | 
 | 	return n; | 
 | } | 
 |  | 
 | /** | 
 |  * hw_device_state: enables/disables interrupts (execute without interruption) | 
 |  * @dma: 0 => disable, !0 => enable and set dma engine | 
 |  * | 
 |  * This function returns an error code | 
 |  */ | 
 | static int hw_device_state(struct ci_hdrc *ci, u32 dma) | 
 | { | 
 | 	if (dma) { | 
 | 		hw_write(ci, OP_ENDPTLISTADDR, ~0, dma); | 
 | 		/* interrupt, error, port change, reset, sleep/suspend */ | 
 | 		hw_write(ci, OP_USBINTR, ~0, | 
 | 			     USBi_UI|USBi_UEI|USBi_PCI|USBi_URI|USBi_SLI); | 
 | 	} else { | 
 | 		hw_write(ci, OP_USBINTR, ~0, 0); | 
 | 	} | 
 | 	return 0; | 
 | } | 
 |  | 
 | /** | 
 |  * hw_ep_flush: flush endpoint fifo (execute without interruption) | 
 |  * @num: endpoint number | 
 |  * @dir: endpoint direction | 
 |  * | 
 |  * This function returns an error code | 
 |  */ | 
 | static int hw_ep_flush(struct ci_hdrc *ci, int num, int dir) | 
 | { | 
 | 	int n = hw_ep_bit(num, dir); | 
 |  | 
 | 	do { | 
 | 		/* flush any pending transfer */ | 
 | 		hw_write(ci, OP_ENDPTFLUSH, ~0, BIT(n)); | 
 | 		while (hw_read(ci, OP_ENDPTFLUSH, BIT(n))) | 
 | 			cpu_relax(); | 
 | 	} while (hw_read(ci, OP_ENDPTSTAT, BIT(n))); | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | /** | 
 |  * hw_ep_disable: disables endpoint (execute without interruption) | 
 |  * @num: endpoint number | 
 |  * @dir: endpoint direction | 
 |  * | 
 |  * This function returns an error code | 
 |  */ | 
 | static int hw_ep_disable(struct ci_hdrc *ci, int num, int dir) | 
 | { | 
 | 	hw_write(ci, OP_ENDPTCTRL + num, | 
 | 		 (dir == TX) ? ENDPTCTRL_TXE : ENDPTCTRL_RXE, 0); | 
 | 	return 0; | 
 | } | 
 |  | 
 | /** | 
 |  * hw_ep_enable: enables endpoint (execute without interruption) | 
 |  * @num:  endpoint number | 
 |  * @dir:  endpoint direction | 
 |  * @type: endpoint type | 
 |  * | 
 |  * This function returns an error code | 
 |  */ | 
 | static int hw_ep_enable(struct ci_hdrc *ci, int num, int dir, int type) | 
 | { | 
 | 	u32 mask, data; | 
 |  | 
 | 	if (dir == TX) { | 
 | 		mask  = ENDPTCTRL_TXT;  /* type    */ | 
 | 		data  = type << __ffs(mask); | 
 |  | 
 | 		mask |= ENDPTCTRL_TXS;  /* unstall */ | 
 | 		mask |= ENDPTCTRL_TXR;  /* reset data toggle */ | 
 | 		data |= ENDPTCTRL_TXR; | 
 | 		mask |= ENDPTCTRL_TXE;  /* enable  */ | 
 | 		data |= ENDPTCTRL_TXE; | 
 | 	} else { | 
 | 		mask  = ENDPTCTRL_RXT;  /* type    */ | 
 | 		data  = type << __ffs(mask); | 
 |  | 
 | 		mask |= ENDPTCTRL_RXS;  /* unstall */ | 
 | 		mask |= ENDPTCTRL_RXR;  /* reset data toggle */ | 
 | 		data |= ENDPTCTRL_RXR; | 
 | 		mask |= ENDPTCTRL_RXE;  /* enable  */ | 
 | 		data |= ENDPTCTRL_RXE; | 
 | 	} | 
 | 	hw_write(ci, OP_ENDPTCTRL + num, mask, data); | 
 | 	return 0; | 
 | } | 
 |  | 
 | /** | 
 |  * hw_ep_get_halt: return endpoint halt status | 
 |  * @num: endpoint number | 
 |  * @dir: endpoint direction | 
 |  * | 
 |  * This function returns 1 if endpoint halted | 
 |  */ | 
 | static int hw_ep_get_halt(struct ci_hdrc *ci, int num, int dir) | 
 | { | 
 | 	u32 mask = (dir == TX) ? ENDPTCTRL_TXS : ENDPTCTRL_RXS; | 
 |  | 
 | 	return hw_read(ci, OP_ENDPTCTRL + num, mask) ? 1 : 0; | 
 | } | 
 |  | 
 | /** | 
 |  * hw_ep_prime: primes endpoint (execute without interruption) | 
 |  * @num:     endpoint number | 
 |  * @dir:     endpoint direction | 
 |  * @is_ctrl: true if control endpoint | 
 |  * | 
 |  * This function returns an error code | 
 |  */ | 
 | static int hw_ep_prime(struct ci_hdrc *ci, int num, int dir, int is_ctrl) | 
 | { | 
 | 	int n = hw_ep_bit(num, dir); | 
 |  | 
 | 	/* Synchronize before ep prime */ | 
 | 	wmb(); | 
 |  | 
 | 	if (is_ctrl && dir == RX && hw_read(ci, OP_ENDPTSETUPSTAT, BIT(num))) | 
 | 		return -EAGAIN; | 
 |  | 
 | 	hw_write(ci, OP_ENDPTPRIME, ~0, BIT(n)); | 
 |  | 
 | 	while (hw_read(ci, OP_ENDPTPRIME, BIT(n))) | 
 | 		cpu_relax(); | 
 | 	if (is_ctrl && dir == RX && hw_read(ci, OP_ENDPTSETUPSTAT, BIT(num))) | 
 | 		return -EAGAIN; | 
 |  | 
 | 	/* status shoult be tested according with manual but it doesn't work */ | 
 | 	return 0; | 
 | } | 
 |  | 
 | /** | 
 |  * hw_ep_set_halt: configures ep halt & resets data toggle after clear (execute | 
 |  *                 without interruption) | 
 |  * @num:   endpoint number | 
 |  * @dir:   endpoint direction | 
 |  * @value: true => stall, false => unstall | 
 |  * | 
 |  * This function returns an error code | 
 |  */ | 
 | static int hw_ep_set_halt(struct ci_hdrc *ci, int num, int dir, int value) | 
 | { | 
 | 	if (value != 0 && value != 1) | 
 | 		return -EINVAL; | 
 |  | 
 | 	do { | 
 | 		enum ci_hw_regs reg = OP_ENDPTCTRL + num; | 
 | 		u32 mask_xs = (dir == TX) ? ENDPTCTRL_TXS : ENDPTCTRL_RXS; | 
 | 		u32 mask_xr = (dir == TX) ? ENDPTCTRL_TXR : ENDPTCTRL_RXR; | 
 |  | 
 | 		/* data toggle - reserved for EP0 but it's in ESS */ | 
 | 		hw_write(ci, reg, mask_xs|mask_xr, | 
 | 			  value ? mask_xs : mask_xr); | 
 | 	} while (value != hw_ep_get_halt(ci, num, dir)); | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | /** | 
 |  * hw_is_port_high_speed: test if port is high speed | 
 |  * | 
 |  * This function returns true if high speed port | 
 |  */ | 
 | static int hw_port_is_high_speed(struct ci_hdrc *ci) | 
 | { | 
 | 	return ci->hw_bank.lpm ? hw_read(ci, OP_DEVLC, DEVLC_PSPD) : | 
 | 		hw_read(ci, OP_PORTSC, PORTSC_HSP); | 
 | } | 
 |  | 
 | /** | 
 |  * hw_test_and_clear_complete: test & clear complete status (execute without | 
 |  *                             interruption) | 
 |  * @n: endpoint number | 
 |  * | 
 |  * This function returns complete status | 
 |  */ | 
 | static int hw_test_and_clear_complete(struct ci_hdrc *ci, int n) | 
 | { | 
 | 	n = ep_to_bit(ci, n); | 
 | 	return hw_test_and_clear(ci, OP_ENDPTCOMPLETE, BIT(n)); | 
 | } | 
 |  | 
 | /** | 
 |  * hw_test_and_clear_intr_active: test & clear active interrupts (execute | 
 |  *                                without interruption) | 
 |  * | 
 |  * This function returns active interrutps | 
 |  */ | 
 | static u32 hw_test_and_clear_intr_active(struct ci_hdrc *ci) | 
 | { | 
 | 	u32 reg = hw_read_intr_status(ci) & hw_read_intr_enable(ci); | 
 |  | 
 | 	hw_write(ci, OP_USBSTS, ~0, reg); | 
 | 	return reg; | 
 | } | 
 |  | 
 | /** | 
 |  * hw_test_and_clear_setup_guard: test & clear setup guard (execute without | 
 |  *                                interruption) | 
 |  * | 
 |  * This function returns guard value | 
 |  */ | 
 | static int hw_test_and_clear_setup_guard(struct ci_hdrc *ci) | 
 | { | 
 | 	return hw_test_and_write(ci, OP_USBCMD, USBCMD_SUTW, 0); | 
 | } | 
 |  | 
 | /** | 
 |  * hw_test_and_set_setup_guard: test & set setup guard (execute without | 
 |  *                              interruption) | 
 |  * | 
 |  * This function returns guard value | 
 |  */ | 
 | static int hw_test_and_set_setup_guard(struct ci_hdrc *ci) | 
 | { | 
 | 	return hw_test_and_write(ci, OP_USBCMD, USBCMD_SUTW, USBCMD_SUTW); | 
 | } | 
 |  | 
 | /** | 
 |  * hw_usb_set_address: configures USB address (execute without interruption) | 
 |  * @value: new USB address | 
 |  * | 
 |  * This function explicitly sets the address, without the "USBADRA" (advance) | 
 |  * feature, which is not supported by older versions of the controller. | 
 |  */ | 
 | static void hw_usb_set_address(struct ci_hdrc *ci, u8 value) | 
 | { | 
 | 	hw_write(ci, OP_DEVICEADDR, DEVICEADDR_USBADR, | 
 | 		 value << __ffs(DEVICEADDR_USBADR)); | 
 | } | 
 |  | 
 | /** | 
 |  * hw_usb_reset: restart device after a bus reset (execute without | 
 |  *               interruption) | 
 |  * | 
 |  * This function returns an error code | 
 |  */ | 
 | static int hw_usb_reset(struct ci_hdrc *ci) | 
 | { | 
 | 	hw_usb_set_address(ci, 0); | 
 |  | 
 | 	/* ESS flushes only at end?!? */ | 
 | 	hw_write(ci, OP_ENDPTFLUSH,    ~0, ~0); | 
 |  | 
 | 	/* clear setup token semaphores */ | 
 | 	hw_write(ci, OP_ENDPTSETUPSTAT, 0,  0); | 
 |  | 
 | 	/* clear complete status */ | 
 | 	hw_write(ci, OP_ENDPTCOMPLETE,  0,  0); | 
 |  | 
 | 	/* wait until all bits cleared */ | 
 | 	while (hw_read(ci, OP_ENDPTPRIME, ~0)) | 
 | 		udelay(10);             /* not RTOS friendly */ | 
 |  | 
 | 	/* reset all endpoints ? */ | 
 |  | 
 | 	/* reset internal status and wait for further instructions | 
 | 	   no need to verify the port reset status (ESS does it) */ | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | /****************************************************************************** | 
 |  * UTIL block | 
 |  *****************************************************************************/ | 
 |  | 
 | static int add_td_to_list(struct ci_hw_ep *hwep, struct ci_hw_req *hwreq, | 
 | 			  unsigned length) | 
 | { | 
 | 	int i; | 
 | 	u32 temp; | 
 | 	struct td_node *lastnode, *node = kzalloc(sizeof(struct td_node), | 
 | 						  GFP_ATOMIC); | 
 |  | 
 | 	if (node == NULL) | 
 | 		return -ENOMEM; | 
 |  | 
 | 	node->ptr = dma_pool_zalloc(hwep->td_pool, GFP_ATOMIC, &node->dma); | 
 | 	if (node->ptr == NULL) { | 
 | 		kfree(node); | 
 | 		return -ENOMEM; | 
 | 	} | 
 |  | 
 | 	node->ptr->token = cpu_to_le32(length << __ffs(TD_TOTAL_BYTES)); | 
 | 	node->ptr->token &= cpu_to_le32(TD_TOTAL_BYTES); | 
 | 	node->ptr->token |= cpu_to_le32(TD_STATUS_ACTIVE); | 
 | 	if (hwep->type == USB_ENDPOINT_XFER_ISOC && hwep->dir == TX) { | 
 | 		u32 mul = hwreq->req.length / hwep->ep.maxpacket; | 
 |  | 
 | 		if (hwreq->req.length == 0 | 
 | 				|| hwreq->req.length % hwep->ep.maxpacket) | 
 | 			mul++; | 
 | 		node->ptr->token |= cpu_to_le32(mul << __ffs(TD_MULTO)); | 
 | 	} | 
 |  | 
 | 	temp = (u32) (hwreq->req.dma + hwreq->req.actual); | 
 | 	if (length) { | 
 | 		node->ptr->page[0] = cpu_to_le32(temp); | 
 | 		for (i = 1; i < TD_PAGE_COUNT; i++) { | 
 | 			u32 page = temp + i * CI_HDRC_PAGE_SIZE; | 
 | 			page &= ~TD_RESERVED_MASK; | 
 | 			node->ptr->page[i] = cpu_to_le32(page); | 
 | 		} | 
 | 	} | 
 |  | 
 | 	hwreq->req.actual += length; | 
 |  | 
 | 	if (!list_empty(&hwreq->tds)) { | 
 | 		/* get the last entry */ | 
 | 		lastnode = list_entry(hwreq->tds.prev, | 
 | 				struct td_node, td); | 
 | 		lastnode->ptr->next = cpu_to_le32(node->dma); | 
 | 	} | 
 |  | 
 | 	INIT_LIST_HEAD(&node->td); | 
 | 	list_add_tail(&node->td, &hwreq->tds); | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | /** | 
 |  * _usb_addr: calculates endpoint address from direction & number | 
 |  * @ep:  endpoint | 
 |  */ | 
 | static inline u8 _usb_addr(struct ci_hw_ep *ep) | 
 | { | 
 | 	return ((ep->dir == TX) ? USB_ENDPOINT_DIR_MASK : 0) | ep->num; | 
 | } | 
 |  | 
 | /** | 
 |  * _hardware_enqueue: configures a request at hardware level | 
 |  * @hwep:   endpoint | 
 |  * @hwreq:  request | 
 |  * | 
 |  * This function returns an error code | 
 |  */ | 
 | static int _hardware_enqueue(struct ci_hw_ep *hwep, struct ci_hw_req *hwreq) | 
 | { | 
 | 	struct ci_hdrc *ci = hwep->ci; | 
 | 	int ret = 0; | 
 | 	unsigned rest = hwreq->req.length; | 
 | 	int pages = TD_PAGE_COUNT; | 
 | 	struct td_node *firstnode, *lastnode; | 
 |  | 
 | 	/* don't queue twice */ | 
 | 	if (hwreq->req.status == -EALREADY) | 
 | 		return -EALREADY; | 
 |  | 
 | 	hwreq->req.status = -EALREADY; | 
 |  | 
 | 	ret = usb_gadget_map_request_by_dev(ci->dev->parent, | 
 | 					    &hwreq->req, hwep->dir); | 
 | 	if (ret) | 
 | 		return ret; | 
 |  | 
 | 	/* | 
 | 	 * The first buffer could be not page aligned. | 
 | 	 * In that case we have to span into one extra td. | 
 | 	 */ | 
 | 	if (hwreq->req.dma % PAGE_SIZE) | 
 | 		pages--; | 
 |  | 
 | 	if (rest == 0) { | 
 | 		ret = add_td_to_list(hwep, hwreq, 0); | 
 | 		if (ret < 0) | 
 | 			goto done; | 
 | 	} | 
 |  | 
 | 	while (rest > 0) { | 
 | 		unsigned count = min(hwreq->req.length - hwreq->req.actual, | 
 | 					(unsigned)(pages * CI_HDRC_PAGE_SIZE)); | 
 | 		ret = add_td_to_list(hwep, hwreq, count); | 
 | 		if (ret < 0) | 
 | 			goto done; | 
 |  | 
 | 		rest -= count; | 
 | 	} | 
 |  | 
 | 	if (hwreq->req.zero && hwreq->req.length && hwep->dir == TX | 
 | 	    && (hwreq->req.length % hwep->ep.maxpacket == 0)) { | 
 | 		ret = add_td_to_list(hwep, hwreq, 0); | 
 | 		if (ret < 0) | 
 | 			goto done; | 
 | 	} | 
 |  | 
 | 	firstnode = list_first_entry(&hwreq->tds, struct td_node, td); | 
 |  | 
 | 	lastnode = list_entry(hwreq->tds.prev, | 
 | 		struct td_node, td); | 
 |  | 
 | 	lastnode->ptr->next = cpu_to_le32(TD_TERMINATE); | 
 | 	if (!hwreq->req.no_interrupt) | 
 | 		lastnode->ptr->token |= cpu_to_le32(TD_IOC); | 
 | 	wmb(); | 
 |  | 
 | 	hwreq->req.actual = 0; | 
 | 	if (!list_empty(&hwep->qh.queue)) { | 
 | 		struct ci_hw_req *hwreqprev; | 
 | 		int n = hw_ep_bit(hwep->num, hwep->dir); | 
 | 		int tmp_stat; | 
 | 		struct td_node *prevlastnode; | 
 | 		u32 next = firstnode->dma & TD_ADDR_MASK; | 
 |  | 
 | 		hwreqprev = list_entry(hwep->qh.queue.prev, | 
 | 				struct ci_hw_req, queue); | 
 | 		prevlastnode = list_entry(hwreqprev->tds.prev, | 
 | 				struct td_node, td); | 
 |  | 
 | 		prevlastnode->ptr->next = cpu_to_le32(next); | 
 | 		wmb(); | 
 | 		if (hw_read(ci, OP_ENDPTPRIME, BIT(n))) | 
 | 			goto done; | 
 | 		do { | 
 | 			hw_write(ci, OP_USBCMD, USBCMD_ATDTW, USBCMD_ATDTW); | 
 | 			tmp_stat = hw_read(ci, OP_ENDPTSTAT, BIT(n)); | 
 | 		} while (!hw_read(ci, OP_USBCMD, USBCMD_ATDTW)); | 
 | 		hw_write(ci, OP_USBCMD, USBCMD_ATDTW, 0); | 
 | 		if (tmp_stat) | 
 | 			goto done; | 
 | 	} | 
 |  | 
 | 	/*  QH configuration */ | 
 | 	hwep->qh.ptr->td.next = cpu_to_le32(firstnode->dma); | 
 | 	hwep->qh.ptr->td.token &= | 
 | 		cpu_to_le32(~(TD_STATUS_HALTED|TD_STATUS_ACTIVE)); | 
 |  | 
 | 	if (hwep->type == USB_ENDPOINT_XFER_ISOC && hwep->dir == RX) { | 
 | 		u32 mul = hwreq->req.length / hwep->ep.maxpacket; | 
 |  | 
 | 		if (hwreq->req.length == 0 | 
 | 				|| hwreq->req.length % hwep->ep.maxpacket) | 
 | 			mul++; | 
 | 		hwep->qh.ptr->cap |= cpu_to_le32(mul << __ffs(QH_MULT)); | 
 | 	} | 
 |  | 
 | 	ret = hw_ep_prime(ci, hwep->num, hwep->dir, | 
 | 			   hwep->type == USB_ENDPOINT_XFER_CONTROL); | 
 | done: | 
 | 	return ret; | 
 | } | 
 |  | 
 | /* | 
 |  * free_pending_td: remove a pending request for the endpoint | 
 |  * @hwep: endpoint | 
 |  */ | 
 | static void free_pending_td(struct ci_hw_ep *hwep) | 
 | { | 
 | 	struct td_node *pending = hwep->pending_td; | 
 |  | 
 | 	dma_pool_free(hwep->td_pool, pending->ptr, pending->dma); | 
 | 	hwep->pending_td = NULL; | 
 | 	kfree(pending); | 
 | } | 
 |  | 
 | static int reprime_dtd(struct ci_hdrc *ci, struct ci_hw_ep *hwep, | 
 | 					   struct td_node *node) | 
 | { | 
 | 	hwep->qh.ptr->td.next = cpu_to_le32(node->dma); | 
 | 	hwep->qh.ptr->td.token &= | 
 | 		cpu_to_le32(~(TD_STATUS_HALTED | TD_STATUS_ACTIVE)); | 
 |  | 
 | 	return hw_ep_prime(ci, hwep->num, hwep->dir, | 
 | 				hwep->type == USB_ENDPOINT_XFER_CONTROL); | 
 | } | 
 |  | 
 | /** | 
 |  * _hardware_dequeue: handles a request at hardware level | 
 |  * @gadget: gadget | 
 |  * @hwep:   endpoint | 
 |  * | 
 |  * This function returns an error code | 
 |  */ | 
 | static int _hardware_dequeue(struct ci_hw_ep *hwep, struct ci_hw_req *hwreq) | 
 | { | 
 | 	u32 tmptoken; | 
 | 	struct td_node *node, *tmpnode; | 
 | 	unsigned remaining_length; | 
 | 	unsigned actual = hwreq->req.length; | 
 | 	struct ci_hdrc *ci = hwep->ci; | 
 |  | 
 | 	if (hwreq->req.status != -EALREADY) | 
 | 		return -EINVAL; | 
 |  | 
 | 	hwreq->req.status = 0; | 
 |  | 
 | 	list_for_each_entry_safe(node, tmpnode, &hwreq->tds, td) { | 
 | 		tmptoken = le32_to_cpu(node->ptr->token); | 
 | 		if ((TD_STATUS_ACTIVE & tmptoken) != 0) { | 
 | 			int n = hw_ep_bit(hwep->num, hwep->dir); | 
 |  | 
 | 			if (ci->rev == CI_REVISION_24) | 
 | 				if (!hw_read(ci, OP_ENDPTSTAT, BIT(n))) | 
 | 					reprime_dtd(ci, hwep, node); | 
 | 			hwreq->req.status = -EALREADY; | 
 | 			return -EBUSY; | 
 | 		} | 
 |  | 
 | 		remaining_length = (tmptoken & TD_TOTAL_BYTES); | 
 | 		remaining_length >>= __ffs(TD_TOTAL_BYTES); | 
 | 		actual -= remaining_length; | 
 |  | 
 | 		hwreq->req.status = tmptoken & TD_STATUS; | 
 | 		if ((TD_STATUS_HALTED & hwreq->req.status)) { | 
 | 			hwreq->req.status = -EPIPE; | 
 | 			break; | 
 | 		} else if ((TD_STATUS_DT_ERR & hwreq->req.status)) { | 
 | 			hwreq->req.status = -EPROTO; | 
 | 			break; | 
 | 		} else if ((TD_STATUS_TR_ERR & hwreq->req.status)) { | 
 | 			hwreq->req.status = -EILSEQ; | 
 | 			break; | 
 | 		} | 
 |  | 
 | 		if (remaining_length) { | 
 | 			if (hwep->dir == TX) { | 
 | 				hwreq->req.status = -EPROTO; | 
 | 				break; | 
 | 			} | 
 | 		} | 
 | 		/* | 
 | 		 * As the hardware could still address the freed td | 
 | 		 * which will run the udc unusable, the cleanup of the | 
 | 		 * td has to be delayed by one. | 
 | 		 */ | 
 | 		if (hwep->pending_td) | 
 | 			free_pending_td(hwep); | 
 |  | 
 | 		hwep->pending_td = node; | 
 | 		list_del_init(&node->td); | 
 | 	} | 
 |  | 
 | 	usb_gadget_unmap_request_by_dev(hwep->ci->dev->parent, | 
 | 					&hwreq->req, hwep->dir); | 
 |  | 
 | 	hwreq->req.actual += actual; | 
 |  | 
 | 	if (hwreq->req.status) | 
 | 		return hwreq->req.status; | 
 |  | 
 | 	return hwreq->req.actual; | 
 | } | 
 |  | 
 | /** | 
 |  * _ep_nuke: dequeues all endpoint requests | 
 |  * @hwep: endpoint | 
 |  * | 
 |  * This function returns an error code | 
 |  * Caller must hold lock | 
 |  */ | 
 | static int _ep_nuke(struct ci_hw_ep *hwep) | 
 | __releases(hwep->lock) | 
 | __acquires(hwep->lock) | 
 | { | 
 | 	struct td_node *node, *tmpnode; | 
 | 	if (hwep == NULL) | 
 | 		return -EINVAL; | 
 |  | 
 | 	hw_ep_flush(hwep->ci, hwep->num, hwep->dir); | 
 |  | 
 | 	while (!list_empty(&hwep->qh.queue)) { | 
 |  | 
 | 		/* pop oldest request */ | 
 | 		struct ci_hw_req *hwreq = list_entry(hwep->qh.queue.next, | 
 | 						     struct ci_hw_req, queue); | 
 |  | 
 | 		list_for_each_entry_safe(node, tmpnode, &hwreq->tds, td) { | 
 | 			dma_pool_free(hwep->td_pool, node->ptr, node->dma); | 
 | 			list_del_init(&node->td); | 
 | 			node->ptr = NULL; | 
 | 			kfree(node); | 
 | 		} | 
 |  | 
 | 		list_del_init(&hwreq->queue); | 
 | 		hwreq->req.status = -ESHUTDOWN; | 
 |  | 
 | 		if (hwreq->req.complete != NULL) { | 
 | 			spin_unlock(hwep->lock); | 
 | 			usb_gadget_giveback_request(&hwep->ep, &hwreq->req); | 
 | 			spin_lock(hwep->lock); | 
 | 		} | 
 | 	} | 
 |  | 
 | 	if (hwep->pending_td) | 
 | 		free_pending_td(hwep); | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | static int _ep_set_halt(struct usb_ep *ep, int value, bool check_transfer) | 
 | { | 
 | 	struct ci_hw_ep *hwep = container_of(ep, struct ci_hw_ep, ep); | 
 | 	int direction, retval = 0; | 
 | 	unsigned long flags; | 
 |  | 
 | 	if (ep == NULL || hwep->ep.desc == NULL) | 
 | 		return -EINVAL; | 
 |  | 
 | 	if (usb_endpoint_xfer_isoc(hwep->ep.desc)) | 
 | 		return -EOPNOTSUPP; | 
 |  | 
 | 	spin_lock_irqsave(hwep->lock, flags); | 
 |  | 
 | 	if (value && hwep->dir == TX && check_transfer && | 
 | 		!list_empty(&hwep->qh.queue) && | 
 | 			!usb_endpoint_xfer_control(hwep->ep.desc)) { | 
 | 		spin_unlock_irqrestore(hwep->lock, flags); | 
 | 		return -EAGAIN; | 
 | 	} | 
 |  | 
 | 	direction = hwep->dir; | 
 | 	do { | 
 | 		retval |= hw_ep_set_halt(hwep->ci, hwep->num, hwep->dir, value); | 
 |  | 
 | 		if (!value) | 
 | 			hwep->wedge = 0; | 
 |  | 
 | 		if (hwep->type == USB_ENDPOINT_XFER_CONTROL) | 
 | 			hwep->dir = (hwep->dir == TX) ? RX : TX; | 
 |  | 
 | 	} while (hwep->dir != direction); | 
 |  | 
 | 	spin_unlock_irqrestore(hwep->lock, flags); | 
 | 	return retval; | 
 | } | 
 |  | 
 |  | 
 | /** | 
 |  * _gadget_stop_activity: stops all USB activity, flushes & disables all endpts | 
 |  * @gadget: gadget | 
 |  * | 
 |  * This function returns an error code | 
 |  */ | 
 | static int _gadget_stop_activity(struct usb_gadget *gadget) | 
 | { | 
 | 	struct usb_ep *ep; | 
 | 	struct ci_hdrc    *ci = container_of(gadget, struct ci_hdrc, gadget); | 
 | 	unsigned long flags; | 
 |  | 
 | 	/* flush all endpoints */ | 
 | 	gadget_for_each_ep(ep, gadget) { | 
 | 		usb_ep_fifo_flush(ep); | 
 | 	} | 
 | 	usb_ep_fifo_flush(&ci->ep0out->ep); | 
 | 	usb_ep_fifo_flush(&ci->ep0in->ep); | 
 |  | 
 | 	/* make sure to disable all endpoints */ | 
 | 	gadget_for_each_ep(ep, gadget) { | 
 | 		usb_ep_disable(ep); | 
 | 	} | 
 |  | 
 | 	if (ci->status != NULL) { | 
 | 		usb_ep_free_request(&ci->ep0in->ep, ci->status); | 
 | 		ci->status = NULL; | 
 | 	} | 
 |  | 
 | 	spin_lock_irqsave(&ci->lock, flags); | 
 | 	ci->gadget.speed = USB_SPEED_UNKNOWN; | 
 | 	ci->remote_wakeup = 0; | 
 | 	ci->suspended = 0; | 
 | 	spin_unlock_irqrestore(&ci->lock, flags); | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | /****************************************************************************** | 
 |  * ISR block | 
 |  *****************************************************************************/ | 
 | /** | 
 |  * isr_reset_handler: USB reset interrupt handler | 
 |  * @ci: UDC device | 
 |  * | 
 |  * This function resets USB engine after a bus reset occurred | 
 |  */ | 
 | static void isr_reset_handler(struct ci_hdrc *ci) | 
 | __releases(ci->lock) | 
 | __acquires(ci->lock) | 
 | { | 
 | 	int retval; | 
 |  | 
 | 	spin_unlock(&ci->lock); | 
 | 	if (ci->gadget.speed != USB_SPEED_UNKNOWN) | 
 | 		usb_gadget_udc_reset(&ci->gadget, ci->driver); | 
 |  | 
 | 	retval = _gadget_stop_activity(&ci->gadget); | 
 | 	if (retval) | 
 | 		goto done; | 
 |  | 
 | 	retval = hw_usb_reset(ci); | 
 | 	if (retval) | 
 | 		goto done; | 
 |  | 
 | 	ci->status = usb_ep_alloc_request(&ci->ep0in->ep, GFP_ATOMIC); | 
 | 	if (ci->status == NULL) | 
 | 		retval = -ENOMEM; | 
 |  | 
 | done: | 
 | 	spin_lock(&ci->lock); | 
 |  | 
 | 	if (retval) | 
 | 		dev_err(ci->dev, "error: %i\n", retval); | 
 | } | 
 |  | 
 | /** | 
 |  * isr_get_status_complete: get_status request complete function | 
 |  * @ep:  endpoint | 
 |  * @req: request handled | 
 |  * | 
 |  * Caller must release lock | 
 |  */ | 
 | static void isr_get_status_complete(struct usb_ep *ep, struct usb_request *req) | 
 | { | 
 | 	if (ep == NULL || req == NULL) | 
 | 		return; | 
 |  | 
 | 	kfree(req->buf); | 
 | 	usb_ep_free_request(ep, req); | 
 | } | 
 |  | 
 | /** | 
 |  * _ep_queue: queues (submits) an I/O request to an endpoint | 
 |  * @ep:        endpoint | 
 |  * @req:       request | 
 |  * @gfp_flags: GFP flags (not used) | 
 |  * | 
 |  * Caller must hold lock | 
 |  * This function returns an error code | 
 |  */ | 
 | static int _ep_queue(struct usb_ep *ep, struct usb_request *req, | 
 | 		    gfp_t __maybe_unused gfp_flags) | 
 | { | 
 | 	struct ci_hw_ep  *hwep  = container_of(ep,  struct ci_hw_ep, ep); | 
 | 	struct ci_hw_req *hwreq = container_of(req, struct ci_hw_req, req); | 
 | 	struct ci_hdrc *ci = hwep->ci; | 
 | 	int retval = 0; | 
 |  | 
 | 	if (ep == NULL || req == NULL || hwep->ep.desc == NULL) | 
 | 		return -EINVAL; | 
 |  | 
 | 	if (hwep->type == USB_ENDPOINT_XFER_CONTROL) { | 
 | 		if (req->length) | 
 | 			hwep = (ci->ep0_dir == RX) ? | 
 | 			       ci->ep0out : ci->ep0in; | 
 | 		if (!list_empty(&hwep->qh.queue)) { | 
 | 			_ep_nuke(hwep); | 
 | 			dev_warn(hwep->ci->dev, "endpoint ctrl %X nuked\n", | 
 | 				 _usb_addr(hwep)); | 
 | 		} | 
 | 	} | 
 |  | 
 | 	if (usb_endpoint_xfer_isoc(hwep->ep.desc) && | 
 | 	    hwreq->req.length > hwep->ep.mult * hwep->ep.maxpacket) { | 
 | 		dev_err(hwep->ci->dev, "request length too big for isochronous\n"); | 
 | 		return -EMSGSIZE; | 
 | 	} | 
 |  | 
 | 	/* first nuke then test link, e.g. previous status has not sent */ | 
 | 	if (!list_empty(&hwreq->queue)) { | 
 | 		dev_err(hwep->ci->dev, "request already in queue\n"); | 
 | 		return -EBUSY; | 
 | 	} | 
 |  | 
 | 	/* push request */ | 
 | 	hwreq->req.status = -EINPROGRESS; | 
 | 	hwreq->req.actual = 0; | 
 |  | 
 | 	retval = _hardware_enqueue(hwep, hwreq); | 
 |  | 
 | 	if (retval == -EALREADY) | 
 | 		retval = 0; | 
 | 	if (!retval) | 
 | 		list_add_tail(&hwreq->queue, &hwep->qh.queue); | 
 |  | 
 | 	return retval; | 
 | } | 
 |  | 
 | /** | 
 |  * isr_get_status_response: get_status request response | 
 |  * @ci: ci struct | 
 |  * @setup: setup request packet | 
 |  * | 
 |  * This function returns an error code | 
 |  */ | 
 | static int isr_get_status_response(struct ci_hdrc *ci, | 
 | 				   struct usb_ctrlrequest *setup) | 
 | __releases(hwep->lock) | 
 | __acquires(hwep->lock) | 
 | { | 
 | 	struct ci_hw_ep *hwep = ci->ep0in; | 
 | 	struct usb_request *req = NULL; | 
 | 	gfp_t gfp_flags = GFP_ATOMIC; | 
 | 	int dir, num, retval; | 
 |  | 
 | 	if (hwep == NULL || setup == NULL) | 
 | 		return -EINVAL; | 
 |  | 
 | 	spin_unlock(hwep->lock); | 
 | 	req = usb_ep_alloc_request(&hwep->ep, gfp_flags); | 
 | 	spin_lock(hwep->lock); | 
 | 	if (req == NULL) | 
 | 		return -ENOMEM; | 
 |  | 
 | 	req->complete = isr_get_status_complete; | 
 | 	req->length   = 2; | 
 | 	req->buf      = kzalloc(req->length, gfp_flags); | 
 | 	if (req->buf == NULL) { | 
 | 		retval = -ENOMEM; | 
 | 		goto err_free_req; | 
 | 	} | 
 |  | 
 | 	if ((setup->bRequestType & USB_RECIP_MASK) == USB_RECIP_DEVICE) { | 
 | 		*(u16 *)req->buf = (ci->remote_wakeup << 1) | | 
 | 			ci->gadget.is_selfpowered; | 
 | 	} else if ((setup->bRequestType & USB_RECIP_MASK) \ | 
 | 		   == USB_RECIP_ENDPOINT) { | 
 | 		dir = (le16_to_cpu(setup->wIndex) & USB_ENDPOINT_DIR_MASK) ? | 
 | 			TX : RX; | 
 | 		num =  le16_to_cpu(setup->wIndex) & USB_ENDPOINT_NUMBER_MASK; | 
 | 		*(u16 *)req->buf = hw_ep_get_halt(ci, num, dir); | 
 | 	} | 
 | 	/* else do nothing; reserved for future use */ | 
 |  | 
 | 	retval = _ep_queue(&hwep->ep, req, gfp_flags); | 
 | 	if (retval) | 
 | 		goto err_free_buf; | 
 |  | 
 | 	return 0; | 
 |  | 
 |  err_free_buf: | 
 | 	kfree(req->buf); | 
 |  err_free_req: | 
 | 	spin_unlock(hwep->lock); | 
 | 	usb_ep_free_request(&hwep->ep, req); | 
 | 	spin_lock(hwep->lock); | 
 | 	return retval; | 
 | } | 
 |  | 
 | /** | 
 |  * isr_setup_status_complete: setup_status request complete function | 
 |  * @ep:  endpoint | 
 |  * @req: request handled | 
 |  * | 
 |  * Caller must release lock. Put the port in test mode if test mode | 
 |  * feature is selected. | 
 |  */ | 
 | static void | 
 | isr_setup_status_complete(struct usb_ep *ep, struct usb_request *req) | 
 | { | 
 | 	struct ci_hdrc *ci = req->context; | 
 | 	unsigned long flags; | 
 |  | 
 | 	if (ci->setaddr) { | 
 | 		hw_usb_set_address(ci, ci->address); | 
 | 		ci->setaddr = false; | 
 | 		if (ci->address) | 
 | 			usb_gadget_set_state(&ci->gadget, USB_STATE_ADDRESS); | 
 | 	} | 
 |  | 
 | 	spin_lock_irqsave(&ci->lock, flags); | 
 | 	if (ci->test_mode) | 
 | 		hw_port_test_set(ci, ci->test_mode); | 
 | 	spin_unlock_irqrestore(&ci->lock, flags); | 
 | } | 
 |  | 
 | /** | 
 |  * isr_setup_status_phase: queues the status phase of a setup transation | 
 |  * @ci: ci struct | 
 |  * | 
 |  * This function returns an error code | 
 |  */ | 
 | static int isr_setup_status_phase(struct ci_hdrc *ci) | 
 | { | 
 | 	struct ci_hw_ep *hwep; | 
 |  | 
 | 	/* | 
 | 	 * Unexpected USB controller behavior, caused by bad signal integrity | 
 | 	 * or ground reference problems, can lead to isr_setup_status_phase | 
 | 	 * being called with ci->status equal to NULL. | 
 | 	 * If this situation occurs, you should review your USB hardware design. | 
 | 	 */ | 
 | 	if (WARN_ON_ONCE(!ci->status)) | 
 | 		return -EPIPE; | 
 |  | 
 | 	hwep = (ci->ep0_dir == TX) ? ci->ep0out : ci->ep0in; | 
 | 	ci->status->context = ci; | 
 | 	ci->status->complete = isr_setup_status_complete; | 
 |  | 
 | 	return _ep_queue(&hwep->ep, ci->status, GFP_ATOMIC); | 
 | } | 
 |  | 
 | /** | 
 |  * isr_tr_complete_low: transaction complete low level handler | 
 |  * @hwep: endpoint | 
 |  * | 
 |  * This function returns an error code | 
 |  * Caller must hold lock | 
 |  */ | 
 | static int isr_tr_complete_low(struct ci_hw_ep *hwep) | 
 | __releases(hwep->lock) | 
 | __acquires(hwep->lock) | 
 | { | 
 | 	struct ci_hw_req *hwreq, *hwreqtemp; | 
 | 	struct ci_hw_ep *hweptemp = hwep; | 
 | 	int retval = 0; | 
 |  | 
 | 	list_for_each_entry_safe(hwreq, hwreqtemp, &hwep->qh.queue, | 
 | 			queue) { | 
 | 		retval = _hardware_dequeue(hwep, hwreq); | 
 | 		if (retval < 0) | 
 | 			break; | 
 | 		list_del_init(&hwreq->queue); | 
 | 		if (hwreq->req.complete != NULL) { | 
 | 			spin_unlock(hwep->lock); | 
 | 			if ((hwep->type == USB_ENDPOINT_XFER_CONTROL) && | 
 | 					hwreq->req.length) | 
 | 				hweptemp = hwep->ci->ep0in; | 
 | 			usb_gadget_giveback_request(&hweptemp->ep, &hwreq->req); | 
 | 			spin_lock(hwep->lock); | 
 | 		} | 
 | 	} | 
 |  | 
 | 	if (retval == -EBUSY) | 
 | 		retval = 0; | 
 |  | 
 | 	return retval; | 
 | } | 
 |  | 
 | static int otg_a_alt_hnp_support(struct ci_hdrc *ci) | 
 | { | 
 | 	dev_warn(&ci->gadget.dev, | 
 | 		"connect the device to an alternate port if you want HNP\n"); | 
 | 	return isr_setup_status_phase(ci); | 
 | } | 
 |  | 
 | /** | 
 |  * isr_setup_packet_handler: setup packet handler | 
 |  * @ci: UDC descriptor | 
 |  * | 
 |  * This function handles setup packet  | 
 |  */ | 
 | static void isr_setup_packet_handler(struct ci_hdrc *ci) | 
 | __releases(ci->lock) | 
 | __acquires(ci->lock) | 
 | { | 
 | 	struct ci_hw_ep *hwep = &ci->ci_hw_ep[0]; | 
 | 	struct usb_ctrlrequest req; | 
 | 	int type, num, dir, err = -EINVAL; | 
 | 	u8 tmode = 0; | 
 |  | 
 | 	/* | 
 | 	 * Flush data and handshake transactions of previous | 
 | 	 * setup packet. | 
 | 	 */ | 
 | 	_ep_nuke(ci->ep0out); | 
 | 	_ep_nuke(ci->ep0in); | 
 |  | 
 | 	/* read_setup_packet */ | 
 | 	do { | 
 | 		hw_test_and_set_setup_guard(ci); | 
 | 		memcpy(&req, &hwep->qh.ptr->setup, sizeof(req)); | 
 | 	} while (!hw_test_and_clear_setup_guard(ci)); | 
 |  | 
 | 	type = req.bRequestType; | 
 |  | 
 | 	ci->ep0_dir = (type & USB_DIR_IN) ? TX : RX; | 
 |  | 
 | 	switch (req.bRequest) { | 
 | 	case USB_REQ_CLEAR_FEATURE: | 
 | 		if (type == (USB_DIR_OUT|USB_RECIP_ENDPOINT) && | 
 | 				le16_to_cpu(req.wValue) == | 
 | 				USB_ENDPOINT_HALT) { | 
 | 			if (req.wLength != 0) | 
 | 				break; | 
 | 			num  = le16_to_cpu(req.wIndex); | 
 | 			dir = (num & USB_ENDPOINT_DIR_MASK) ? TX : RX; | 
 | 			num &= USB_ENDPOINT_NUMBER_MASK; | 
 | 			if (dir == TX) | 
 | 				num += ci->hw_ep_max / 2; | 
 | 			if (!ci->ci_hw_ep[num].wedge) { | 
 | 				spin_unlock(&ci->lock); | 
 | 				err = usb_ep_clear_halt( | 
 | 					&ci->ci_hw_ep[num].ep); | 
 | 				spin_lock(&ci->lock); | 
 | 				if (err) | 
 | 					break; | 
 | 			} | 
 | 			err = isr_setup_status_phase(ci); | 
 | 		} else if (type == (USB_DIR_OUT|USB_RECIP_DEVICE) && | 
 | 				le16_to_cpu(req.wValue) == | 
 | 				USB_DEVICE_REMOTE_WAKEUP) { | 
 | 			if (req.wLength != 0) | 
 | 				break; | 
 | 			ci->remote_wakeup = 0; | 
 | 			err = isr_setup_status_phase(ci); | 
 | 		} else { | 
 | 			goto delegate; | 
 | 		} | 
 | 		break; | 
 | 	case USB_REQ_GET_STATUS: | 
 | 		if ((type != (USB_DIR_IN|USB_RECIP_DEVICE) || | 
 | 			le16_to_cpu(req.wIndex) == OTG_STS_SELECTOR) && | 
 | 		    type != (USB_DIR_IN|USB_RECIP_ENDPOINT) && | 
 | 		    type != (USB_DIR_IN|USB_RECIP_INTERFACE)) | 
 | 			goto delegate; | 
 | 		if (le16_to_cpu(req.wLength) != 2 || | 
 | 		    le16_to_cpu(req.wValue)  != 0) | 
 | 			break; | 
 | 		err = isr_get_status_response(ci, &req); | 
 | 		break; | 
 | 	case USB_REQ_SET_ADDRESS: | 
 | 		if (type != (USB_DIR_OUT|USB_RECIP_DEVICE)) | 
 | 			goto delegate; | 
 | 		if (le16_to_cpu(req.wLength) != 0 || | 
 | 		    le16_to_cpu(req.wIndex)  != 0) | 
 | 			break; | 
 | 		ci->address = (u8)le16_to_cpu(req.wValue); | 
 | 		ci->setaddr = true; | 
 | 		err = isr_setup_status_phase(ci); | 
 | 		break; | 
 | 	case USB_REQ_SET_FEATURE: | 
 | 		if (type == (USB_DIR_OUT|USB_RECIP_ENDPOINT) && | 
 | 				le16_to_cpu(req.wValue) == | 
 | 				USB_ENDPOINT_HALT) { | 
 | 			if (req.wLength != 0) | 
 | 				break; | 
 | 			num  = le16_to_cpu(req.wIndex); | 
 | 			dir = (num & USB_ENDPOINT_DIR_MASK) ? TX : RX; | 
 | 			num &= USB_ENDPOINT_NUMBER_MASK; | 
 | 			if (dir == TX) | 
 | 				num += ci->hw_ep_max / 2; | 
 |  | 
 | 			spin_unlock(&ci->lock); | 
 | 			err = _ep_set_halt(&ci->ci_hw_ep[num].ep, 1, false); | 
 | 			spin_lock(&ci->lock); | 
 | 			if (!err) | 
 | 				isr_setup_status_phase(ci); | 
 | 		} else if (type == (USB_DIR_OUT|USB_RECIP_DEVICE)) { | 
 | 			if (req.wLength != 0) | 
 | 				break; | 
 | 			switch (le16_to_cpu(req.wValue)) { | 
 | 			case USB_DEVICE_REMOTE_WAKEUP: | 
 | 				ci->remote_wakeup = 1; | 
 | 				err = isr_setup_status_phase(ci); | 
 | 				break; | 
 | 			case USB_DEVICE_TEST_MODE: | 
 | 				tmode = le16_to_cpu(req.wIndex) >> 8; | 
 | 				switch (tmode) { | 
 | 				case TEST_J: | 
 | 				case TEST_K: | 
 | 				case TEST_SE0_NAK: | 
 | 				case TEST_PACKET: | 
 | 				case TEST_FORCE_EN: | 
 | 					ci->test_mode = tmode; | 
 | 					err = isr_setup_status_phase( | 
 | 							ci); | 
 | 					break; | 
 | 				default: | 
 | 					break; | 
 | 				} | 
 | 				break; | 
 | 			case USB_DEVICE_B_HNP_ENABLE: | 
 | 				if (ci_otg_is_fsm_mode(ci)) { | 
 | 					ci->gadget.b_hnp_enable = 1; | 
 | 					err = isr_setup_status_phase( | 
 | 							ci); | 
 | 				} | 
 | 				break; | 
 | 			case USB_DEVICE_A_ALT_HNP_SUPPORT: | 
 | 				if (ci_otg_is_fsm_mode(ci)) | 
 | 					err = otg_a_alt_hnp_support(ci); | 
 | 				break; | 
 | 			case USB_DEVICE_A_HNP_SUPPORT: | 
 | 				if (ci_otg_is_fsm_mode(ci)) { | 
 | 					ci->gadget.a_hnp_support = 1; | 
 | 					err = isr_setup_status_phase( | 
 | 							ci); | 
 | 				} | 
 | 				break; | 
 | 			default: | 
 | 				goto delegate; | 
 | 			} | 
 | 		} else { | 
 | 			goto delegate; | 
 | 		} | 
 | 		break; | 
 | 	default: | 
 | delegate: | 
 | 		if (req.wLength == 0)   /* no data phase */ | 
 | 			ci->ep0_dir = TX; | 
 |  | 
 | 		spin_unlock(&ci->lock); | 
 | 		err = ci->driver->setup(&ci->gadget, &req); | 
 | 		spin_lock(&ci->lock); | 
 | 		break; | 
 | 	} | 
 |  | 
 | 	if (err < 0) { | 
 | 		spin_unlock(&ci->lock); | 
 | 		if (_ep_set_halt(&hwep->ep, 1, false)) | 
 | 			dev_err(ci->dev, "error: _ep_set_halt\n"); | 
 | 		spin_lock(&ci->lock); | 
 | 	} | 
 | } | 
 |  | 
 | /** | 
 |  * isr_tr_complete_handler: transaction complete interrupt handler | 
 |  * @ci: UDC descriptor | 
 |  * | 
 |  * This function handles traffic events | 
 |  */ | 
 | static void isr_tr_complete_handler(struct ci_hdrc *ci) | 
 | __releases(ci->lock) | 
 | __acquires(ci->lock) | 
 | { | 
 | 	unsigned i; | 
 | 	int err; | 
 |  | 
 | 	for (i = 0; i < ci->hw_ep_max; i++) { | 
 | 		struct ci_hw_ep *hwep  = &ci->ci_hw_ep[i]; | 
 |  | 
 | 		if (hwep->ep.desc == NULL) | 
 | 			continue;   /* not configured */ | 
 |  | 
 | 		if (hw_test_and_clear_complete(ci, i)) { | 
 | 			err = isr_tr_complete_low(hwep); | 
 | 			if (hwep->type == USB_ENDPOINT_XFER_CONTROL) { | 
 | 				if (err > 0)   /* needs status phase */ | 
 | 					err = isr_setup_status_phase(ci); | 
 | 				if (err < 0) { | 
 | 					spin_unlock(&ci->lock); | 
 | 					if (_ep_set_halt(&hwep->ep, 1, false)) | 
 | 						dev_err(ci->dev, | 
 | 						"error: _ep_set_halt\n"); | 
 | 					spin_lock(&ci->lock); | 
 | 				} | 
 | 			} | 
 | 		} | 
 |  | 
 | 		/* Only handle setup packet below */ | 
 | 		if (i == 0 && | 
 | 			hw_test_and_clear(ci, OP_ENDPTSETUPSTAT, BIT(0))) | 
 | 			isr_setup_packet_handler(ci); | 
 | 	} | 
 | } | 
 |  | 
 | /****************************************************************************** | 
 |  * ENDPT block | 
 |  *****************************************************************************/ | 
 | /** | 
 |  * ep_enable: configure endpoint, making it usable | 
 |  * | 
 |  * Check usb_ep_enable() at "usb_gadget.h" for details | 
 |  */ | 
 | static int ep_enable(struct usb_ep *ep, | 
 | 		     const struct usb_endpoint_descriptor *desc) | 
 | { | 
 | 	struct ci_hw_ep *hwep = container_of(ep, struct ci_hw_ep, ep); | 
 | 	int retval = 0; | 
 | 	unsigned long flags; | 
 | 	u32 cap = 0; | 
 |  | 
 | 	if (ep == NULL || desc == NULL) | 
 | 		return -EINVAL; | 
 |  | 
 | 	spin_lock_irqsave(hwep->lock, flags); | 
 |  | 
 | 	/* only internal SW should enable ctrl endpts */ | 
 |  | 
 | 	if (!list_empty(&hwep->qh.queue)) { | 
 | 		dev_warn(hwep->ci->dev, "enabling a non-empty endpoint!\n"); | 
 | 		spin_unlock_irqrestore(hwep->lock, flags); | 
 | 		return -EBUSY; | 
 | 	} | 
 |  | 
 | 	hwep->ep.desc = desc; | 
 |  | 
 | 	hwep->dir  = usb_endpoint_dir_in(desc) ? TX : RX; | 
 | 	hwep->num  = usb_endpoint_num(desc); | 
 | 	hwep->type = usb_endpoint_type(desc); | 
 |  | 
 | 	hwep->ep.maxpacket = usb_endpoint_maxp(desc); | 
 | 	hwep->ep.mult = usb_endpoint_maxp_mult(desc); | 
 |  | 
 | 	if (hwep->type == USB_ENDPOINT_XFER_CONTROL) | 
 | 		cap |= QH_IOS; | 
 |  | 
 | 	cap |= QH_ZLT; | 
 | 	cap |= (hwep->ep.maxpacket << __ffs(QH_MAX_PKT)) & QH_MAX_PKT; | 
 | 	/* | 
 | 	 * For ISO-TX, we set mult at QH as the largest value, and use | 
 | 	 * MultO at TD as real mult value. | 
 | 	 */ | 
 | 	if (hwep->type == USB_ENDPOINT_XFER_ISOC && hwep->dir == TX) | 
 | 		cap |= 3 << __ffs(QH_MULT); | 
 |  | 
 | 	hwep->qh.ptr->cap = cpu_to_le32(cap); | 
 |  | 
 | 	hwep->qh.ptr->td.next |= cpu_to_le32(TD_TERMINATE);   /* needed? */ | 
 |  | 
 | 	if (hwep->num != 0 && hwep->type == USB_ENDPOINT_XFER_CONTROL) { | 
 | 		dev_err(hwep->ci->dev, "Set control xfer at non-ep0\n"); | 
 | 		retval = -EINVAL; | 
 | 	} | 
 |  | 
 | 	/* | 
 | 	 * Enable endpoints in the HW other than ep0 as ep0 | 
 | 	 * is always enabled | 
 | 	 */ | 
 | 	if (hwep->num) | 
 | 		retval |= hw_ep_enable(hwep->ci, hwep->num, hwep->dir, | 
 | 				       hwep->type); | 
 |  | 
 | 	spin_unlock_irqrestore(hwep->lock, flags); | 
 | 	return retval; | 
 | } | 
 |  | 
 | /** | 
 |  * ep_disable: endpoint is no longer usable | 
 |  * | 
 |  * Check usb_ep_disable() at "usb_gadget.h" for details | 
 |  */ | 
 | static int ep_disable(struct usb_ep *ep) | 
 | { | 
 | 	struct ci_hw_ep *hwep = container_of(ep, struct ci_hw_ep, ep); | 
 | 	int direction, retval = 0; | 
 | 	unsigned long flags; | 
 |  | 
 | 	if (ep == NULL) | 
 | 		return -EINVAL; | 
 | 	else if (hwep->ep.desc == NULL) | 
 | 		return -EBUSY; | 
 |  | 
 | 	spin_lock_irqsave(hwep->lock, flags); | 
 | 	if (hwep->ci->gadget.speed == USB_SPEED_UNKNOWN) { | 
 | 		spin_unlock_irqrestore(hwep->lock, flags); | 
 | 		return 0; | 
 | 	} | 
 |  | 
 | 	/* only internal SW should disable ctrl endpts */ | 
 |  | 
 | 	direction = hwep->dir; | 
 | 	do { | 
 | 		retval |= _ep_nuke(hwep); | 
 | 		retval |= hw_ep_disable(hwep->ci, hwep->num, hwep->dir); | 
 |  | 
 | 		if (hwep->type == USB_ENDPOINT_XFER_CONTROL) | 
 | 			hwep->dir = (hwep->dir == TX) ? RX : TX; | 
 |  | 
 | 	} while (hwep->dir != direction); | 
 |  | 
 | 	hwep->ep.desc = NULL; | 
 |  | 
 | 	spin_unlock_irqrestore(hwep->lock, flags); | 
 | 	return retval; | 
 | } | 
 |  | 
 | /** | 
 |  * ep_alloc_request: allocate a request object to use with this endpoint | 
 |  * | 
 |  * Check usb_ep_alloc_request() at "usb_gadget.h" for details | 
 |  */ | 
 | static struct usb_request *ep_alloc_request(struct usb_ep *ep, gfp_t gfp_flags) | 
 | { | 
 | 	struct ci_hw_req *hwreq = NULL; | 
 |  | 
 | 	if (ep == NULL) | 
 | 		return NULL; | 
 |  | 
 | 	hwreq = kzalloc(sizeof(struct ci_hw_req), gfp_flags); | 
 | 	if (hwreq != NULL) { | 
 | 		INIT_LIST_HEAD(&hwreq->queue); | 
 | 		INIT_LIST_HEAD(&hwreq->tds); | 
 | 	} | 
 |  | 
 | 	return (hwreq == NULL) ? NULL : &hwreq->req; | 
 | } | 
 |  | 
 | /** | 
 |  * ep_free_request: frees a request object | 
 |  * | 
 |  * Check usb_ep_free_request() at "usb_gadget.h" for details | 
 |  */ | 
 | static void ep_free_request(struct usb_ep *ep, struct usb_request *req) | 
 | { | 
 | 	struct ci_hw_ep  *hwep  = container_of(ep,  struct ci_hw_ep, ep); | 
 | 	struct ci_hw_req *hwreq = container_of(req, struct ci_hw_req, req); | 
 | 	struct td_node *node, *tmpnode; | 
 | 	unsigned long flags; | 
 |  | 
 | 	if (ep == NULL || req == NULL) { | 
 | 		return; | 
 | 	} else if (!list_empty(&hwreq->queue)) { | 
 | 		dev_err(hwep->ci->dev, "freeing queued request\n"); | 
 | 		return; | 
 | 	} | 
 |  | 
 | 	spin_lock_irqsave(hwep->lock, flags); | 
 |  | 
 | 	list_for_each_entry_safe(node, tmpnode, &hwreq->tds, td) { | 
 | 		dma_pool_free(hwep->td_pool, node->ptr, node->dma); | 
 | 		list_del_init(&node->td); | 
 | 		node->ptr = NULL; | 
 | 		kfree(node); | 
 | 	} | 
 |  | 
 | 	kfree(hwreq); | 
 |  | 
 | 	spin_unlock_irqrestore(hwep->lock, flags); | 
 | } | 
 |  | 
 | /** | 
 |  * ep_queue: queues (submits) an I/O request to an endpoint | 
 |  * | 
 |  * Check usb_ep_queue()* at usb_gadget.h" for details | 
 |  */ | 
 | static int ep_queue(struct usb_ep *ep, struct usb_request *req, | 
 | 		    gfp_t __maybe_unused gfp_flags) | 
 | { | 
 | 	struct ci_hw_ep  *hwep  = container_of(ep,  struct ci_hw_ep, ep); | 
 | 	int retval = 0; | 
 | 	unsigned long flags; | 
 |  | 
 | 	if (ep == NULL || req == NULL || hwep->ep.desc == NULL) | 
 | 		return -EINVAL; | 
 |  | 
 | 	spin_lock_irqsave(hwep->lock, flags); | 
 | 	if (hwep->ci->gadget.speed == USB_SPEED_UNKNOWN) { | 
 | 		spin_unlock_irqrestore(hwep->lock, flags); | 
 | 		return 0; | 
 | 	} | 
 | 	retval = _ep_queue(ep, req, gfp_flags); | 
 | 	spin_unlock_irqrestore(hwep->lock, flags); | 
 | 	return retval; | 
 | } | 
 |  | 
 | /** | 
 |  * ep_dequeue: dequeues (cancels, unlinks) an I/O request from an endpoint | 
 |  * | 
 |  * Check usb_ep_dequeue() at "usb_gadget.h" for details | 
 |  */ | 
 | static int ep_dequeue(struct usb_ep *ep, struct usb_request *req) | 
 | { | 
 | 	struct ci_hw_ep  *hwep  = container_of(ep,  struct ci_hw_ep, ep); | 
 | 	struct ci_hw_req *hwreq = container_of(req, struct ci_hw_req, req); | 
 | 	unsigned long flags; | 
 | 	struct td_node *node, *tmpnode; | 
 |  | 
 | 	if (ep == NULL || req == NULL || hwreq->req.status != -EALREADY || | 
 | 		hwep->ep.desc == NULL || list_empty(&hwreq->queue) || | 
 | 		list_empty(&hwep->qh.queue)) | 
 | 		return -EINVAL; | 
 |  | 
 | 	spin_lock_irqsave(hwep->lock, flags); | 
 | 	if (hwep->ci->gadget.speed != USB_SPEED_UNKNOWN) | 
 | 		hw_ep_flush(hwep->ci, hwep->num, hwep->dir); | 
 |  | 
 | 	list_for_each_entry_safe(node, tmpnode, &hwreq->tds, td) { | 
 | 		dma_pool_free(hwep->td_pool, node->ptr, node->dma); | 
 | 		list_del(&node->td); | 
 | 		kfree(node); | 
 | 	} | 
 |  | 
 | 	/* pop request */ | 
 | 	list_del_init(&hwreq->queue); | 
 |  | 
 | 	usb_gadget_unmap_request(&hwep->ci->gadget, req, hwep->dir); | 
 |  | 
 | 	req->status = -ECONNRESET; | 
 |  | 
 | 	if (hwreq->req.complete != NULL) { | 
 | 		spin_unlock(hwep->lock); | 
 | 		usb_gadget_giveback_request(&hwep->ep, &hwreq->req); | 
 | 		spin_lock(hwep->lock); | 
 | 	} | 
 |  | 
 | 	spin_unlock_irqrestore(hwep->lock, flags); | 
 | 	return 0; | 
 | } | 
 |  | 
 | /** | 
 |  * ep_set_halt: sets the endpoint halt feature | 
 |  * | 
 |  * Check usb_ep_set_halt() at "usb_gadget.h" for details | 
 |  */ | 
 | static int ep_set_halt(struct usb_ep *ep, int value) | 
 | { | 
 | 	return _ep_set_halt(ep, value, true); | 
 | } | 
 |  | 
 | /** | 
 |  * ep_set_wedge: sets the halt feature and ignores clear requests | 
 |  * | 
 |  * Check usb_ep_set_wedge() at "usb_gadget.h" for details | 
 |  */ | 
 | static int ep_set_wedge(struct usb_ep *ep) | 
 | { | 
 | 	struct ci_hw_ep *hwep = container_of(ep, struct ci_hw_ep, ep); | 
 | 	unsigned long flags; | 
 |  | 
 | 	if (ep == NULL || hwep->ep.desc == NULL) | 
 | 		return -EINVAL; | 
 |  | 
 | 	spin_lock_irqsave(hwep->lock, flags); | 
 | 	hwep->wedge = 1; | 
 | 	spin_unlock_irqrestore(hwep->lock, flags); | 
 |  | 
 | 	return usb_ep_set_halt(ep); | 
 | } | 
 |  | 
 | /** | 
 |  * ep_fifo_flush: flushes contents of a fifo | 
 |  * | 
 |  * Check usb_ep_fifo_flush() at "usb_gadget.h" for details | 
 |  */ | 
 | static void ep_fifo_flush(struct usb_ep *ep) | 
 | { | 
 | 	struct ci_hw_ep *hwep = container_of(ep, struct ci_hw_ep, ep); | 
 | 	unsigned long flags; | 
 |  | 
 | 	if (ep == NULL) { | 
 | 		dev_err(hwep->ci->dev, "%02X: -EINVAL\n", _usb_addr(hwep)); | 
 | 		return; | 
 | 	} | 
 |  | 
 | 	spin_lock_irqsave(hwep->lock, flags); | 
 | 	if (hwep->ci->gadget.speed == USB_SPEED_UNKNOWN) { | 
 | 		spin_unlock_irqrestore(hwep->lock, flags); | 
 | 		return; | 
 | 	} | 
 |  | 
 | 	hw_ep_flush(hwep->ci, hwep->num, hwep->dir); | 
 |  | 
 | 	spin_unlock_irqrestore(hwep->lock, flags); | 
 | } | 
 |  | 
 | /** | 
 |  * Endpoint-specific part of the API to the USB controller hardware | 
 |  * Check "usb_gadget.h" for details | 
 |  */ | 
 | static const struct usb_ep_ops usb_ep_ops = { | 
 | 	.enable	       = ep_enable, | 
 | 	.disable       = ep_disable, | 
 | 	.alloc_request = ep_alloc_request, | 
 | 	.free_request  = ep_free_request, | 
 | 	.queue	       = ep_queue, | 
 | 	.dequeue       = ep_dequeue, | 
 | 	.set_halt      = ep_set_halt, | 
 | 	.set_wedge     = ep_set_wedge, | 
 | 	.fifo_flush    = ep_fifo_flush, | 
 | }; | 
 |  | 
 | /****************************************************************************** | 
 |  * GADGET block | 
 |  *****************************************************************************/ | 
 | static int ci_udc_vbus_session(struct usb_gadget *_gadget, int is_active) | 
 | { | 
 | 	struct ci_hdrc *ci = container_of(_gadget, struct ci_hdrc, gadget); | 
 | 	unsigned long flags; | 
 | 	int gadget_ready = 0; | 
 |  | 
 | 	spin_lock_irqsave(&ci->lock, flags); | 
 | 	ci->vbus_active = is_active; | 
 | 	if (ci->driver) | 
 | 		gadget_ready = 1; | 
 | 	spin_unlock_irqrestore(&ci->lock, flags); | 
 |  | 
 | 	if (ci->usb_phy) | 
 | 		usb_phy_set_charger_state(ci->usb_phy, is_active ? | 
 | 			USB_CHARGER_PRESENT : USB_CHARGER_ABSENT); | 
 |  | 
 | 	if (gadget_ready) { | 
 | 		if (is_active) { | 
 | 			pm_runtime_get_sync(&_gadget->dev); | 
 | 			hw_device_reset(ci); | 
 | 			hw_device_state(ci, ci->ep0out->qh.dma); | 
 | 			usb_gadget_set_state(_gadget, USB_STATE_POWERED); | 
 | 			usb_udc_vbus_handler(_gadget, true); | 
 | 		} else { | 
 | 			usb_udc_vbus_handler(_gadget, false); | 
 | 			if (ci->driver) | 
 | 				ci->driver->disconnect(&ci->gadget); | 
 | 			hw_device_state(ci, 0); | 
 | 			if (ci->platdata->notify_event) | 
 | 				ci->platdata->notify_event(ci, | 
 | 				CI_HDRC_CONTROLLER_STOPPED_EVENT); | 
 | 			_gadget_stop_activity(&ci->gadget); | 
 | 			pm_runtime_put_sync(&_gadget->dev); | 
 | 			usb_gadget_set_state(_gadget, USB_STATE_NOTATTACHED); | 
 | 		} | 
 | 	} | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | static int ci_udc_wakeup(struct usb_gadget *_gadget) | 
 | { | 
 | 	struct ci_hdrc *ci = container_of(_gadget, struct ci_hdrc, gadget); | 
 | 	unsigned long flags; | 
 | 	int ret = 0; | 
 |  | 
 | 	spin_lock_irqsave(&ci->lock, flags); | 
 | 	if (ci->gadget.speed == USB_SPEED_UNKNOWN) { | 
 | 		spin_unlock_irqrestore(&ci->lock, flags); | 
 | 		return 0; | 
 | 	} | 
 | 	if (!ci->remote_wakeup) { | 
 | 		ret = -EOPNOTSUPP; | 
 | 		goto out; | 
 | 	} | 
 | 	if (!hw_read(ci, OP_PORTSC, PORTSC_SUSP)) { | 
 | 		ret = -EINVAL; | 
 | 		goto out; | 
 | 	} | 
 | 	hw_write(ci, OP_PORTSC, PORTSC_FPR, PORTSC_FPR); | 
 | out: | 
 | 	spin_unlock_irqrestore(&ci->lock, flags); | 
 | 	return ret; | 
 | } | 
 |  | 
 | static int ci_udc_vbus_draw(struct usb_gadget *_gadget, unsigned ma) | 
 | { | 
 | 	struct ci_hdrc *ci = container_of(_gadget, struct ci_hdrc, gadget); | 
 |  | 
 | 	if (ci->usb_phy) | 
 | 		return usb_phy_set_power(ci->usb_phy, ma); | 
 | 	return -ENOTSUPP; | 
 | } | 
 |  | 
 | static int ci_udc_selfpowered(struct usb_gadget *_gadget, int is_on) | 
 | { | 
 | 	struct ci_hdrc *ci = container_of(_gadget, struct ci_hdrc, gadget); | 
 | 	struct ci_hw_ep *hwep = ci->ep0in; | 
 | 	unsigned long flags; | 
 |  | 
 | 	spin_lock_irqsave(hwep->lock, flags); | 
 | 	_gadget->is_selfpowered = (is_on != 0); | 
 | 	spin_unlock_irqrestore(hwep->lock, flags); | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | /* Change Data+ pullup status | 
 |  * this func is used by usb_gadget_connect/disconnet | 
 |  */ | 
 | static int ci_udc_pullup(struct usb_gadget *_gadget, int is_on) | 
 | { | 
 | 	struct ci_hdrc *ci = container_of(_gadget, struct ci_hdrc, gadget); | 
 |  | 
 | 	/* | 
 | 	 * Data+ pullup controlled by OTG state machine in OTG fsm mode; | 
 | 	 * and don't touch Data+ in host mode for dual role config. | 
 | 	 */ | 
 | 	if (ci_otg_is_fsm_mode(ci) || ci->role == CI_ROLE_HOST) | 
 | 		return 0; | 
 |  | 
 | 	pm_runtime_get_sync(&ci->gadget.dev); | 
 | 	if (is_on) | 
 | 		hw_write(ci, OP_USBCMD, USBCMD_RS, USBCMD_RS); | 
 | 	else | 
 | 		hw_write(ci, OP_USBCMD, USBCMD_RS, 0); | 
 | 	pm_runtime_put_sync(&ci->gadget.dev); | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | static int ci_udc_start(struct usb_gadget *gadget, | 
 | 			 struct usb_gadget_driver *driver); | 
 | static int ci_udc_stop(struct usb_gadget *gadget); | 
 |  | 
 | /* Match ISOC IN from the highest endpoint */ | 
 | static struct usb_ep *ci_udc_match_ep(struct usb_gadget *gadget, | 
 | 			      struct usb_endpoint_descriptor *desc, | 
 | 			      struct usb_ss_ep_comp_descriptor *comp_desc) | 
 | { | 
 | 	struct ci_hdrc *ci = container_of(gadget, struct ci_hdrc, gadget); | 
 | 	struct usb_ep *ep; | 
 |  | 
 | 	if (usb_endpoint_xfer_isoc(desc) && usb_endpoint_dir_in(desc)) { | 
 | 		list_for_each_entry_reverse(ep, &ci->gadget.ep_list, ep_list) { | 
 | 			if (ep->caps.dir_in && !ep->claimed) | 
 | 				return ep; | 
 | 		} | 
 | 	} | 
 |  | 
 | 	return NULL; | 
 | } | 
 |  | 
 | /** | 
 |  * Device operations part of the API to the USB controller hardware, | 
 |  * which don't involve endpoints (or i/o) | 
 |  * Check  "usb_gadget.h" for details | 
 |  */ | 
 | static const struct usb_gadget_ops usb_gadget_ops = { | 
 | 	.vbus_session	= ci_udc_vbus_session, | 
 | 	.wakeup		= ci_udc_wakeup, | 
 | 	.set_selfpowered	= ci_udc_selfpowered, | 
 | 	.pullup		= ci_udc_pullup, | 
 | 	.vbus_draw	= ci_udc_vbus_draw, | 
 | 	.udc_start	= ci_udc_start, | 
 | 	.udc_stop	= ci_udc_stop, | 
 | 	.match_ep 	= ci_udc_match_ep, | 
 | }; | 
 |  | 
 | static int init_eps(struct ci_hdrc *ci) | 
 | { | 
 | 	int retval = 0, i, j; | 
 |  | 
 | 	for (i = 0; i < ci->hw_ep_max/2; i++) | 
 | 		for (j = RX; j <= TX; j++) { | 
 | 			int k = i + j * ci->hw_ep_max/2; | 
 | 			struct ci_hw_ep *hwep = &ci->ci_hw_ep[k]; | 
 |  | 
 | 			scnprintf(hwep->name, sizeof(hwep->name), "ep%i%s", i, | 
 | 					(j == TX)  ? "in" : "out"); | 
 |  | 
 | 			hwep->ci          = ci; | 
 | 			hwep->lock         = &ci->lock; | 
 | 			hwep->td_pool      = ci->td_pool; | 
 |  | 
 | 			hwep->ep.name      = hwep->name; | 
 | 			hwep->ep.ops       = &usb_ep_ops; | 
 |  | 
 | 			if (i == 0) { | 
 | 				hwep->ep.caps.type_control = true; | 
 | 			} else { | 
 | 				hwep->ep.caps.type_iso = true; | 
 | 				hwep->ep.caps.type_bulk = true; | 
 | 				hwep->ep.caps.type_int = true; | 
 | 			} | 
 |  | 
 | 			if (j == TX) | 
 | 				hwep->ep.caps.dir_in = true; | 
 | 			else | 
 | 				hwep->ep.caps.dir_out = true; | 
 |  | 
 | 			/* | 
 | 			 * for ep0: maxP defined in desc, for other | 
 | 			 * eps, maxP is set by epautoconfig() called | 
 | 			 * by gadget layer | 
 | 			 */ | 
 | 			usb_ep_set_maxpacket_limit(&hwep->ep, (unsigned short)~0); | 
 |  | 
 | 			INIT_LIST_HEAD(&hwep->qh.queue); | 
 | 			hwep->qh.ptr = dma_pool_zalloc(ci->qh_pool, GFP_KERNEL, | 
 | 						       &hwep->qh.dma); | 
 | 			if (hwep->qh.ptr == NULL) | 
 | 				retval = -ENOMEM; | 
 |  | 
 | 			/* | 
 | 			 * set up shorthands for ep0 out and in endpoints, | 
 | 			 * don't add to gadget's ep_list | 
 | 			 */ | 
 | 			if (i == 0) { | 
 | 				if (j == RX) | 
 | 					ci->ep0out = hwep; | 
 | 				else | 
 | 					ci->ep0in = hwep; | 
 |  | 
 | 				usb_ep_set_maxpacket_limit(&hwep->ep, CTRL_PAYLOAD_MAX); | 
 | 				continue; | 
 | 			} | 
 |  | 
 | 			list_add_tail(&hwep->ep.ep_list, &ci->gadget.ep_list); | 
 | 		} | 
 |  | 
 | 	return retval; | 
 | } | 
 |  | 
 | static void destroy_eps(struct ci_hdrc *ci) | 
 | { | 
 | 	int i; | 
 |  | 
 | 	for (i = 0; i < ci->hw_ep_max; i++) { | 
 | 		struct ci_hw_ep *hwep = &ci->ci_hw_ep[i]; | 
 |  | 
 | 		if (hwep->pending_td) | 
 | 			free_pending_td(hwep); | 
 | 		dma_pool_free(ci->qh_pool, hwep->qh.ptr, hwep->qh.dma); | 
 | 	} | 
 | } | 
 |  | 
 | /** | 
 |  * ci_udc_start: register a gadget driver | 
 |  * @gadget: our gadget | 
 |  * @driver: the driver being registered | 
 |  * | 
 |  * Interrupts are enabled here. | 
 |  */ | 
 | static int ci_udc_start(struct usb_gadget *gadget, | 
 | 			 struct usb_gadget_driver *driver) | 
 | { | 
 | 	struct ci_hdrc *ci = container_of(gadget, struct ci_hdrc, gadget); | 
 | 	int retval = -ENOMEM; | 
 |  | 
 | 	if (driver->disconnect == NULL) | 
 | 		return -EINVAL; | 
 |  | 
 |  | 
 | 	ci->ep0out->ep.desc = &ctrl_endpt_out_desc; | 
 | 	retval = usb_ep_enable(&ci->ep0out->ep); | 
 | 	if (retval) | 
 | 		return retval; | 
 |  | 
 | 	ci->ep0in->ep.desc = &ctrl_endpt_in_desc; | 
 | 	retval = usb_ep_enable(&ci->ep0in->ep); | 
 | 	if (retval) | 
 | 		return retval; | 
 |  | 
 | 	ci->driver = driver; | 
 |  | 
 | 	/* Start otg fsm for B-device */ | 
 | 	if (ci_otg_is_fsm_mode(ci) && ci->fsm.id) { | 
 | 		ci_hdrc_otg_fsm_start(ci); | 
 | 		return retval; | 
 | 	} | 
 |  | 
 | 	pm_runtime_get_sync(&ci->gadget.dev); | 
 | 	if (ci->vbus_active) { | 
 | 		hw_device_reset(ci); | 
 | 	} else { | 
 | 		usb_udc_vbus_handler(&ci->gadget, false); | 
 | 		pm_runtime_put_sync(&ci->gadget.dev); | 
 | 		return retval; | 
 | 	} | 
 |  | 
 | 	retval = hw_device_state(ci, ci->ep0out->qh.dma); | 
 | 	if (retval) | 
 | 		pm_runtime_put_sync(&ci->gadget.dev); | 
 |  | 
 | 	return retval; | 
 | } | 
 |  | 
 | static void ci_udc_stop_for_otg_fsm(struct ci_hdrc *ci) | 
 | { | 
 | 	if (!ci_otg_is_fsm_mode(ci)) | 
 | 		return; | 
 |  | 
 | 	mutex_lock(&ci->fsm.lock); | 
 | 	if (ci->fsm.otg->state == OTG_STATE_A_PERIPHERAL) { | 
 | 		ci->fsm.a_bidl_adis_tmout = 1; | 
 | 		ci_hdrc_otg_fsm_start(ci); | 
 | 	} else if (ci->fsm.otg->state == OTG_STATE_B_PERIPHERAL) { | 
 | 		ci->fsm.protocol = PROTO_UNDEF; | 
 | 		ci->fsm.otg->state = OTG_STATE_UNDEFINED; | 
 | 	} | 
 | 	mutex_unlock(&ci->fsm.lock); | 
 | } | 
 |  | 
 | /** | 
 |  * ci_udc_stop: unregister a gadget driver | 
 |  */ | 
 | static int ci_udc_stop(struct usb_gadget *gadget) | 
 | { | 
 | 	struct ci_hdrc *ci = container_of(gadget, struct ci_hdrc, gadget); | 
 | 	unsigned long flags; | 
 |  | 
 | 	spin_lock_irqsave(&ci->lock, flags); | 
 |  | 
 | 	if (ci->vbus_active) { | 
 | 		hw_device_state(ci, 0); | 
 | 		spin_unlock_irqrestore(&ci->lock, flags); | 
 | 		if (ci->platdata->notify_event) | 
 | 			ci->platdata->notify_event(ci, | 
 | 			CI_HDRC_CONTROLLER_STOPPED_EVENT); | 
 | 		_gadget_stop_activity(&ci->gadget); | 
 | 		spin_lock_irqsave(&ci->lock, flags); | 
 | 		pm_runtime_put(&ci->gadget.dev); | 
 | 	} | 
 |  | 
 | 	ci->driver = NULL; | 
 | 	spin_unlock_irqrestore(&ci->lock, flags); | 
 |  | 
 | 	ci_udc_stop_for_otg_fsm(ci); | 
 | 	return 0; | 
 | } | 
 |  | 
 | /****************************************************************************** | 
 |  * BUS block | 
 |  *****************************************************************************/ | 
 | /** | 
 |  * udc_irq: ci interrupt handler | 
 |  * | 
 |  * This function returns IRQ_HANDLED if the IRQ has been handled | 
 |  * It locks access to registers | 
 |  */ | 
 | static irqreturn_t udc_irq(struct ci_hdrc *ci) | 
 | { | 
 | 	irqreturn_t retval; | 
 | 	u32 intr; | 
 |  | 
 | 	if (ci == NULL) | 
 | 		return IRQ_HANDLED; | 
 |  | 
 | 	spin_lock(&ci->lock); | 
 |  | 
 | 	if (ci->platdata->flags & CI_HDRC_REGS_SHARED) { | 
 | 		if (hw_read(ci, OP_USBMODE, USBMODE_CM) != | 
 | 				USBMODE_CM_DC) { | 
 | 			spin_unlock(&ci->lock); | 
 | 			return IRQ_NONE; | 
 | 		} | 
 | 	} | 
 | 	intr = hw_test_and_clear_intr_active(ci); | 
 |  | 
 | 	if (intr) { | 
 | 		/* order defines priority - do NOT change it */ | 
 | 		if (USBi_URI & intr) | 
 | 			isr_reset_handler(ci); | 
 |  | 
 | 		if (USBi_PCI & intr) { | 
 | 			ci->gadget.speed = hw_port_is_high_speed(ci) ? | 
 | 				USB_SPEED_HIGH : USB_SPEED_FULL; | 
 | 			if (ci->suspended) { | 
 | 				if (ci->driver->resume) { | 
 | 					spin_unlock(&ci->lock); | 
 | 					ci->driver->resume(&ci->gadget); | 
 | 					spin_lock(&ci->lock); | 
 | 				} | 
 | 				ci->suspended = 0; | 
 | 				usb_gadget_set_state(&ci->gadget, | 
 | 						ci->resume_state); | 
 | 			} | 
 | 		} | 
 |  | 
 | 		if (USBi_UI  & intr) | 
 | 			isr_tr_complete_handler(ci); | 
 |  | 
 | 		if ((USBi_SLI & intr) && !(ci->suspended)) { | 
 | 			ci->suspended = 1; | 
 | 			ci->resume_state = ci->gadget.state; | 
 | 			if (ci->gadget.speed != USB_SPEED_UNKNOWN && | 
 | 			    ci->driver->suspend) { | 
 | 				spin_unlock(&ci->lock); | 
 | 				ci->driver->suspend(&ci->gadget); | 
 | 				spin_lock(&ci->lock); | 
 | 			} | 
 | 			usb_gadget_set_state(&ci->gadget, | 
 | 					USB_STATE_SUSPENDED); | 
 | 		} | 
 | 		retval = IRQ_HANDLED; | 
 | 	} else { | 
 | 		retval = IRQ_NONE; | 
 | 	} | 
 | 	spin_unlock(&ci->lock); | 
 |  | 
 | 	return retval; | 
 | } | 
 |  | 
 | /** | 
 |  * udc_start: initialize gadget role | 
 |  * @ci: chipidea controller | 
 |  */ | 
 | static int udc_start(struct ci_hdrc *ci) | 
 | { | 
 | 	struct device *dev = ci->dev; | 
 | 	struct usb_otg_caps *otg_caps = &ci->platdata->ci_otg_caps; | 
 | 	int retval = 0; | 
 |  | 
 | 	ci->gadget.ops          = &usb_gadget_ops; | 
 | 	ci->gadget.speed        = USB_SPEED_UNKNOWN; | 
 | 	ci->gadget.max_speed    = USB_SPEED_HIGH; | 
 | 	ci->gadget.name         = ci->platdata->name; | 
 | 	ci->gadget.otg_caps	= otg_caps; | 
 |  | 
 | 	if (ci->platdata->flags & CI_HDRC_REQUIRES_ALIGNED_DMA) | 
 | 		ci->gadget.quirk_avoids_skb_reserve = 1; | 
 |  | 
 | 	if (ci->is_otg && (otg_caps->hnp_support || otg_caps->srp_support || | 
 | 						otg_caps->adp_support)) | 
 | 		ci->gadget.is_otg = 1; | 
 |  | 
 | 	INIT_LIST_HEAD(&ci->gadget.ep_list); | 
 |  | 
 | 	/* alloc resources */ | 
 | 	ci->qh_pool = dma_pool_create("ci_hw_qh", dev->parent, | 
 | 				       sizeof(struct ci_hw_qh), | 
 | 				       64, CI_HDRC_PAGE_SIZE); | 
 | 	if (ci->qh_pool == NULL) | 
 | 		return -ENOMEM; | 
 |  | 
 | 	ci->td_pool = dma_pool_create("ci_hw_td", dev->parent, | 
 | 				       sizeof(struct ci_hw_td), | 
 | 				       64, CI_HDRC_PAGE_SIZE); | 
 | 	if (ci->td_pool == NULL) { | 
 | 		retval = -ENOMEM; | 
 | 		goto free_qh_pool; | 
 | 	} | 
 |  | 
 | 	retval = init_eps(ci); | 
 | 	if (retval) | 
 | 		goto free_pools; | 
 |  | 
 | 	ci->gadget.ep0 = &ci->ep0in->ep; | 
 |  | 
 | 	retval = usb_add_gadget_udc(dev, &ci->gadget); | 
 | 	if (retval) | 
 | 		goto destroy_eps; | 
 |  | 
 | 	pm_runtime_no_callbacks(&ci->gadget.dev); | 
 | 	pm_runtime_enable(&ci->gadget.dev); | 
 |  | 
 | 	return retval; | 
 |  | 
 | destroy_eps: | 
 | 	destroy_eps(ci); | 
 | free_pools: | 
 | 	dma_pool_destroy(ci->td_pool); | 
 | free_qh_pool: | 
 | 	dma_pool_destroy(ci->qh_pool); | 
 | 	return retval; | 
 | } | 
 |  | 
 | /** | 
 |  * ci_hdrc_gadget_destroy: parent remove must call this to remove UDC | 
 |  * | 
 |  * No interrupts active, the IRQ has been released | 
 |  */ | 
 | void ci_hdrc_gadget_destroy(struct ci_hdrc *ci) | 
 | { | 
 | 	if (!ci->roles[CI_ROLE_GADGET]) | 
 | 		return; | 
 |  | 
 | 	usb_del_gadget_udc(&ci->gadget); | 
 |  | 
 | 	destroy_eps(ci); | 
 |  | 
 | 	dma_pool_destroy(ci->td_pool); | 
 | 	dma_pool_destroy(ci->qh_pool); | 
 | } | 
 |  | 
 | static int udc_id_switch_for_device(struct ci_hdrc *ci) | 
 | { | 
 | 	if (ci->is_otg) | 
 | 		/* Clear and enable BSV irq */ | 
 | 		hw_write_otgsc(ci, OTGSC_BSVIS | OTGSC_BSVIE, | 
 | 					OTGSC_BSVIS | OTGSC_BSVIE); | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | static void udc_id_switch_for_host(struct ci_hdrc *ci) | 
 | { | 
 | 	/* | 
 | 	 * host doesn't care B_SESSION_VALID event | 
 | 	 * so clear and disbale BSV irq | 
 | 	 */ | 
 | 	if (ci->is_otg) | 
 | 		hw_write_otgsc(ci, OTGSC_BSVIE | OTGSC_BSVIS, OTGSC_BSVIS); | 
 |  | 
 | 	ci->vbus_active = 0; | 
 | } | 
 |  | 
 | /** | 
 |  * ci_hdrc_gadget_init - initialize device related bits | 
 |  * ci: the controller | 
 |  * | 
 |  * This function initializes the gadget, if the device is "device capable". | 
 |  */ | 
 | int ci_hdrc_gadget_init(struct ci_hdrc *ci) | 
 | { | 
 | 	struct ci_role_driver *rdrv; | 
 | 	int ret; | 
 |  | 
 | 	if (!hw_read(ci, CAP_DCCPARAMS, DCCPARAMS_DC)) | 
 | 		return -ENXIO; | 
 |  | 
 | 	rdrv = devm_kzalloc(ci->dev, sizeof(*rdrv), GFP_KERNEL); | 
 | 	if (!rdrv) | 
 | 		return -ENOMEM; | 
 |  | 
 | 	rdrv->start	= udc_id_switch_for_device; | 
 | 	rdrv->stop	= udc_id_switch_for_host; | 
 | 	rdrv->irq	= udc_irq; | 
 | 	rdrv->name	= "gadget"; | 
 |  | 
 | 	ret = udc_start(ci); | 
 | 	if (!ret) | 
 | 		ci->roles[CI_ROLE_GADGET] = rdrv; | 
 |  | 
 | 	return ret; | 
 | } |