| xj | b04a402 | 2021-11-25 15:01:52 +0800 | [diff] [blame] | 1 | What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/ |
| 2 | asic_health |
| 3 | |
| 4 | Date: June 2018 |
| 5 | KernelVersion: 4.19 |
| 6 | Contact: Vadim Pasternak <vadimpmellanox.com> |
| 7 | Description: This file shows ASIC health status. The possible values are: |
| 8 | 0 - health failed, 2 - health OK, 3 - ASIC in booting state. |
| 9 | |
| 10 | The files are read only. |
| 11 | |
| 12 | What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/ |
| 13 | cpld1_version |
| 14 | cpld2_version |
| 15 | |
| 16 | Date: June 2018 |
| 17 | KernelVersion: 4.19 |
| 18 | Contact: Vadim Pasternak <vadimpmellanox.com> |
| 19 | Description: These files show with which CPLD versions have been burned |
| 20 | on carrier and switch boards. |
| 21 | |
| 22 | The files are read only. |
| 23 | |
| 24 | What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/select_iio |
| 25 | Date: June 2018 |
| 26 | KernelVersion: 4.19 |
| 27 | Contact: Vadim Pasternak <vadimpmellanox.com> |
| 28 | Description: This file allows iio devices selection. |
| 29 | |
| 30 | Attribute select_iio can be written with 0 or with 1. It |
| 31 | selects which one of iio devices can be accessed. |
| 32 | |
| 33 | The file is read/write. |
| 34 | |
| 35 | What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/psu1_on |
| 36 | /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/psu2_on |
| 37 | /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/pwr_cycle |
| 38 | /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/pwr_down |
| 39 | Date: June 2018 |
| 40 | KernelVersion: 4.19 |
| 41 | Contact: Vadim Pasternak <vadimpmellanox.com> |
| 42 | Description: These files allow asserting system power cycling, switching |
| 43 | power supply units on and off and system's main power domain |
| 44 | shutdown. |
| 45 | Expected behavior: |
| 46 | When pwr_cycle is written 1: auxiliary power domain will go |
| 47 | down and after short period (about 1 second) up. |
| 48 | When psu1_on or psu2_on is written 1, related unit will be |
| 49 | disconnected from the power source, when written 0 - connected. |
| 50 | If both are written 1 - power supplies main power domain will |
| 51 | go down. |
| 52 | When pwr_down is written 1, system's main power domain will go |
| 53 | down. |
| 54 | |
| 55 | The files are write only. |
| 56 | |
| 57 | What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/ |
| 58 | reset_aux_pwr_or_ref |
| 59 | reset_asic_thermal |
| 60 | reset_hotswap_or_halt |
| 61 | reset_hotswap_or_wd |
| 62 | reset_fw_reset |
| 63 | reset_long_pb |
| 64 | reset_main_pwr_fail |
| 65 | reset_short_pb |
| 66 | reset_sw_reset |
| 67 | Date: June 2018 |
| 68 | KernelVersion: 4.19 |
| 69 | Contact: Vadim Pasternak <vadimpmellanox.com> |
| 70 | Description: These files show the system reset cause, as following: power |
| 71 | auxiliary outage or power refresh, ASIC thermal shutdown, halt, |
| 72 | hotswap, watchdog, firmware reset, long press power button, |
| 73 | short press power button, software reset. Value 1 in file means |
| 74 | this is reset cause, 0 - otherwise. Only one of the above |
| 75 | causes could be 1 at the same time, representing only last |
| 76 | reset cause. |
| 77 | |
| 78 | The files are read only. |