| xj | b04a402 | 2021-11-25 15:01:52 +0800 | [diff] [blame] | 1 | Kernel driver jc42 |
| 2 | ================== |
| 3 | |
| 4 | Supported chips: |
| 5 | * Analog Devices ADT7408 |
| 6 | Datasheets: |
| 7 | http://www.analog.com/static/imported-files/data_sheets/ADT7408.pdf |
| 8 | * Atmel AT30TS00, AT30TS002A/B, AT30TSE004A |
| 9 | Datasheets: |
| 10 | http://www.atmel.com/Images/doc8585.pdf |
| 11 | http://www.atmel.com/Images/doc8711.pdf |
| 12 | http://www.atmel.com/Images/Atmel-8852-SEEPROM-AT30TSE002A-Datasheet.pdf |
| 13 | http://www.atmel.com/Images/Atmel-8868-DTS-AT30TSE004A-Datasheet.pdf |
| 14 | * IDT TSE2002B3, TSE2002GB2, TSE2004GB2, TS3000B3, TS3000GB0, TS3000GB2, |
| 15 | TS3001GB2 |
| 16 | Datasheets: |
| 17 | Available from IDT web site |
| 18 | * Maxim MAX6604 |
| 19 | Datasheets: |
| 20 | http://datasheets.maxim-ic.com/en/ds/MAX6604.pdf |
| 21 | * Microchip MCP9804, MCP9805, MCP9808, MCP98242, MCP98243, MCP98244, MCP9843 |
| 22 | Datasheets: |
| 23 | http://ww1.microchip.com/downloads/en/DeviceDoc/22203C.pdf |
| 24 | http://ww1.microchip.com/downloads/en/DeviceDoc/21977b.pdf |
| 25 | http://ww1.microchip.com/downloads/en/DeviceDoc/25095A.pdf |
| 26 | http://ww1.microchip.com/downloads/en/DeviceDoc/21996a.pdf |
| 27 | http://ww1.microchip.com/downloads/en/DeviceDoc/22153c.pdf |
| 28 | http://ww1.microchip.com/downloads/en/DeviceDoc/22327A.pdf |
| 29 | * NXP Semiconductors SE97, SE97B, SE98, SE98A |
| 30 | Datasheets: |
| 31 | http://www.nxp.com/documents/data_sheet/SE97.pdf |
| 32 | http://www.nxp.com/documents/data_sheet/SE97B.pdf |
| 33 | http://www.nxp.com/documents/data_sheet/SE98.pdf |
| 34 | http://www.nxp.com/documents/data_sheet/SE98A.pdf |
| 35 | * ON Semiconductor CAT34TS02, CAT6095 |
| 36 | Datasheet: |
| 37 | http://www.onsemi.com/pub_link/Collateral/CAT34TS02-D.PDF |
| 38 | http://www.onsemi.com/pub/Collateral/CAT6095-D.PDF |
| 39 | * ST Microelectronics STTS424, STTS424E02, STTS2002, STTS2004, STTS3000 |
| 40 | Datasheets: |
| 41 | http://www.st.com/web/en/resource/technical/document/datasheet/CD00157556.pdf |
| 42 | http://www.st.com/web/en/resource/technical/document/datasheet/CD00157558.pdf |
| 43 | http://www.st.com/web/en/resource/technical/document/datasheet/CD00266638.pdf |
| 44 | http://www.st.com/web/en/resource/technical/document/datasheet/CD00225278.pdf |
| 45 | http://www.st.com/web/en/resource/technical/document/datasheet/DM00076709.pdf |
| 46 | * JEDEC JC 42.4 compliant temperature sensor chips |
| 47 | Datasheet: |
| 48 | http://www.jedec.org/sites/default/files/docs/4_01_04R19.pdf |
| 49 | |
| 50 | Common for all chips: |
| 51 | Prefix: 'jc42' |
| 52 | Addresses scanned: I2C 0x18 - 0x1f |
| 53 | |
| 54 | Author: |
| 55 | Guenter Roeck <linux@roeck-us.net> |
| 56 | |
| 57 | |
| 58 | Description |
| 59 | ----------- |
| 60 | |
| 61 | This driver implements support for JEDEC JC 42.4 compliant temperature sensors, |
| 62 | which are used on many DDR3 memory modules for mobile devices and servers. Some |
| 63 | systems use the sensor to prevent memory overheating by automatically throttling |
| 64 | the memory controller. |
| 65 | |
| 66 | The driver auto-detects the chips listed above, but can be manually instantiated |
| 67 | to support other JC 42.4 compliant chips. |
| 68 | |
| 69 | Example: the following will load the driver for a generic JC 42.4 compliant |
| 70 | temperature sensor at address 0x18 on I2C bus #1: |
| 71 | |
| 72 | # modprobe jc42 |
| 73 | # echo jc42 0x18 > /sys/bus/i2c/devices/i2c-1/new_device |
| 74 | |
| 75 | A JC 42.4 compliant chip supports a single temperature sensor. Minimum, maximum, |
| 76 | and critical temperature can be configured. There are alarms for high, low, |
| 77 | and critical thresholds. |
| 78 | |
| 79 | There is also an hysteresis to control the thresholds for resetting alarms. |
| 80 | Per JC 42.4 specification, the hysteresis threshold can be configured to 0, 1.5, |
| 81 | 3.0, and 6.0 degrees C. Configured hysteresis values will be rounded to those |
| 82 | limits. The chip supports only a single register to configure the hysteresis, |
| 83 | which applies to all limits. This register can be written by writing into |
| 84 | temp1_crit_hyst. Other hysteresis attributes are read-only. |
| 85 | |
| 86 | If the BIOS has configured the sensor for automatic temperature management, it |
| 87 | is likely that it has locked the registers, i.e., that the temperature limits |
| 88 | cannot be changed. |
| 89 | |
| 90 | Sysfs entries |
| 91 | ------------- |
| 92 | |
| 93 | temp1_input Temperature (RO) |
| 94 | temp1_min Minimum temperature (RO or RW) |
| 95 | temp1_max Maximum temperature (RO or RW) |
| 96 | temp1_crit Critical high temperature (RO or RW) |
| 97 | |
| 98 | temp1_crit_hyst Critical hysteresis temperature (RO or RW) |
| 99 | temp1_max_hyst Maximum hysteresis temperature (RO) |
| 100 | |
| 101 | temp1_min_alarm Temperature low alarm |
| 102 | temp1_max_alarm Temperature high alarm |
| 103 | temp1_crit_alarm Temperature critical alarm |