| /***************************************************************************** |
| * Copyright Statement: |
| * -------------------- |
| * This software is protected by Copyright and the information contained |
| * herein is confidential. The software may not be copied and the information |
| * contained herein may not be used or disclosed except with the written |
| * permission of MediaTek Inc. (C) 2005 |
| * |
| * BY OPENING THIS FILE, BUYER HEREBY UNEQUIVOCALLY ACKNOWLEDGES AND AGREES |
| * THAT THE SOFTWARE/FIRMWARE AND ITS DOCUMENTATIONS ("MEDIATEK SOFTWARE") |
| * RECEIVED FROM MEDIATEK AND/OR ITS REPRESENTATIVES ARE PROVIDED TO BUYER ON |
| * AN "AS-IS" BASIS ONLY. MEDIATEK EXPRESSLY DISCLAIMS ANY AND ALL WARRANTIES, |
| * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF |
| * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT. |
| * NEITHER DOES MEDIATEK PROVIDE ANY WARRANTY WHATSOEVER WITH RESPECT TO THE |
| * SOFTWARE OF ANY THIRD PARTY WHICH MAY BE USED BY, INCORPORATED IN, OR |
| * SUPPLIED WITH THE MEDIATEK SOFTWARE, AND BUYER AGREES TO LOOK ONLY TO SUCH |
| * THIRD PARTY FOR ANY WARRANTY CLAIM RELATING THERETO. MEDIATEK SHALL ALSO |
| * NOT BE RESPONSIBLE FOR ANY MEDIATEK SOFTWARE RELEASES MADE TO BUYER'S |
| * SPECIFICATION OR TO CONFORM TO A PARTICULAR STANDARD OR OPEN FORUM. |
| * |
| * BUYER'S SOLE AND EXCLUSIVE REMEDY AND MEDIATEK'S ENTIRE AND CUMULATIVE |
| * LIABILITY WITH RESPECT TO THE MEDIATEK SOFTWARE RELEASED HEREUNDER WILL BE, |
| * AT MEDIATEK'S OPTION, TO REVISE OR REPLACE THE MEDIATEK SOFTWARE AT ISSUE, |
| * OR REFUND ANY SOFTWARE LICENSE FEES OR SERVICE CHARGE PAID BY BUYER TO |
| * MEDIATEK FOR SUCH MEDIATEK SOFTWARE AT ISSUE. |
| * |
| * THE TRANSACTION CONTEMPLATED HEREUNDER SHALL BE CONSTRUED IN ACCORDANCE |
| * WITH THE LAWS OF THE STATE OF CALIFORNIA, USA, EXCLUDING ITS CONFLICT OF |
| * LAWS PRINCIPLES. ANY DISPUTES, CONTROVERSIES OR CLAIMS ARISING THEREOF AND |
| * RELATED THERETO SHALL BE SETTLED BY ARBITRATION IN SAN FRANCISCO, CA, UNDER |
| * THE RULES OF THE INTERNATIONAL CHAMBER OF COMMERCE (ICC). |
| * |
| *****************************************************************************/ |
| |
| /***************************************************************************** |
| * |
| * Filename: |
| * --------- |
| * gpio_hw.h |
| * |
| * Project: |
| * -------- |
| * Maui_Software |
| * |
| * Description: |
| * ------------ |
| * This file is intended for GPIO driver. |
| * |
| * Author: |
| * ------- |
| * ------- |
| * |
| *============================================================================ |
| * HISTORY |
| * Below this line, this part is controlled by PVCS VM. DO NOT MODIFY!! |
| *------------------------------------------------------------------------------ |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * |
| * removed! |
| * removed! |
| * removed! |
| * removed! |
| * removed! |
| * removed! |
| * removed! |
| * removed! |
| * removed! |
| * removed! |
| * removed! |
| * removed! |
| * removed! |
| * removed! |
| * removed! |
| * removed! |
| * removed! |
| * removed! |
| * removed! |
| * removed! |
| * removed! |
| * removed! |
| * removed! |
| * removed! |
| * removed! |
| *------------------------------------------------------------------------------ |
| * Upper this line, this part is controlled by PVCS VM. DO NOT MODIFY!! |
| *============================================================================ |
| ****************************************************************************/ |
| #ifndef _GPIO_SW_H |
| #define _GPIO_SW_H |
| |
| #include "drv_features_gpio.h" |
| #include "dcl.h" |
| #include "drv_comm.h" |
| #include "kal_general_types.h" |
| |
| |
| #if !defined(DRV_GPIO_OFF) |
| //#define __DRV_GPIO_REG_DBG__ |
| |
| #define GPIO_6280_INVAILD_INDEX 200 |
| #define GPIO_6280_MIN_PIN_A 60 |
| #define GPIO_6280_MAX_PIN_A 67 |
| #define GPIO_6280_MIN_PIN_B 83 |
| #define GPIO_6280_MAX_PIN_B 90 |
| |
| #if defined(DRV_GPIO_6280_SPECIAL_SET_REG) |
| typedef struct MT6280_GPIO_PULL_EN_SELL_MAP_TABLE_TAG |
| { |
| |
| kal_uint16 pullen_sel_index; |
| kal_uint16 pullen_reg_num; // which register |
| kal_uint16 pullen_remainder; // which bit in register |
| kal_uint16 pullsel_remainder; // which bit in register |
| }MT6280_GPIO_PULL_EN_SELL_MAP_Table_T; |
| |
| #endif |
| |
| #ifdef __DRV_GPIO_REG_DBG__ |
| |
| #define DRV_GPIO_WriteReg(addr,data) DRV_DBG_WriteReg(addr,data) |
| #define DRV_GPIO_Reg(addr) DRV_DBG_Reg(addr) |
| #define DRV_GPIO_WriteReg32(addr,data) DRV_DBG_WriteReg32(addr,data) |
| #define DRV_GPIO_Reg32(addr) DRV_DBG_Reg32(addr) |
| #define DRV_GPIO_WriteReg8(addr,data) DRV_DBG_WriteReg8(addr,data) |
| #define DRV_GPIO_Reg8(addr) DRV_DBG_Reg8(addr) |
| |
| |
| #define DRV_GPIO_ClearBits(addr,data) DRV_DBG_ClearBits(addr,data) |
| #define DRV_GPIO_SetBits(addr,data) DRV_DBG_SetBits(addr,data) |
| #define DRV_GPIO_ClearBits32(addr,data) DRV_DBG_ClearBits32(addr,data) |
| #define DRV_GPIO_SetBits32(addr,data) DRV_DBG_SetBits32(addr,data) |
| #define DRV_GPIO_ClearBits8(addr,data) DRV_DBG_ClearBits8(addr,data) |
| #define DRV_GPIO_SetBits8(addr,data) DRV_DBG_SetBits8(addr,data) |
| |
| #define DRV_GPIO_SetData(addr, bitmask, value) DRV_DBG_SetData(addr, bitmask, value) |
| #define DRV_GPIO_SetData32(addr, bitmask, value) DRV_DBG_SetData32(addr, bitmask, value) |
| #define DRV_GPIO_SetData8(addr, bitmask, value) DRV_DBG_SetData8(addr, bitmask, value) |
| |
| #else //__DRV_GPIO_REG_DBG__ |
| |
| #define DRV_GPIO_WriteReg(addr,data) DRV_WriteReg(addr,data) |
| #define DRV_GPIO_Reg(addr) DRV_Reg(addr) |
| #define DRV_GPIO_WriteReg32(addr,data) DRV_WriteReg32(addr,data) |
| #define DRV_GPIO_Reg32(addr) DRV_Reg32(addr) |
| #define DRV_GPIO_WriteReg8(addr,data) DRV_WriteReg8(addr,data) |
| #define DRV_GPIO_Reg8(addr) DRV_Reg8(addr) |
| |
| |
| #define DRV_GPIO_ClearBits(addr,data) DRV_ClearBits(addr,data) |
| #define DRV_GPIO_SetBits(addr,data) DRV_SetBits(addr,data) |
| #define DRV_GPIO_ClearBits32(addr,data) DRV_ClearBits32(addr,data) |
| #define DRV_GPIO_SetBits32(addr,data) DRV_DBGD_SetBits32(addr,data) |
| #define DRV_GPIO_ClearBits8(addr,data) DRV_ClearBits8(addr,data) |
| #define DRV_GPIO_SetBits8(addr,data) DRV_SetBits8(addr,data) |
| |
| #define DRV_GPIO_SetData(addr, bitmask, value) DRV_SetData(addr, bitmask, value) |
| #define DRV_GPIO_SetData32(addr, bitmask, value) DRV_SetData32(addr, bitmask, value) |
| #define DRV_GPIO_SetData8(addr, bitmask, value) DRV_SetData8(addr, bitmask, value) |
| |
| #endif //__DRV_GPIO_REG_DBG__ |
| |
| #else //#if !defined(DRV_GPIO_OFF) |
| |
| #define DRV_GPIO_WriteReg(addr,data) |
| #define DRV_GPIO_Reg(addr) drv_dummy_return() |
| #define DRV_GPIO_WriteReg32(addr,data) |
| #define DRV_GPIO_Reg32(addr) drv_dummy_return() |
| #define DRV_GPIO_WriteReg8(addr,data) |
| #define DRV_GPIO_Reg8(addr) drv_dummy_return() |
| |
| |
| #define DRV_GPIO_ClearBits(addr,data) |
| #define DRV_GPIO_SetBits(addr,data) |
| #define DRV_GPIO_ClearBits32(addr,data) |
| #define DRV_GPIO_SetBits32(addr,data) |
| #define DRV_GPIO_ClearBits8(addr,data) |
| #define DRV_GPIO_SetBits8(addr,data) |
| |
| #define DRV_GPIO_SetData(addr, bitmask, value) |
| #define DRV_GPIO_SetData32(addr, bitmask, value) |
| #define DRV_GPIO_SetData8(addr, bitmask, value) |
| |
| #endif //#if !defined(DRV_GPIO_OFF) |
| |
| extern kal_bool Is_6280_SPEC_GPIO( kal_uint16 pin); |
| extern kal_uint16 get_6280_spec_index( kal_uint16 pin_num); |
| extern void GPIO_MD_InitIO(char direction, char port); |
| extern void GPIO_MD_ModeSetup(kal_uint16 pin, kal_uint16 conf_dada); |
| extern DCL_UINT32 MD_get_gpio_pin_number(DCL_UINT32 flags); |
| |
| |
| |
| extern void GPIO_InitIO(char direction, char port); |
| extern char GPIO_ReadIO(char port); |
| extern kal_uint16 GPIO_ReadAll(void); |
| extern void GPIO_WriteIO(char data, char port); |
| extern void GPIO_WriteAll(kal_uint16 write_data); |
| extern char GPIO_ReturnMode(char port); |
| extern char GPO_ReturnMode(char port); |
| extern char GPIO_ReturnDir(char port); |
| extern char GPIO_ReturnDout(char port); |
| extern char GPO_ReturnDout(char port); |
| extern void GPO_WriteIO(char data,char port); |
| extern void GPO_WriteAll(kal_uint16 write_data); |
| extern void GPIO_ModeSetup(kal_uint16 pin, kal_uint16 conf_dada); |
| extern void GPO_ModeSetup(kal_uint16 pin, kal_uint16 conf_dada); |
| extern void initGPIO(void); |
| //extern void GPIO_init_(void); |
| extern void GPIO_ALLIO(void); |
| extern void GPIO_PullenSetup(kal_uint16 pin, kal_bool enable); |
| extern void GPIO_DinvSetup(kal_uint16 pin, kal_bool enable); |
| extern void GPIO_SetDebugMode(kal_bool enable); |
| extern void GPIO_SetClkOut(char clk_num, gpio_clk_mode mode); |
| extern void GPIO_SetClkDiv(char clk_num, gpio_clk_div div); |
| extern void GPIO_PullSelSetup(kal_uint16 pin, kal_bool pull_up); |
| extern void GPIO_TMDir(kal_bool pad_oe); |
| #ifdef __CUST_NEW__ |
| extern void GPIO_ModeSetup_FAST(kal_uint16 pin, kal_uint16 conf_dada); |
| extern void GPIO_InitIO_FAST(char direction, char port); |
| extern char GPIO_ReadIO_FAST(char port); |
| extern void GPIO_WriteIO_FAST(char data, char port); |
| #endif/* __CUST_NEW__ */ |
| extern void GPIO_Check_MultiPins(GPIOCheckStruct *check_ptr, kal_uint32 pin_cnt); |
| extern void GPIO_WriteIO_Force(char data, char port); |
| extern void GPIO_WriteIO_FAST2(char data, kal_uint16 no, kal_uint16 remainder_shift); |
| #endif |
| |